Question about 2003 Suzuki GSX-R 600

1 Answer

Wrecked need advice

03 gsxr 600. rebuilding, Poped into dealermode, Error codes c22 and c23 fixed c23 the tip sensor now atmospheric pressure sensor, will it run without it? i turn the key and all the pre start noises sound good, the fi and everything, On speedo in the corner it changes from fi to ---temp. Hit ignition and all i get is clicking, Anyone know what else i can try?

Posted by on

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

Try tightening battery, my bike clicks (very fast?!!) try screws n get bk to me

Posted on Feb 21, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2003 Suzuki TL1000R. It was running fine, then I stopped for gas. When I tried to start it, it would only turn over slowly, but would not fire, and the little F1 light came on. Help??


Open your rear seat and you'll see a black cap covering a connector/harness on the left side of the seat. If you take the cap off, you'll see it appears to be a normal harness. With your key in the ignition and bike turned to "on" (but not running), take a paperclip and short the two connectors out (by touching the two contacts together). This is known as a "ghetto dealer mode switch". It should display the error code on your display instead of just FI now.



Fuel Injection (FI) Code List:

C14 - THROTTLE POSITION SENSOR
C15 - ENGINE COOLANT TEMPERATURE SENSOR
C21 - INTAKE AIR TEMPERATURE SENSOR
C22 - ATMOSPHERIC PRESSURE SENSOR
C23 - TIPOVER SENSOR
C24 - IGNITION SIGNAL #1
C25 - IGNITION SIGNAL #2
C26 - IGNITION SIGNAL #3
C27 - IGNITION SIGNAL #4
C28 - SECONDARY THROTTLE VALVE ACTUATOR
C29 - SECONDARY THROTTLE POSITION SENSOR
C30 - SECONDARY THROTTLE CONTROL UNIT
C31 - GEAR POSITION SENSOR
C32 - INJECTOR SIGNAL #1
C33 - INJECTOR SIGNAL #2
C34 - INJECTOR SIGNAL #3
C35 - INJECTOR SIGNAL #4
C41 - FUEL PUMP CONTROL SYSTEM
C42 - IGNITION SWITCH SIGNAL
C46 - EXHAUST CONTROL VALVE ACTUATOR (1000 ONLY)

Jul 11, 2014 | 2003 Suzuki TL 1000 R

1 Answer

I have a 2004 gxsr 1000 with fault code c42. It wont start. oil light is flashing and displays FI on the temp. Bike just crank but will not fire it up. Help?


Grab a paperclip.

Place the bike in Neutral, and take the rear seat cowling off. On the side of the bike between the tail section and the trunk you will find a connector that is covered by a rubber cap, and has two wires running into it. Remove the cap and take note of which one of the 4 sockets the two wires go to. Turn the bike ON and start it up, short the wires out with the paperclip. Where your speedo was flashing a -CHEC- with the temp should now be a CXX error code. Write this code down. Then shut the bike off. Match the code up with the list below. Grab a Manual and get to work!

(What you have just done is put the bike into "Dealer Mode".

GSXR Fuel Injection (FI) Code List:

C14 - THROTTLE POSITION SENSOR
C15 - ENGINE COOLANT TEMPERATURE SENSOR
C21 - INTAKE AIR TEMPERATURE SENSOR
C22 - ATMOSPHERIC PRESSURE SENSOR
C23 - TIPOVER SENSOR
C24 - IGNITION SIGNAL #1
C25 - IGNITION SIGNAL #2
C26 - IGNITION SIGNAL #3
C27 - IGNITION SIGNAL #4
C28 - SECONDARY THROTTLE VALVE ACTUATOR
C29 - SECONDARY THROTTLE POSITION SENSOR
C30 - SECONDARY THROTTLE CONTROL UNIT
C31 - GEAR POSITION SENSOR
C32 - INJECTOR SIGNAL #1
C33 - INJECTOR SIGNAL #2
C34 - INJECTOR SIGNAL #3
C35 - INJECTOR SIGNAL #4
C41 - FUEL PUMP CONTROL SYSTEM
C42 - IGNITION SWITCH SIGNAL
C46 - EXHAUST CONTROL VALVE ACTUATOR (1000 ONLY)

03-04 GSXR1000 Workshop Manual Verify Download

Sep 26, 2012 | 2004 Suzuki GSX-R 1000

1 Answer

I have a Suzuki GSX-R 750 and my F1 one light has started to come on when I excelerate some speed what does that mean.


Odds are its your SET valve needing adjustment, have the codes pull on the bike. If it is the SET, you can remove the SET system easily or you can have it adjusted.

If you get a code.

