Question about 2001 Husqvarna SM 610 S

1 Answer

Torque settings for the head bolts on a 1984 xc 125 husky

Just replaced piston and rings and need to know the torque settings for the head bolts, the studs are 8mm studs and have been told between 25 to 30 knm but would like a more accurate setting, thanks

Posted by on

  • silverfernwe Apr 28, 2009

    thanks tombones, i was told by the husky dealership that they didnt know so thanks for your help

  • silverfernwe Apr 28, 2009

    tombones since you have access to the service manual on my 84 xc 125 husky i was wondering if you know what pressure to pump the front and rear shocks to and do you or can you use nitrogen, thanks

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,567 Answers

The stud is 8mm with 1.25 thread. the torque, according to the service manual, is 19.6 to 21.6 Nm or 2.0 to 2.2 Kgm or 14.5 to 15.9 lb/ft.. It all depends on your favorite language.

Please take a moment to rate this answer. Thanks silverfernwe!

Posted on Apr 15, 2009

  • tombones Apr 28, 2009

    Post this as a new question and I will give you an answer your'e gonna love.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What's the steps in replacing my 5.3 engine?


You would need to drop the oil pan to remove the con rod bolts to be able to remove the piston. Sounds like you have the heads off. You would then pull the piston out drop a new one in (will need a piston ring compression tool) reconnect and torque the con rod. Reinstall heads and other xompnenets. Not sure how long or even if it will run as there could be other damage.

Oct 07, 2016 | Chevrolet 2002 Chevrolet Silverado 1500...

2 Answers

I have a 1987 kx 125 just put topend gasket set in with piston and rings and coolent is getting in the case bottom end anyone know why plz help me


It sounds as if you have rebuilt the engine without torqueing the head bolts. Although, it could be that the cylinder base gasket has been torn during the rebuild. Try to re-tighten the head bolts to the correct settings first. Good luck.

May 23, 2012 | 2003 kawasaki KX 125

1 Answer

I have a honda xr 125l 2003 which i bought in june only to find out the cylinderhead was damaged by the valve head which broke and hit the piston head. now i bought the cylinder head of cg 125 with the...


Hello epsom...you really should purchase the shop manual so you could see the illustrations and the step by step procedures on how to align timing marks and properly gap your piston rings. Plus so much more info that you are going to need to do the job right. Plus the manual has the torque specs. and the sequence---There is not enough room here to give you all the info u will need. Here is a link for the manual online, you might can find it a bit cheaper on Amazon. i hope this helps.

http://cgi.ebay.com/ebaymotors/Honda-XL-XR-125-200-Motorcycle-Service-Repair-Manual-/260718595181

Jul 17, 2011 | 2003 Honda XR 125 L

2 Answers

Im putting my 05 yz 125 top end back together my question was what is the torque specs on the head and on the jug


G'day. The torque specs for the 8mm head bolts is 18ft/lbs.the jug?(cylinder or barrell) is just tightened down even & firm, as there is no acess for a torque wrench.
OK. other things to note.
Clean the cylinder first in solvent(kero or fuel).Then in warm soapy water in a bucket. Dry-(compressed air is best for this-wear eye protection).once dry lubricate all power valves with oil.
Using a clean white rag-soak the end in your 2 stroke oil & wipe the inside of the cylinder surface untill the rag comes back clean(you will need to do it a couple of times-turn the rag over & do it again).Lube the new piston just before assembly-Also pour a little oil down the main bearing oil holes & over the big end too.
Other things to be sure of are-
Piston on the right way round-arrow to the exhaust.
Rings right way up. Some 2stroke dirtbike rings will only go one way up.Look CLOSELY at the ring ends-on the upper or lower surface there may be an etched dot or "T" or "N" or other marking. the mark goes facing up(on both rings unless single ring piston).
rings positioned with end gaps over the locating pins(the ring grooves have a pin in them to stop the ring turning)
Piston pin clips in correctly.
Powervalve moves freely.
Again-watch when you fit the cylinder-it can be tricky to keep the ring end gaps over the locating pins as you feed the cylinder over the piston.
Hope this all helps
Regards(done this a thousand times)Andrew Porrelli

May 04, 2011 | 2003 Yamaha YZ 250

1 Answer

Like to know torque settings for 1984 olds 307 .head gasket and dome


head bolt torque 125 ft Lbs. do it in two steps and lube threads on bolts.

valve cover torque 70 in. Lbs.

Feb 12, 2011 | Oldsmobile 88 Cars & Trucks

2 Answers

Torque setting cylinder head bolt 4 cylinder KIA sportage


I need the torque settings and pattern for a Kia Sportage 2.2

Nov 24, 2009 | 2001 Kia Sportage

2 Answers

Torque wrench settings for 97 hyundai lantra 1.8


They use throw away bolts. One use only, so don't reuse your old ones. You will need new ones. The smaller bolts 1st torque setting 22Ft/Lbs and the larger 26ft/lbs, the 2nd torque setting 60 degrees both bolt sizes and the 60 degrees for the third.

May 20, 2009 | 1997 Hyundai Elantra

2 Answers

Torque for head bolts for 1984 Toyota Corolla


head bolt toque specs are 40-47 ft-lbs

Mar 22, 2009 | 1984 Toyota Corolla

1 Answer

Loss of compression


Its PROBABLY just the rings, but ya gotta open it up to know for sure. If you are handy, and have a manual, you can do it, but it is tricky, especially getting the head bolts back right. The first time I did it, it took me a week, I had to consult my local shop, and I ended up blowin a head gasket cause I didnt torque the head bolts correctly

Mar 16, 2009 | 1995 Honda CA 125 Rebel

Not finding what you are looking for?
2001 Husqvarna SM 610 S Logo

253 people viewed this question

Ask a Question

Usually answered in minutes!

Top Husqvarna Experts

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

venugopal durairajan

Level 3 Expert

464 Answers

Are you a Husqvarna Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...