Question about Yamaha FZR 600 Motorcycles

1 Answer

New to the fazer have a problem locating nut to drain oil year 2002

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hi Dave,
Looking from front of bike, sump drain plug is on the Right.It will be necessary to remove the r/s Fairing, Once the fairing has been removed,the drain plug can be seen at the lower end of engine.
Hope this helps.

Posted on May 19, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Oil drain plugg striped out leaking how do i fix 2002 Grand marquise


Best way is to remove oil pan and weld in a new nut for drain plug, next best is to retap the threads to a slightly larger size and replace drain plug.( get plug then retap to fit the new plug.) may change from std thread to metric to be able to do this. Lastly the least effective way i know of- buy a small rubber expansion plug that fits in and tighten bolt that runs through it to expand the plug. ( this should work for a while till you can get it fixed properly.

Feb 28, 2017 | 2002 Mercury Grand Marquis

1 Answer

Where is the oil plugs for 2002 Triumph Daytona 955i locate at?


drain plug is located underneath the engine in the belly pan near to the oil filter , tip use a new copper washer to avoid a leak as the old one will drip oil garanteed

Sep 16, 2012 | 2002 Triumph Daytona 955i

1 Answer

Where is the oil drain plug on a 2002 BMW 325i


It is located on the oil pan, please be advised the oil pan is also the casting that houses the front differential, and the engine oil drain is the hex nut furthest to the rear of of the pan . You will need a 17mm wrench to remove the hex nut . After you drain the oil, DO NOT over tighten the plug . The proper torque is 25 newton/meters or about 20 foot/pounds

Sep 12, 2012 | 2002 BMW 5 Series

1 Answer

How do i change the oil and oil filter on a 2002 toyota 4runner


make sure your not draining the tranny fluid first of all, the drain plug( and I'm going by my 1999 runner is in front of the axle by the skid plate not behind it, I'll see if I can locate your year and get back to you

Jun 02, 2011 | 2002 Toyota 4Runner

1 Answer

Oil leaking from small hole in left side of cylinder head.only leaks after bike has been ridden.does not leak while in operation


the small hole is a drain hole from the spark plug recesses, so you may have a rocker cover leak.
Pull the tank off and have a look down the plug recesses and you should see where it is going

Apr 14, 2010 | 2002 Yamaha FZS 1000 Fazer

1 Answer

Hi. My 2002 Fazer is now on it's 3rd new battery. It seems to be drawing current when ignition is off (as I've measured it with a DVM) but I don't have any alarm or other device drawing power, only the...


What works when ign is off.Horn?Brake light?Those will draw power.Starters can drain battery to ground.Disconnect power wire to starter and then measure your dvm.Charger circuit goes thru alt.Disconnect relays 1 at a time checking dvm each time.

Mar 21, 2010 | 2002 Yamaha FZS 600 Fazer

1 Answer

Oil drain plug for 2006 flhrs


The nut is a 5/8 socket, its almost directly under the seat on the bottom of the engine. Best to pull out the dipstick to drain the oil quicker. Use a new washer when you refit the sump plug to prevent leaks.

Jan 26, 2010 | 2006 Harley Davidson FLHR Road king

1 Answer

How do you replace a thermostat on a 2002 toyota celica


Toyota Celica, Corolla, ECHO & MR2 1999-05Toyota Celica, Corolla, ECHO & MR2 1999-05

2002 Toyota Celica 1.8L MFI DOHC 4cyl


The thermostat is located in the water inlet housing that is connected to the lower radiator hose.
The thermostat is equipped with a by-pass valve. If the engine tends to overheat, removal of the thermostat would cause a decrease in cooling system efficiency.

