Question about 2003 Suzuki RM 125

1 Answer

No spark just rebuil the whole motor and now i have no spark

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 89 Answers

You need to test your stator coil.

Posted on Apr 23, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why wont our tahoe start after rebuiling te motor


This may be due to the antitheft system of the truck not matching the the new motor. Very common on new motor swaps.

http://vatspasslockpasskeysecurityhelp.yolasite.com/

Jul 15, 2014 | 1995 Chevrolet Tahoe

1 Answer

Rebuils 4M40 motor now do not turn manually, still turned full revolution before head was installed. now that the head is on, it does not want to turn full revolution.


The cam shaft and crank shaft are not in the correct positions and the pistons are hitting the valves. Make sure that the mechanical timing is set correctly. If it is then there is something that fell into a cylinder when it was being assembled,

Nov 11, 2013 | Mitsubishi Cars & Trucks

1 Answer

Suzuki Timing


You need to purchase a factory service manual.

Apr 22, 2012 | Suzuki Motorcycles

1 Answer

Stored over winter. New battery fresh fuel wont start. Doesnt seem 2 be a spark peugeot speedfight 2 03. Any advice thanks clive


When gas sits it will, turn to a gel to make it simple. this can block the very small holes in the carb. There is a very simple way to check if the motor will run without taken everything apart. remove the air filter, get yourself a can of carb spray, brake cleaner, or wd-40. Open the throttle the whole way and spary which ever one you choose to use into the air intake let the throttle go and try to start the motor. if it starts then you know you have a fuel problem. If not then the next thing to check is the spark plug, remove the spark plug from the motor, place the spark plug cap back on the spark plug put the spark plug on the motor and spin the motor with the starter and see if you get spark. If you go you know that you have a fuel issue. check this out and lme know what you find if you need help with cleaning the carb let me know.
M.Woodring

Jun 23, 2011 | Peugeot Morini Corsaro 1200 Motorcycles

1 Answer

1998 Caddilac DeVille overheated water in the oil blown head gasket. would it beworth fixing.


It depends if you really like the car or not how much it costs.and how many original miles your engine has on it now. It might be less expensive to find and put a good low mileage used motor in there instead vs. replacing the Head Gasket and rebuiling the Head.

Jan 24, 2011 | 1998 Cadillac DeVille

2 Answers

My hoover dual v steamvac make loud noise and sparks


Be careful. This could be a shorted wire inside where the motor is. If there is sparks , something is exposed and touching. The motor also may be ready to give out. Unless your daring enough to open the whole thing up I would bring it to a shop or replace it.

Jul 13, 2009 | Hoover SteamVac Carpet/Upholstery Deep...

1 Answer

98 cr 125 has spark and gas but wont start.


When you rebuil the top end and pulled the power valve off did you put the screws bacvk in to the valve arm before puting the case and top end on cause you will either be closed or wide open on valve.and did you put the reeds back in? and make sure the floats are right and all jets are back in it the right way. try that

Jul 04, 2009 | 2002 Honda CR 125 R

1 Answer

Head number on engine


Your dealer has the manual with the proper ident code.
I lucky a better autoshop as well.
If you are extremely lucky you download the proper manual after 4 years browsing internet. Thus: Straight to proper dealer. Unless you plan to rebuil;d the whole thing with expensive original parts.
Buy a new car better.

Jan 24, 2009 | 1996 Mercury Cougar XR7

Not finding what you are looking for?
2003 Suzuki RM 125 Logo

Related Topics:

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

Richard
Richard

Level 2 Expert

83 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...