Question about 2001 Suzuki VL 125 Intruder LC

1 Answer

The engine do not start. It is no sparks.

The engive won't fire. It is no sparks on the plug.

Posted by on

  • sveiwest Apr 23, 2009

    Thank you tombones49. I charged the battery and then the engine started and was runing fine. But, after a while it will not start. It looks like the battery has to be full charged before it fire. Any sugestions`?

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,567 Answers

Check the fuses. Next, check for spark but with a new spark plug. How good is the battery? Is the kill switch on? Does the side stand have a kill switch? Is it working properly? Check the operation of the ignition switch and all kill switches with a volt ohmmeter.

Check the wiring harness. Did a wire come unplugged? Are all wires clean and with solid connections? Any abraded or pinched wires? Is the bike in neutral and the neutral light is lit up? If no neutral light, check the neutral switch and neutral switch wire on center casing. If still no spark, get CDI system and coils checked at the dealers shop.

Please rate this answer. Thanks

Posted on Apr 21, 2009

  • tombones Apr 23, 2009

    Add water to the battery cells enough to cover the top of the cell plates. Charge the battery with a 2amp charger for 6 hours. Start the engine then put a volt meter on the battery terminals, red to red, black to black. Rev the bike to around 1900 rpm and see what the meter reads. It should read 14+ volts. If it does, and the battery does not hold the charge for more than a week then it is time for a new battery.



    How about giving my answers a top rating? Thanks!

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Check spark?


Benjamin, remove spark plug, attach plug wire onto plug, hold end of plug against cylinder head or a metal fastener that you know is going into engine for good ground. Make sure engine switch is in the on position, now pull engine over, observing the gap in plug for spark. If no spark get a new plug and try.
Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
How to check for Spark Plug Fire in any engine
How to Check the Spark Plug of Trimmer or Edger
Homelite String Trimmer Won Start No Spark

Jun 17, 2016 | Garden

1 Answer

Car won't start 2003 Dodge Stratus sxt coupe cranks but won't start what could b the problem? I tried spraying starting fluid in the air system but it still won't start!


i would check and see if spark pluges are firing. you can take one out and plug into spark plug wire then let the bottom of the plug sit on engine and get someone to try to start while you look at the plug to see if there is any fire. if you have no fire or fuel it would be the crankshaft sencer. it could be the timing belt but the motor would sound different turning over then it used to.

Dec 22, 2012 | Cars & Trucks

1 Answer

Won't start 1990 jeep cherokee laredo


Technically if the engine has compression, is getting spark at the right time and fuel, it should start.
Have you checked the spark plugs to see if they are fuel or oil fouled ?
Are you getting spark at the plugs or at the coil ?
Have you tried using carb cleaner or starting fluid in the throttle body ??
Have you checked fuel pressure to see if you are getting enough fuel to the injectors ?

Aug 16, 2012 | Jeep Cars & Trucks

1 Answer

Ryobi SS26 trimmer won't fire


Are you using a new plug,sometimes a used plug look's good,but doesn't work.

Jul 08, 2017 | Garden

1 Answer

Toro snowthrower model # HSK 635 won't restart, stated first time, ran about ten minutes, then died, put brand new spark plug in, getting good spark, just won't fire up, even when I tried a li


check and make sure its getting fuel. when trying to start, spray some engine starting fluid in spark plug hole. just a little bit. replace the plug then try to start it. if it starts then quits then its a fuel problem. fuel not reaching engine. good-day !

Jan 30, 2012 | Garden

1 Answer

My pressure washer doesnt seem to run properly. i have changed the fuel,air filter,spark plug and the oil. It will start but runs poorly.


Ok the first thing you need to check is if the spark is fireing. To do this you need to remove the plug plug it into the spark plug cap hold it on the cylinder head pull the engine over it will pull easy and see if you have a blueish spark jumping the gap on the plug . If you do its not an electrical prolbem . Then put the plug back and plug the ignition wire back and remove the air cleaner see if it will start then .witch the choke on . If it still won't start try pouring a small amount of fuel derictly into the carbuator if it runs for any time at all or even starts to fire then its a fuel issue eighter bad fuel or clogged filter or carbuator needs to be cleaned. You can even put a small amuont of fuel right into the spark plug hole then put the plug back in and it should start You need spark fuel and air for any engine to run if you have all three its automatic it will at least fire Good luckwith this

May 22, 2011 | Briggs & Stratton 2200 PSI Gas Pressure...

1 Answer

Engine turns over but won,t start


a combustion engine needs 3 thing`s to run 1st air (check air flow) 2nd fuel (check fuel system make sure it is getting gas to engine) 3rd fire (make sure your getting spark to your spark plug`s)

Oct 25, 2009 | 1999 GMC Sonoma

2 Answers

Firing order for ford 302


the engive is a v so here is the engine numbering also can be found on the intake manifold embossed on the intake of each cylinder
1-5-4-2-6-3-7-8
4 8
3 7
2 6
1 5

Oct 17, 2009 | 2004 Ford F150

2 Answers

2001 volkswagen golf


ok laker1761,

I would start with this: if its only happening when the engine is getting wet get a hair spray bottle, or any bottle and spray water on the engine when it is running to get it to act up. A blinking check engine light means you have a misfire, it most likely has something to do with your ignition.

The two most common things ive see when ive performed this test, was spark plug wire, or one of the coils. What you will be looking for is to see if the spark is arcing from one thing to another, like a wire, coil, something. I would start their, that is the quickest and easiest step to see you have a arcing spark.

Mar 10, 2009 | 2001 Volkswagen Golf

Not finding what you are looking for?
2001 Suzuki VL 125 Intruder LC Logo

564 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

Richard
Richard

Level 2 Expert

83 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...