Question about 2007 Yamaha YZF-R6

1 Answer

2007 r6: hit starter while running, now I get nothing!!!

I started my yamaha r6. I then made the mistake of hitting the start switch again while the bike was already started. That of course killed the engine. Now it won't start at all...the start still clicks but it won't turn over. What the heck did I do?!? Please tell me I didn't screw things up too bad.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Yamaha Master
  • 767 Answers

It seems the starter has jammed in there! try to remove the starter and check it.

Posted on Apr 17, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Yamaha r6 wont start


Hi, Anonymous it should be noted that in order to "PROPERLY" diagnosis any electric starter issue it is "IMPERATIVE" that you begin with a fully charged battery 12.5 volts or better and be able to pass a proper load test, and the usual suspects are:
1. Battery terminals have loose or corroded connections.
2. Battery cables faulty due corroded or broken internal wiring at the cable connector especially the "NEGATIVE" cable which needs to be checked at "BOTH" ends.
3. Battery voltage, must be 12.5 volts or better, voltage from the battery to the main circuit breaker to the ignition switch to the security/ignition fuse to the TSM/TSSM module to the engine stop/run switch to the starter button to the starter relay to the green wire that connects to the starter solenoid can not drop more than 1/2 volt of battery voltage.
4. With a voltmeter connected to the battery, the ignition switch in the on position, the kill switch in the run position, the starter button depressed, starter engagement should not bring voltage below 8-9 volts.
If a lower voltage is produced a proper battery load test should be performed with a load tester to validate battery integrity or battery replacement.
5. Faulty starter relay, check continuity.
6. Faulty starter solenoid, check contact plate and shoes for excessive electrical erosion/etching, refurbish as necessary or invert contact plate and use the virgin backside. Check contact shoes for being loose. Replace solenoid if the negative function is still a final outcome.
7. Faulty starter, bench test starter with a 12-volt battery if negative function check, decontaminate and undercut armature commutator segments as necessary, check segments with an ohmmeter probe each one and the segment next to it for shorts. Have the armature tested with a growler and field coils, and brush plate with an ohm-meter for opens, shorts or grounds. Replace brushes if less than .438" It is generally cheaper to overhaul/refurbish a starter motor than buy a new one.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
http://www.r6-forum.com/forums/57-garage-mechanical-help/121022-bike-wont-start-makes-clicking-sound.html
Help r6 won start just clicks what wrong motorcycles
http://www.r6messagenet.com/forums/pdf/03-04R6_service_manual.pdf
OEM parts for Yamaha
http://www.yamaha-motor.com/assets/service/manuals/2007/lit-11626-20-43_r6_1310.pdf

Jun 23, 2014 | 2003 Yamaha YZF-R6

1 Answer

No power ignition when turn key


Hi, Anonymous and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, needs to be 12.5 volts or better and be able to pass a load test if necessary.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
5. Tip over sensor needs a reset.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand or clutch pull in switch/sensor.
9. Starter control circuit, relay, or solenoid faulty.
10. Main fuse or circuit breaker may be blown or faulty.
11. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
http://www.r6-forum.com/forums/46-general-discussions/165925-r6-wont-turn-over.html
http://www.r6messagenet.com/forums/welcome-center/161248-please-help-bike-wont-start-turn-over.html
2008 2009 Yamaha YZF R6 Service Manual R6 Moto Data Project
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-yz-owners-manuals

May 02, 2013 | Yamaha YZF-R6 Motorcycles

1 Answer

2003 yzf r6 hit start button but nothing happens


Hi, Anonymous and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, needs to be 12.5 volts or better and be able to pass a load test if necessary.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
5. Tip over sensor needs a reset.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand or clutch pull in switch/sensor.
9. Starter control circuit, relay, or solenoid faulty.
10. Main fuse or circuit breaker may be blown or faulty.
11. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
http://www.r6-forum.com/forums/57-garage-mechanical-help/152797-2002-r6-starts-starter-button-doesnt-work.html
Starting issue push the start button and nothing happens
2003 2004 Yamaha YZF R6 Service Manual R6 Moto Data Project
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-yz-owners-manuals

Apr 03, 2013 | 2003 Yamaha YZF-R6

1 Answer

The Bike Started ok then noticed nothing displaying on the dials and Rev counter stayed still, Switched it off then never started again?


