Question about Yamaha TW 200 Motorcycles

1 Answer

2008 Yamaha TW200 will not move when clutch released

Posted this problem before but entered wrong E-mail address.The bike starts and runs ok but will not move when the clutch is released.Acts as if it is still in neutral.The transmission appears to engage and the neutral light does go out.Tried clutch adjustment as per the owners manuel but that did not help.

Posted by on

  • Dick
    Dick May 11, 2010

    Being answered here.

  • Anonymous Mar 17, 2014

    to start the bike by the electric start the clutch lever has to be pulled in. Also, the nuetral light will not illuminate whether the bike is running or not running.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,567 Answers

Here are the possibilities > > Bent clutch push rod, missing push rod ball bearing or push rod, worn out actuator shaft cam, Missing friction disk (5), or pressure plate (4), totally worn out friction disks, clutch plates not installed in the correct sequence, extremely weak clutch springs, stripped teeth on the clutch hub, wrong clutch cable length (inner cable vs outer cable), broken shaft, bent then broken shift fork stems, broken slider gear dogs and a missing shift fork pin.

You didn't say if anyone had worked on the clutch or gearbox so I am throwing in nearly EVERYTHING possible that could create the problem. A little more background and most of the above can be ruled out. Get back to us.

Posted on Apr 22, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Besides clutch plate not releasing what else would make my harley not move while in gear


Hi, Derek assuming you're talking about your 1981 Sportster and the engine is running and you pull the clutch lever and shift into 1st and let the clutch lever out and the bike does not move then you may have the following issues:
1. Clutch not engaging.
2. The transmission is not in gear.
3. There is a broken component inside the transmission.
For more information about your issue and valuable "FREE" downloads that you will need, please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a wonderful day.
Bike runs shifts thru gears but doesn move Harley Davidson Forums
Harley Davidson Manuals Mark Workshop $7 very cheap
http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
http://www.harley-davidson.com/content/h-d/en_US/home/owners/maintain-your-bike/owners-manual.html
Instant Tech Relief To speak to me personally absolutely "FREE"

Jun 21, 2017 | Harley Davidson Motorcycles

1 Answer

How do i start my scooter with no key and no kickstart


No key?
You would need to hotwire the ignition. If you got caught with a hotwired bike the cops would start to ask hard questions.

No Kick start?
If it has a manual clutch you can turn the ignition on put it into second gear run push the bike up to running speed jump on it and release the clutch quickly to engage the engine.If its a centrifugal clutch (twist and go!) you cant bump start it.

But reading your question, I would ask whether you scooter is road worthy. Running and jumping on a moving bike with live electrical cables hanging out of it in a fuel rich environment is probably not a good idea!

Apr 15, 2015 | Motorcycles

1 Answer

My bike will not move when in gear.


The clutch is not engaging by the sounds of it ,does the clutch cable have some free play at the lever ?

Mar 22, 2015 | kawasaki Vulcan 1500 Classic Motorcycles

1 Answer

Ok everyone I have an off brand bike it's a johnny


sounds like a broken or missing keyway in the clutch hub/on the main shft

May 07, 2013 | Motorcycles

1 Answer

Cb100 clutch not engaging gears


check clutch cable put back ok, is the cable adjusted so it goes completely loose when not being used. is the clutch pushrod under casing put back wrong or mechanism that clutch cable leads to under panel replaced wrong

Mar 07, 2013 | Motorcycles

2 Answers

I have dr350 when I pull the clutch lever the clutch arm goes in all the way but it dosent take the bike out of gear


Try tighten cable adjusters, check cable for damage, check the clutch release arm for damage, if thats ok its worn clutch plates replace the clutch plates and check components for damage,

Jan 26, 2012 | 1993 Suzuki DR 350 S

1 Answer

My Bajaj Discover 125 DTSi showing a problem that whenever the vehicle ride through rain or after washing, chocking / missing happens. Bike starts but not able to move when we load gear and releases...


Dear Friend,

I was also facing the same problem with my Discover125 for a while.When i went to the service centre they said it happens with most of the Discover users.According to them there may be a possiblity of water going inside the Carburator and due to that this missing is happening.Earlier my choke was not working, but now i have rectified my choke assy and i use the choke when ever i face this problem and the bike runs ok. Even though i am not able to solve this problem permanently, i can ride my bike without much problem.Still i am trying to solve this problem permanently.If you find any solution please mail me to robmatkrl@gmail.com.

Best regards..
Robert Mathew
Kerala

Dec 18, 2010 | 2006 Bajaj Discover DTS-I

1 Answer

Im having trouble with my 2002 rm 250 clutchs... when i start to run the bike the cluth get like stuck or something and wildly releases at any moments and the bike runs off... its barely imposble to run...


  • A couple of things could be wrong. The clutch cable center wire could be frayed and catching up on the outer shell.
  • The clutch cable is bent or has been hit and crushed.
  • The outer and/or inner clutch hub is grooved and the friction plates are hanging up in the grooves.
  • You changed the gearbox oil and put in synthetic oil or an oil with "Special" additives. Synthetics can swell the cork on the friction plates and cause problems. Only use 10w40 motor oil in the gearbox.
  • A bad needle bearing at the pressure plate or on the shaft
  • The clutch was re-assembled incorrectly.
Go to the following website for an exploded view of your clutch. Please rate my answer. Thanks.
www.babbittsonline.com/pages/parts/viewbybrand/default.aspx

Aug 25, 2010 | 2003 Suzuki RM 250

1 Answer

How do I change on my Buell M2 cyclone?


First be sitting on the bike, what you will need do do is hold onto the handel bars and start the beast, let it warm for a minut or two.

Once you have done this you are almost redy to change :-)

Ok heres here it get interesting, youll need to rest you left foot on the left foot peg what ever you do don't get confused and put the wrong foot on the wrong foot peg or somthing really bad might happen when you make the change!!.
Ok assuming that you've done that youll need to pull the clutch in, once youve done that gentley but firmley stomp on the gear leaver (Its the one on the lefthand side of the bike just infront of the left hand foot peg)

OK, you've now made the first change!!!! from here youll want to gentley release that clutch, once you feel the BUELL start to move your gonna wanna give it a handfull of throttle whilst ajusting your left foot to be directley underneath the BUELL, once you foot is inline quickley grab that clutch in again and lift you foot thats underneath gear leaver, rince and repeat :-)



Jul 27, 2010 | 2000 Buell M2 Cyclone

2 Answers

1987 kx125 clutch wont engage


push rod bent ? too short ?

Aug 06, 2009 | 2003 kawasaki KX 125

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

494 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...