CAUTION NEVER drain coolant directly onto the ground! NEVER open, service or drain the radiator or cooling system when hot; serious burns can occur from the steam and hot coolant. Also, when draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantities. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old.
d4c6b82.jpg

Fig. The oil filter must be removed to access the thermostat on the 5S-FE engine
  1. Position a suitable drain pan under the radiator drain **** and drain the cooling system.
  2. On the 7A-FE engine disconnect the engine coolant temperature switch harness from the water inlet housing.
de1afd5.jpg

Fig. Disconnect the engine coolant temperature switch wiring located on the side of the thermostat housing
  1. Remove the oil filter on 5S-FE engines.
  2. Loosen the hose clamp and disconnect the lower radiator hose from the water inlet housing.
d253a81.jpg

Fig. Loosen the radiator hose clamp ...

5746ade.jpg

Fig. ... then slide the hose off the thermostat housing
  1. Remove the two nuts from the water inlet housing and remove the housing from the water pump studs.
f78b0a7.jpg

Fig. Only two nuts hold the housing to the cylinder head

de736db.jpg

Fig. Pull the housing straight out to remove
  1. Remove the thermostat and rubber O-ring gasket from the water inlet housing.
f722bd2.jpg

Fig. Then pull the thermostat and gasket out

bd62248.jpg

Fig. Sometimes the gasket is stuck and has to be pried out of the head
To install:
  1. Make sure all the gasket surfaces are clean. Clean the inside of the inlet housing and the radiator hose connection with a rag.
  2. Install the new rubber O-ring gasket onto the thermostat. On 5S-FE engines, align the jiggle valve with the upper side of the stud bolt. Insert the thermostat into the housing.
abce49b.jpg

Fig. Only use the correct temperature range thermostat when for replacement

edd75f2.jpg

Fig. Align the jiggle valve within a 10°gap of the stud bolt-7A-FE engine

d56a45f.jpg

Fig. Align the jiggle valve within a 5°gap of the stud bolt-5S-FE engine
  1. Position the water inlet housing with the thermostat over the studs on the water pump and install the two nuts. Tighten the two nuts to 78-82 inch lbs. (9-10 Nm).
Don't forget to install a new O-ring onto the water inlet pipe. Apply soapy water to the O-ring prior to installation.
  1. Connect the lower radiator hose to the inlet housing and install the hose clamp.
  2. Attach the water temperature switch connector.
  3. Install the oil filter and check the oil level if removed.
  4. Fill the cooling system with a good brand of ethylene glycol based coolant.
  5. Start the engine and inspect for leaks.
  1. Remove the right hand cover under the engine.
  2. Drain the engine coolant.
  3. Remove the fan and generator V belt.
  4. Remove the generator assembly
  5. Remove the water inlet via the two nuts.
  6. Remove the thermostat.
To install:
  1. Install a new gasket onto the thermostat.
  2. Install the thermostat with the jiggle valve upward. It can be set within 10 degrees on either side of the prescribed position.
  3. Install the water inlet via the two nuts. Torque to 8 ft. lbs. (11 Nm).
  4. Install the generator assembly.
  5. Add engine coolant.
  6. Inspect for leaks.
  7. Replace the cover under the engine.
I hope help you with this (remember rated this help) Good luck.

Sep 29, 2009 | Toyota Celica Cars & Trucks

2 Answers

How do l change oil and filter on focus estate 2000.


Well, you'll want to get under your car and locate the oil pan. It should look something like a metal box and you'll find it in the middle of the engine area. There will be a nut, probably 9/16th size, so you';ll need a wrench or socket. When this becomes loose enough, use your fingers to twist it off. Be warned! Once this nut is off oil will immediatly become rushing out. You'll probably want to have a bucket or something to catch the oil. Once the oil has drained, tighten the nut back onto the oilpan. The oil filter shouldn't be far from the oilpan, probably a little bit upwards, you'll should be able to see it from where you drained your oil, but you can also sometimes spot it when leaning over your engine. Be sure to wet the lip of your new oil filter with clean/new oil before replacing it!

Feb 25, 2009 | 2000 Ford Focus

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

159 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...