The codes are as follows:
C14 - THROTTLE POSITION SENSOR
C15 - ENGINE COOLANT TEMPERATURE SENSOR
C21 - INTAKE AIR TEMPERATURE SENSOR
C22 - ATMOSPHERIC PRESSURE SENSOR
C23 - TIP OVER SENSOR
C24 - IGNITION SIGNAL #1
C25 - IGNITION SIGNAL #2
C26 - IGNITION SIGNAL #3
C27 - IGNITION SIGNAL #4
C28 - SECONDARY THROTTLE VALVE ACTUATOR
C29 - SECONDARY THROTTLE POSITION SENSOR
C30 - SECONDARY THROTTLE CONTROL UNIT
C31 - GEAR POSITION SENSOR
C32 - INJECTOR SIGNAL #1
C33 - INJECTOR SIGNAL #2
C34 - INJECTOR SIGNAL #3
C35 - INJECTOR SIGNAL #4
C41 - FUEL PUMP CONTROL SYSTEM
C42 - IGNITION SWITCH SIGNAL
C46 - EXHAUST CONTROL VALVE ACTUATOR
C00 - NO FAULT

Jun 28, 2011 | 2007 Suzuki GSX-R 750

1 Answer

Hi i have a 2004 sv1000s not getting any fire from the spark plug line i put the bike in dealer mode an i got c41 what dos that mean ?


GSXR Fuel Injection (FI) Code List:

C14 - THROTTLE POSITION SENSOR
C15 - ENGINE COOLANT TEMPERATURE SENSOR
C21 - INTAKE AIR TEMPERATURE SENSOR
C22 - ATMOSPHERIC PRESSURE SENSOR
C23 - TIPOVER SENSOR
C24 - IGNITION SIGNAL #1
C25 - IGNITION SIGNAL #2
C26 - IGNITION SIGNAL #3
C27 - IGNITION SIGNAL #4
C28 - SECONDARY THROTTLE VALVE ACTUATOR
C29 - SECONDARY THROTTLE POSITION SENSOR
C30 - SECONDARY THROTTLE CONTROL UNIT
C31 - GEAR POSITION SENSOR
C32 - INJECTOR SIGNAL #1
C33 - INJECTOR SIGNAL #2
C34 - INJECTOR SIGNAL #3
C35 - INJECTOR SIGNAL #4
C41 - FUEL PUMP CONTROL SYSTEM
C42 - IGNITION SWITCH SIGNAL
C46 - EXHAUST CONTROL VALVE ACTUATOR (1000 ONLY)

heres a list of fault codes hope it helps

John

Jan 04, 2011 | 2003 Suzuki SV 1000 S

1 Answer

Code 14 no start


error code 14
Faulty intake air pressure sensor hose
system; a hose is detached, causing
constant application of the
atmospheric pressure to the sensor;
or, the hose is clogged.
 Intake air pressure sensor hose is detached, clogged,
kinked, or pinched.
 Malfunction in ECU. 03

Jan 01, 2011 | Yamaha 1900 XV 1900 A Midnight Star

1 Answer

03 gsxr 600: f1 shows on l.e.d and red light flashes, tip over sensor ok stand sensor ok, there is a poor spark which is irregular, fuses ok fuel injectors make right noises and clicks, the bike was fine...


I almost pulled out my hair trying to figure out the same thing for about 4 days. Very low battery voltage...Its actually common I found out. Take your battery to autozone for a full charge. It should fix the issue.

Feb 21, 2010 | 2003 Suzuki GSX-R 600

1 Answer

F1 code on my 2006 suzuki gsxr. it just started an 2 hrs ago drove it home in 20 degree weather now f1 code and no start


When the red light comes on, eg (F1) use these fault codes to find your problem. To extract the codes from the computer system, there is a two pinned connector hanging out of the wiring harness, on the left hand rear of the bike, (say above the pillion foot peg under rear trim. Be sure not to confuse the other connector used by the Suzuki Workshop Mechanics, as this has four or five wires to the connector) After locating the one with only two wires at the back, use a split pin or paper clip to bridge the two wires togeather and turn the ignition to the ON position. You should now be able to read the code on the console. The fault codes are as follows,,
**** GSXR Fuel Injection (FI) Code List:*****
C14 - THROTTLE POSITION SENSOR
C15 - ENGINE COOLANT TEMPERATURE SENSOR C21 - INTAKE AIR TEMPERATURE SENSOR
C22 - ATMOSPHERIC PRESSURE SENSOR
C23 - TIPOVER SENSOR
C24 - IGNITION SIGNAL #1
C25 - IGNITION SIGNAL #2
C26 - IGNITION SIGNAL #3
C27 - IGNITION SIGNAL #4
C28 - SECONDARY THROTTLE VALVE ACTUATOR C29 - SECONDARY THROTTLE POSITION SENSOR C30 - SECONDARY THROTTLE CONTROL UNIT
C31 - GEAR POSITION SENSOR
C32 - INJECTOR SIGNAL #1
C33 - INJECTOR SIGNAL #2
C34 - INJECTOR SIGNAL #3
C35 - INJECTOR SIGNAL #4
C41 - FUEL PUMP CONTROL SYSTEM
C42 - IGNITION SWITCH SIGNAL

Feb 03, 2010 | 2006 Suzuki GSX-R 600

1 Answer

Error code c23 on dash. Bike starts runs for about a minute then shuts off.


You have a bad "Tip Over Sensor", or the connector to it is loose.
Here's a clip from the error code manual:

c23 = Tip Over Sensor

The sensor voltage should be less than the following for more than 2 seconds after ignition switch turns ON.
(0.25 < sensor voltage < 4.85 V)
Without the above value, C23 is indicated
Troubleshoot: Tip Over Sensor, wiring/coupler connection

A repair manual for your bike will show the location and test parameters for the sensor.

I hope this helps!

Nov 28, 2009 | 1998 Suzuki GSX-R 750 W

1 Answer

Red light on odometer comes on.... And f1 light also


That is the Suzuki equivalent to a "Check engine light"

Turn your key on and verify the FI light is on and that your red kill switch is set to 'Run'

Remove your seat and behind the battery area you should find a white 6 pin connector (likely with a black rubber boot on it) Using a paperclip connect the white/red striped wire to the black/white striped wire.

Your display should Now read whatever codes are active.
If it reads C00- then there are no active codes. Note that when you turn the key off, the memory is erased so if you have an intermittent fault you should not turn the key off until you pull the codes.

Codes are as follows:

C11 - CAMSHAFT POSITION SENSOR
C12 - CRANKSHAFT POSITION SENSOR
C13 - INTAKE AIR PRESSURE SENSOR
C14 - THROTTLE POSITION SENSOR
C15 - ENGINE COOLANT TEMPERATURE SENSOR
C21 - INTAKE AIR TEMPERATURE SENSOR
C22 - ATMOSPHERIC PRESSURE SENSOR
C23 - TIPOVER SENSOR
C24 - IGNITION SIGNAL #1
C25 - IGNITION SIGNAL #2
C26 - IGNITION SIGNAL #3
C27 - IGNITION SIGNAL #4
C28 - SECONDARY THROTTLE VALVE ACTUATOR
C29 - SECONDARY THROTTLE POSITION SENSOR
C30 - SECONDARY THROTTLE CONTROL UNIT
C31 - GEAR POSITION SENSOR
C32 - INJECTOR SIGNAL #1
C33 - INJECTOR SIGNAL #2
C34 - INJECTOR SIGNAL #3
C35 - INJECTOR SIGNAL #4
C36 - SECONDARY INJECTOR SIGNAL #1
C37 - SECONDARY INJECTOR SIGNAL #2
C38 - SECONDARY INJECTOR SIGNAL #3
C39 - SECONDARY INJECTOR SIGNAL #4
C41 - FUEL PUMP CONTROL SYSTEM
C42 - IGNITION SWITCH SIGNAL
C46 - EXHAUST CONTROL VALVE ACTUATOR
C49 - PAIR CONTROL SOLENOID VALVE
C60 COOLING FAN CONTROL SYSTEM



Sep 09, 2009 | 2007 Suzuki GSX-R 1000

2 Answers

Yes have 2006 gsxr 600 it flashs F1 will not crank


there is a plug under your seat with 2 wires that you need to short out. The fI code is a dealer code like a check engine light on your car. You need the actual problem code. turn the bike on and keep it running short out the two wires in a white harness under your seat and then the f1 will change to a C## code.
C14 - THROTTLE POSITION SENSOR
C15 - ENGINE COOLANT TEMPERATURE SENSOR
C21 - INTAKE AIR TEMPERATURE SENSOR
C22 - ATMOSPHERIC PRESSURE SENSOR
C23 - TIPOVER SENSOR
C24 - IGNITION SIGNAL #1
C25 - IGNITION SIGNAL #2
C26 - IGNITION SIGNAL #3
C27 - IGNITION SIGNAL #4
C28 - SECONDARY THROTTLE VALVE ACTUATOR
C29 - SECONDARY THROTTLE POSITION SENSOR
C30 - SECONDARY THROTTLE CONTROL UNIT
C31 - GEAR POSITION SENSOR
C32 - INJECTOR SIGNAL #1
C33 - INJECTOR SIGNAL #2
C34 - INJECTOR SIGNAL #3
C35 - INJECTOR SIGNAL #4
C41 - FUEL PUMP CONTROL SYSTEM
C42 - IGNITION SWITCH SIGNAL
C46 - EXHAUST CONTROL VALVE ACTUATOR (1000 ONLY)

Also a good place to look to make sure you have the correct wires is :
http://www.gixxer.com/forums/showthread.php?t=192222
it is a great site to belong to for future issues or just for fun

Sep 03, 2009 | 2008 Suzuki GSX-R 600

Not finding what you are looking for?
2003 Suzuki GSX-R 600 Logo

326 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4535 Answers

Richard
Richard

Level 2 Expert

83 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...