Question about 2004 kawasaki KX 125

1 Answer

Just bought a new bike

Does a kx 100 2004 model have a plastic propellar in the pump casing

Posted by on

  • Dick
    Dick May 11, 2010

    Are you talking about the water pump impeller?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 490 Answers

The water pump impeller is plastic yes

Posted on Apr 16, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I find the year my bike was made?


Look on plastic parts like underneath the saddle. Just as with cars, there might be a calendar dial showing the year and an arrow pointing to the month engraved on the plastic. To allow for assembly time, the year might be one later than printed on the plastic. Just keep in mind that plastic components might have been replaced through the life of the bike.

20029802-x4ti4kd13pz3emz5huheloyd-1-0.jpg Attached is the date stamp found on the bottom plastic cover of the saddle on my Dahon bike. I bought the bike brand new in 2015 and according to the stamp the bike was assembled with the saddle of '13. So we can quite accurately say the bike is a '13+1 (2014) model.

Sep 12, 2013 | Gary Fisher Wahoo

1 Answer

Hi i bought kx 250 f 2004 model . Can the bike seat hight be adjusted to lower hight to soot my wife length. How do i adjust the hight can you assit please?


Koubalink I am short as well, could ride fine, but as the bike is tough to kickstart, I needed the height to get a full range on the kickstart. Bought a Koubalink, fitted it in about 30 mins and worked out perfectly. Cheers

May 29, 2012 | 2004 kawasaki KX 250 F

1 Answer

Replacing Kawasaki kx 80 kick start return spring


Hi, easy job, if your bike is waer cooled, you dont say how old it is the old bikes were air cooled, undo all the water pipes attached to the r/h case all the water will escape, you can leave the oil inside the gearbox, if you lay the bike on its left hand side, lift the engine and block it up to make sure gear lever is not resting on the ground, as this will disengage when you remove the clutch cover on the r/hand side, undo all the fixing screws from the cover remove kickstart lever, tap the cover gently to loosen the cover and remove when loose, if the case will not come off check further for screws, sometimes hide inside water pumps etc, once you are ready to remove the cover, keep the kickstart shaft pushed inermost so that it stays located within the engine, once ready fully observe the location of spring mountins within the engine and replace the spring

Oct 17, 2011 | 2003 kawasaki KX 125

1 Answer

2003 yz 250 leaking water from hole at water pump. does it mean bearings bad? and if so how do you change it. all i find is the cover or the propellar. i cant find the bearing


leaking water means the seal is gone, the bearing is in the clutch case, often needs a new shaft as well if it has wear marks, replace the bearing, it will help the new seal last longer

Apr 10, 2010 | 2003 Yamaha YZ 250

1 Answer

F02 message but pump propellar doesn't spin totally around


The pump impeller should spin freely and cannot have any broken or missing blades. If the impeller has any broken/missing blades or if it won't spin freely, the pump is defective. Hope this helped and best wishes.

Aug 31, 2009 | Whirlpool Duet GHW9150P Front Load Washer

2 Answers

Need Intex Pump model #635 impeller


You know, I have made some amazing repairs on plastic items using nothing more than a soldiering iron! If you have the piece that broke off, you can carefully melt it back together. You can add more to the weld if you match the type of plastic but not too much or you imbalance it. In this case it looks like PVC. To repair it without the missing piece, form it out of epoxy putty, roughly shape it just before it sets up solid, & sand to finish.

Aug 30, 2009 | Intex Krystal Clear Model 635 Pool Filter...

1 Answer

Kx 125 2003


im pretty sure that the bike is a all in one menin that oil in tranny is same that flows in motor

Jul 22, 2009 | 2003 kawasaki KX 125

1 Answer

KX-TG6500 Battery wears out too quick


I called Panasonic and they anserwed all my questions. Thanks.

Mar 24, 2008 | Panasonic KX-TG6500 Cordless Phone

Not finding what you are looking for?
2004 kawasaki KX 125 Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75066 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...