Question about 1998 Honda CBR 600 F(3)W

1 Answer

My 1998 cbr 600 FW cuts out at low revs and will not

My 1998 cbr 600 cuts out at low revs and will not start up via ignition button but will by jump start. battery volts are good so battery is charging whilst engine is on, could this be somrthing to do with the rectifier?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Is this something that only happens when cold ? maybe you should consider taking plugs out and checking compression as piston rings could be kaput. hope this helps in some way :-)

gavin barraclough
GB Auto's

Posted on Apr 26, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I cant get my 1998 cbr 600 to start please help


Hi, Chuck and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, needs to be 12.5 volts or better and be able to pass a load test if necessary.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
5. Tip over sensor needs a reset.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand or clutch pull in switch/sensor.
9. Starter control circuit, relay, or solenoid faulty.
10. Main fuse or circuit breaker may be blown or faulty.
11. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
http://www.fireblades.org/forums/honda-cbr-600/85820-1998-cbr-600-f3-wont-start.html
What to do When Your Motorcycle Won Start
Honda CBR600F4I 2001 Service Manual
http://www.partsfish.com/page/oem-parts-for-honda
Honda CBR600F4i Owner Manual

Mar 09, 2017 | Honda CBR 600 RR Motorcycles

1 Answer

1998 honda cbr 600 fw fuel pump assembly join leak more so in hot weather, presuming the seal expands. can this be repaired?


It's not the seal that's expanding, it's the metal. In any case, you will need to put a new seal/ o rings in.

Jun 27, 2011 | 1998 Honda CBR 600 F(3)W

1 Answer

I just bought a 98 cbr 600 and was running . now when trying to starte it all i get is a clicking from the selenoid on the front of the battery is that whats wrong or something else . the fuse on it is...


If you push the starter button and the solenoid clicks, the button is good. Take a wire and jump the two posts on the solenoid or touch the two cables together. If your starter works, then you need a new solenoid. If you hold the starter button and tap on the starter with a plastic hammer and the starter works you need new starter brushes. Anything else wrong with the starter and you need to replace the starter assembly , unless the manufacturer sells replacement parts so you can repair the starter. most manufacturers only sell replacement starter brushes.

Nov 07, 2010 | 1998 Honda CBR 600 F(3)W

1 Answer

How do i remove the seat on a honda cbr 600 fw


to remove the seat on a 98 f3 you start on the left side by turning the bloack plastic lock near the bottom of the rear fairing just below the front of the seat.once you do that you pull slightly out on the plastic it will start to pull free from the seat there are3 or 4 plastics studs holding it so you pull the plastics starting at the front of the side fairing working your way to the back. then it will expose a bolt that holds the seat down it is a 1/2 inch socket to remove that. once you do that do the same procedure on the other side and the seat will come off :)

Apr 14, 2010 | 1998 Honda CBR 600 F(3)W

1 Answer

Engine loses revs on tickover and makes a stange clicking noise.


Could be a carburation problem, or could be one of the many ignition/carb control devices faulty, a workshop manual would guide you through the separate continuity tests for the separate components. |You would need to be able to use a circuit tester! The noise you hear maybe nothing but sommit thats become more audible to you because the general noise has dropped, but sounds to me like a fault on an electrical component on the carb. Good Luck - the Yeti

May 13, 2009 | 2005 Honda CBR 600 F

1 Answer

Max revs 14000 rpm.


You possibly sucked something in your fuel system clogging it a bit on the high rev., ?or just Get a new battery too.,.that could just be the issue.,.,

Jan 11, 2009 | 2004 Honda CBR 600 RR

1 Answer

Engine cuts out


I had a similar problem with my Honda XR. Turned out to be the Ignition Control module. The unit is probably sealed and unable to inspect. I figured it out by hitting it while the motor was running and it would cut out.

Nov 14, 2008 | 2008 Honda CBR 600 RR

Not finding what you are looking for?
1998 Honda CBR 600 F(3)W Logo

Related Topics:

284 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...