Question about 2004 Suzuki RM 250

1 Answer

Power issue 2003 rm 250 loss of mid power and hesitation when roll on throttle clears out on top end when its in the power band. done everything to it but electrical.. need help asap

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,567 Answers

Remove and clean the carb. Before putting the slide back into the carb throat, move the clip on the jet needle down one notch. This should take care of the problems.

Please rate this answer. Thanks fastmxdude!

Posted on Apr 15, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Kymco Venox 250 2012 has no top end power. Also what are the float levels (stats on kymco site F17.5 R19) Not able to get site stats


Hi, Ben sorry you can't find the first and best tool you ever bought for your Kymco despair not, for a mere $0 you can download another one. For more information about your issue and free valuable downloads that you will need please visit the websites below. Good luck and have a nice day.
RM 250 no top end power Suzuki 2 Stroke
Thread CR 250 lacks top end power
Kymco Venox 250
http://www.dailymotos.com/wp-content/uploads/2012/01/Kymco+Venox+250250i+EN.pdf

Feb 25, 2016 | Kymco Motorcycles

1 Answer

Well the motor locked up and i couldnt kick it at all shifted threw all the gears just fine but i wuz messing with it and i ran through all the gears trying to turn the back wheel and knock it loose didnt...


If you are running 5th gear mid throttle the compression in the motor wasnt enough to push the piston back down

for the record ( i run a ts 250 savage 2 stroke ) i,ve done it my self it happends

try to keep it the power band you will be fine

good luck.

Mar 26, 2011 | 2004 Suzuki RM-Z 250

1 Answer

My 1989 rm 250 has just had a rebuild and is running fine but it wont go into the band


If you are referring to the power band,this is when your reed valves open.Check for cracked or damaged reeds.You need to remove carb and reeds are between carb and cylender.Check also the rubber boot that carb attaches to for cracks.this will cause intake air leak and cause reeds to not open properly.

Mar 21, 2011 | 2003 Suzuki RM 250

1 Answer

RM250 Power Issues


Hello if your motorcycle is blowing a lot of smoke and oil from the exhaust and running poorly,sounds like you have worn crankshaft bearings or the main seal is bad and sucking transmission oil.

Jun 07, 2010 | 2003 Suzuki RM 250

3 Answers

Bike boggs down no powerband rm 250


i have a 92 rm 250 an i just had it fully rebuilt an it laggs in power band an splutters an feels guttles

Oct 09, 2009 | 2003 Suzuki RM 250

1 Answer

2003 rm 250 while holding gas at mid throttle it spudders


Install a new NGK spark plug ONE HEAT RANGE HOTTER THAN STOCK . Now go back to the 32/1 gas mix. The 32/1 is what lubricates the crank bearings and piston. At 44/1 you are asking for a seized piston and/or the need for new crank bearings. Be sure to use Two Stroke Engine Oil in the gas, NOT motor oil. Use premium gas, not regular. This should take care of plug fouling.

Remove the float bowl and clean the entire carb with a spray carb cleaner from the auto parts store. Wear protective goggles to avoid getting spray in your eyes. Spray all the little airways and fittings in the carb. Remove the two screws on the outside throat of the carb and spray into the screw holes as well.

Be sure to put these two screws back in the same hole they came out of. IMPORTANT > do not tighten these two screws down. Only screw these in until they LIGHTLY seat. Now turn each screw one and one half turns outward. Put the rest of the carb back together, clean the air filter and install the carb. Let the float bowl fill then start the engine. This process should get you back on the road.


Please rate this solution as " FixYa " if all goes well. Thanks

Mar 28, 2009 | 2003 Suzuki RM 250

1 Answer

Loss of power


Clutch slippage would be a possibility. While rolling in 5th gear mid-range in the rpm band give the bike a lot of throttle. Do the rpms rise significantly without the speed of the bike increasing? If so you may need a new clutch or possibly just new springs. If you have put any oil additive it is possible your clutch friction plate(s) became contaminated.

Jan 03, 2009 | 2000 Honda NSR 125

Not finding what you are looking for?
2004 Suzuki RM 250 Logo

Related Topics:

247 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...