Question about 1996 kawasaki EN 500 Vulcan Classic

1 Answer

New battery, but no ignition lights come on - 1996 kawasaki EN 500 Vulcan Classic

Posted by on

  • Daniel
    Daniel Oct 13, 2013

    Main 30 amp fuse blown. Replaced and alls good with the world


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 89 Answers

Have you checked the main fuse? It's usually a 30amp fuse by itself and if you tried to jump the bike and connected the cables wrong, or accidentally connected the battery cables wrong when you put the new battery in, you may have blown the fuse.

Posted on Nov 06, 2013

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

2005 grand am no start no dash lights only power locks when turning key. New battery and ignition switch. What can it be?

No dash lights? no warning lights? Then ignition is not being turned to ON. Check all your fuses. Recheck your replacement work. Battery cables clean and tight? Headlights work? If lights are bright, battery is good and cables are good, so key to ON should light up warning lights on dash. If not something up still with your ignition switch.

Apr 04, 2017 | 2005 Pontiac Grand Am

1 Answer

How do I relight the pilot light

There are many different ignitions for pilot light burners. Some are piezo ( You have to press a button to ignite the pilot) , battery ignition, there will be a switch somewhere on the oven to press or switch , or full auto ignition, which is done by an electric ignition pack usually situated under the oven or mounted on the rear at the back. The full auto ignition will light the pilot when you turn the oven on. Make sure you have the gas on, battery is new (If battery ignition) or power is available.

Sep 30, 2015 | Kitchen Ranges

1 Answer

2006 cobalt battery saver on and security light on acts Luke battery is dead but it's not, will start if you jump a wire to starter but lugs like in 2nd gear.ran fine turned it off New switch

If you installed a new ignition switch and now the security light is on than the BCM has not relearned the new ignition switch. You can google "gm security relearn" to find instructions on how to do this.

Aug 14, 2015 | Cars & Trucks

1 Answer

2006 1200 portster new battery new starter wont start or turn over

Hi Anonymous, and the usual suspects are:
1.Ignition/Light Key Switch not in IGNITION position.
2.Engine Stop switch in the OFF position.
3.Discharged battery, loose or corroded connections (solenoid chatters).
4. Bank Angle Sensor tripped and Ignition/Light Key Switch not cycled to Off and then back to Ignition
5. Starter control circuit, relay or solenoid faulty.
6. Electric starter shaft pinion gear not engaging or over-running clutch slipping.
For a prime suspect please visit website below and good Luck.
Harley Davidson Sportster error codes and how to access them

Jan 06, 2014 | 2000 Harley Davidson FLSTC Heritage...

1 Answer

I have a 1974 custom deluxe truck and the ignition who come on new battery in car starter good and alternator is good

The reason to put in the push button for the starter is because the ignition switch had a problem in its start position. Now it may have failed completely. You will have to trace the wiring from the switch and the push buttonm maybe check some voltages. at the switch. Do the lights work off the battery? If no, look for a melted, bad fusible link near the battery. If the lights work (and other accessories), probably need a new ignition switch.
Good luck.

Oct 08, 2012 | Cars & Trucks

1 Answer

Doesn't light. New battery in igniter, can smell

clean elsctrode or it could just be out of postion to far away too light gas

Jan 08, 2010 | Heating & Cooling

1 Answer

No power with a brand new battery, not even ignition lights

Did you check your brand new battery? Fully charged? Hydro was good? You are connected properly ( + = + and - = - ) Do a volt check yourselg between + and - (frame)

If yes to all, Id be looking at the ignition switch.

Sep 03, 2009 | 2007 Aprilia RS 125

1 Answer

Battery not charging new alt new volt.

Ensure alternator excitation lamp (IGN) indicator lights when Ignition vehicle ignition is switched on prior to starting engine.
This light should normally extinguish as soon as motor starts.
(+12V is supplied through a small lamp to the Alternator 'IND' terminal whenever the Ignition switch is on).
Also check for any burnt out fusible link on the alternator output- terminal B+ should have battery voltage on it at all times.

Jun 12, 2009 | 1988 Lincoln Continental

Not finding what you are looking for?
1996 kawasaki EN 500 Vulcan Classic Logo

Related Topics:

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers


Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides