Question about 1994 Yamaha XJ 600 Diversion S

1 Answer

94 yamaha xj 600 wont rev over 6000 rpm

28000 miles, new plugs, new air filter k&n, vance hinse pipe.
top end (time-chain) seams a little noisy.

Posted by on

  • 2 more comments 
  • glouellette Apr 21, 2009

    what site below?

  • glouellette Apr 21, 2009

    THANK YOU JUST WHAT I NEEDED

  • glouellette Apr 21, 2009

    KOOL!!!!

  • Anonymous Mar 31, 2014

    timing chain is noisy

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,567 Answers

You bike is running rich on the main jet. Go down on the main jet size. Alternate to that, move the jet needle clip up one notch.

Go to the site below and you can download a free PDF service manual and parts manual for your bike. The service manual is 45th from the bottom of the Yamaha listings and the parts manual is 19th from the top. Now you can tune the carb and adjust the timing chain slack and a whole lot more. It saves my keystroke finger a lot of work also.

Please rate this solution. Thanks glouellette!

Posted on Apr 21, 2009

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Throttle position sensor noisy


Are you sure it's not the idle air valve as they can sound louder after changing to a high flow filter...take the filter off and shine a light in the intake when turning the ignition on and off. The idle valve is just inside the intake in a hole at the top...see if it moves in time with the noise that you hear

Mar 22, 2014 | Harley Davidson FLHTCUI Electra Glide...

1 Answer

I have a zzr 600 94 kawasaki bike ws just kept fr around 8months just used to start it every week, but no riding it I have gt the bike out it has the old fuel in it an I tried riding the bike it's all...


sounds like carbs need a service, are sliders free and moving correctly, is there any restriction to fuel flow, fuel tap, is air filter good. any air leaks around carbs

Mar 15, 2013 | Motorcycles

1 Answer

I have a 2005 vrscb v-rod and vance n hinces pipes with a vance n hince feul pack and my plugs are burning white


did you doing the fuelpak settings yourself?
go over the settings list and be sure you have the proper input values ie...stock or high flow air filter.... stcok headers or true duals and which style of V&H pipes you are using.
If you don't have the sheets with the values go to the V&H website and you can enter your data there and download the proper settings
hope that helps

Jun 17, 2011 | Harley Davidson VRSCB V-Rod Motorcycles

1 Answer

Haqve model #142 chain saw with very little oil to chain, cleaned every thing all holes are clear new oil and still have problem. also checked worm gear and it is good Have chain saw 3 years, only...


There is a filter in the tank on the end of the oil pick up pipe, if you have checked the gear you must have already removed the cluch and sprocket, if you now remove the two screws holding the pump and take it away, behind here is the pick up pipe, pull it out with long nose pliers and inspect the filter, the later machine has an up graded pick up and delivery tube in one to stop any leakage, if you have a seperate delivery and pick up pipe i would suggest changing to the later pipe part no. 545037101, if this still does not help it will have to be a new pump part no. 530014410.

Apr 07, 2011 | Husqvarna Garden

1 Answer

Yamaha YZF Thunderace 1000 no top end


Hi, Annita319 and the usual suspects are:
1. Spark plugs in bad condition or partially fouled.
2. Spark plug cables in bad condition and leaking check for spark leakage in the dark.
3. Spark plug gap too close or too wide.
4. Faulty ignition coil, module, and or sensor.
5. Battery nearly discharged.
6. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
7. Intermittent short circuit due to damaged wire insulation.
8. Dirty air filter
9. Intake air leak.
10. Water, dirt, or rust in the fuel system, fuel pump and/or filter.
11. Old dead or bad fuel.
12. Faulty fuel pressure regulator
13. Pinholes in the in tank plastic convoluted tubing from the pressure regulator to the quick disconnect check valve.
14. Fuel tank vent system plugged.
15. Throttle body controls misadjusted.
16. Damaged throttle body or intake seals.
17. Clogged or faulty fuel injectors.
18. Loose, dirty, or corroded ignition module connector at crankcase.
19. Faulty TPS, MAP, CKP, O2, and/or CMP sensors.
20. Incorrect valve timing.
21. Weak or broken valve springs.
22. Damaged intake or exhaust valve.
23. The control module may be in limp mode.
24. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Won rev past 6k rpm under load
http://www.r1-forum.com/forums/4-mechanical-help/80115-4500-5000-rpm-sputter.html
Yamaha YZF1000RJ Service Manual
OEM parts for Yamaha
YAMAHA YZF1000R Owner Manual

Apr 07, 2011 | 1998 Yamaha YZF Thunder ace 1000 R

1 Answer

Bike has 10K miles and this last time I changed oil, (used synthetic for first time) I put too much oil in (went above the top part of the circle. I didn't think is was a big deal. After a 20 minute ride,...


check your fill cap, the seal is know to wear out after time i have seen it on a lot of bmw's drain a little of the oil the right level there is a chance that the case breather pushed some oil into the air box.
clean it up go and take a ride see what happens.
Let me know what happens
M.Woodring

Jan 29, 2011 | 2004 BMW R 1200 C Independent

1 Answer

I have a 2000 Honda VT1100 Sabre Shadow. It's got aftermarket Vance and Hines pipes. It continues to have a backfire when moving up through the gears. I've had the jets (and K&N filter and plugs)...


When you installed the Vance and Hines pipes did you use new gaskets? Popping and backfiring is often caused by leaking copper o-rings in the head to head pipe connection , or head pipe to muffler gasket. Sealing the system will prevent oxygen igniting the unburned fuel in the exhaust pipe. Hopefully , this is all you need to stop the popping.

Nov 13, 2010 | Honda VT 1100 C Shadow Motorcycles

1 Answer

1993 Yamaha XJ600 (pre divi) Mikuni carbs surging


Hi, Bevstait and the usual suspects are:
1. Extremely lean fuel mixture.
2. Dirt, rust, water, or ethanol sludge in the fuel system.
3. Sticky throttle cables.
4. Multiple carburetors not in synchronization.
5. TPS sensor out of adjustment or faulty.
6. Wrong spark plugs for the type of service.
7. Throttle bodies not in synchronization (FI)
8. Faulty O2 sensor.
9. Clogged, stuck, or faulty IAC valve.
10. Aftermarket components not compatible with ECM.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
New Seca II surging bogging under mid RPM load NOT CARBS XJRider com
surge at steady throttle
Yamaha FJ Owners Workshop Manual
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-xj-owners-manuals

Oct 03, 2010 | 1993 Yamaha XJ 600 Diversion S

1 Answer

What is the routine service schedule for 2006 jetta?


oil/filter/lube every 3,500 miles synthetic oils every 5,000 miles
tire rotation wheel align check balance every 7500 miles
transmission service every 30,000 miles
air filter gas filter cabin air filter evry 30,000 miles
if engine has a timing belt(rubber substance) replace every 60,000 miles if it has a metal timing chain lasts almost forever
spark plugs should be good for 75,000-100,000 miles before replacing
Spark plug wires every 50,000-60,000 miles approx.
fuel injector flush every 30-40,000 miles approx.

Aug 12, 2010 | 2006 Volkswagen Jetta

Not finding what you are looking for?
1994 Yamaha XJ 600 Diversion S Logo

596 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

Tom

Level 2 Expert

314 Answers

dhnguyen

Level 2 Expert

281 Answers

vince

Level 3 Expert

1214 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...