Hi, Tudur and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, needs to be 12.5 volts or better and be able to pass a load test if necessary.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
5. Tip over sensor needs a reset.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand or clutch pull in switch/sensor.
9. Starter control circuit, relay, or solenoid faulty.
10. Main fuse or circuit breaker may be blown or faulty.
11. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
http://www.r6-forum.com/forums/46-general-discussions/165925-r6-wont-turn-over.html
http://www.r6messagenet.com/forums/welcome-center/161248-please-help-bike-wont-start-turn-over.html
2008 2009 Yamaha YZF R6 Service Manual R6 Moto Data Project
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-yz-owners-manuals

Feb 05, 2013 | 2008 Yamaha YZF-R6

1 Answer

Constant ringing under air box 07 r6


Hi, Anonymous and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, needs to be 12.5 volts or better and be able to pass a load test if necessary.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
5. Tip over sensor needs a reset.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand or clutch pull in switch/sensor.
9. Starter control circuit, relay, or solenoid faulty.
10. Main fuse or circuit breaker may be blown or faulty.
11. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
buzzing sound from under seat HELP
http://www.r6messagenet.com/forums/r6-maintenance-technical/28314-cdi-box-making-high-pitch-noise.html
2007 Yamaha YZF R6 Service Manual R6 Moto Data Project
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-yz-owners-manuals

Jun 19, 2012 | 2007 Yamaha YZF-R6

1 Answer

R6 will not turn over


How do you know if it is good if it won't make the starter motor turn? Some solenoids will still click but not send juice to the starter.

Feb 19, 2012 | Yamaha YZF-R6 Motorcycles

1 Answer

Hindi gumagana yng electronic swith starter


Hi, Ivanhinuguin at ang karaniwang suspects ay ang mga: 1. Ignition Lumipat wala sa "ON" posisyon. 2. Engine Run Lumipat sa "OFF" na posisyon. 3. Discharged baterya, mga pangangailangan upang maging 12.5 volts o mas mahusay at maaari able sa pumasa sa isang load test kung kinakailangan. 4. Lagyan ng check ang mga terminal ng baterya para sa pinsala o kaagnasan-check ang cable baterya sa "KAPWA" ay nagtatapos para maluwag, corroded, o nasirang connectors, "SA LOOB" at sa labas ng cable harness, magsagawa connector wiggle test at i-check cables na may isang ohmmeter kung kinakailangan. 5. Tip sa paglipas ng sensor ay nangangailangan ng isang pag-reset. 6. Ang maling pag-aapoy switch. 7. Ang maling starter button. 8. Ang maling kickstand o clutch pull sa switch / sensor. 9. Starter control circuit, relay, o solenoyde may depekto. 10. Main fuse o circuit breaker ay maaaring tinatangay ng hangin o may sira. 11. Suriin para sa engine pag-code. Para sa karagdagang impormasyon tungkol sa iyong isyu at mahalagang "LIBRE" download na kakailanganin mo paki-click ang link sa ibaba. Good luck at magkaroon ng magandang sa isang araw. 2007 Yamaha YZF R6 Service Manual R6 Moto Data Project
http://www.r6-forum.com/forums/57-garage-mechanical-help/152797-2002-r6-starts-starter-button-doesnt-work.html
http://www.r6messagenet.com/forums/r6-maintenance-technical/134796-ignition-button-not-working.html
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-yz-owners-manuals

Nov 06, 2010 | 2007 Yamaha YZF-R6

1 Answer

2006 Yamaha YZF-R6 will not start


try cleaning the battery terminals, check the battery voltage when you hit the starter, If you run it too long and it isnt charging a good battery you can damage the regulator again, same if you jump it off a car battery, it can cause damage

Mar 16, 2009 | 2002 Yamaha YZF-R6

1 Answer

2007 yamaha r6 wont start


Hi, Pellegrino60 and the usual suspects are:
1. Fuel tank empty.
2. Fuel supply valve/petcock turned off.
3. Fouled spark plugs.
4. Engine flooded as a result of overuse of the enricher.
5. Vacuum hose to the fuel supply valve/petcock disconnected, broken, cracked, or pinched.
6. Fuel valve/petcock or filter clogged.
7. Fuel line to carburetor or throttle body pinched or kinked.
8. Carburetor float stuck.
9. Fuel injectors clogged.
10. Severely discharged or damaged battery, you need 12.5 volts or better and be able to pass a load test if necessary.
11. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
12. Loose or corroded wire connection at the coil, battery or plug between ignition sensor and CDI box.
Spark plug cables in bad condition and shorting check for leakage in the dark, cable connections loose, or connected to the wrong cylinders.
13. Ignition timing incorrect due to a faulty MAP, CKP, O2, TPS, sensors.
14. Faulty neutral, clutch lever, or kickstand safety switch.
15. Faulty fuel pump or fuse or relay.
16. Faulty CDI box.
17. A stuck bent or burnt valve.
18. Tip over sensor needs a reset.
19. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
2007 Yamaha R6 Won Start
http://www.r6messagenet.com/forums/r6-maintenance-technical/132604-2007-r6-wont-start.html
2007 Yamaha YZF R6 Service Manual R6 Moto Data Project
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-yz-owners-manuals

Feb 07, 2009 | 2007 Yamaha YZF-R6

Not finding what you are looking for?
2007 Yamaha YZF-R6 Logo

320 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...