Question about 2001 KTM MXC 250

2 Answers

Was driving my o6 kx 85 . was at full speed and it cut out and refused to start and when i try to start it , it would backfire i think its getting a spark but no starting . does anyone know what the problem may be ?

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 490 Answers

Sounds like you might need to rebuild the top end and check the rod bearings remember when doing a top end always change piston and rings and use new base and head gasket

Posted on Apr 13, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Kx 85 knocking noise could this be top end bearing.should con rod have slight movement side to side

Posted on Jun 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My o6 polaris outlaw500 cuts back when full throttle not allowing me to reach full speed in any gear,what could cause this??? Jets are clean..


If it's fuel injected then it could be a computer prob, in which case I suggest unplugging the battery and waiting a few seconds before reconnecting it, but if it's carbed then try adjusting the throttle screw. Or if it's fuel injected and unhooking it fails it would have to have the TPS (throttle position sensor) replaced. Hope I help ya out!

Apr 27, 2016 | Garden

1 Answer

I have a 2009 Yamaha rhino 700 cutting out at half throttle and popping cuts out at 35 mph


Cutting out at 32mph - Yamaha Rhino Forum - Rhino Forums.net

www.rhinoforums.net > ... > Members > Forum Help, Questions and Info
Apr 23, 2011 - 12 posts - ‎8 authors Once it cuts out I let off the gas to let the speed drop a little, it pulls fine then ... The reason I say that is because feathering the throttle gets you 4 mph more .... Spent halfa night starting it and reving it trying to go somewhere but I'd give it ... Join Date: Sep2009 ... 2008 yamaha rhino 700 cuts out at 40 mph. 700 Sputtering with constant throttle
15 posts
Jul 18, 2012
Rhino missing/dying/backfiring when running on top ...
15 posts
Aug 12, 2011
2009 Rhino 700 Crank No Start
11 posts
Dec 12, 2010
full throttle
11 posts
Aug 31, 2009
More results from www.rhinoforums.net

Sep 27, 2015 | Yamaha Motorcycles

2 Answers

Why does my Westwood T1600 keeps cutting out


I would adjust valves to start.

Apr 30, 2014 | Garden

1 Answer

I am hoping that some of you jeep brainiacs out there can help with a suggestion of the problem with my 1992 Jeep Wrangler 4.0 hi-output. Symptoms: backfire from time to time....cuts off when driving, cuts...


I remember the "Parts Replace" routine all too well from my truck. It's probably the fuel filter needing to be changed, clogging up and clogging the flow.

Dec 19, 2010 | 2003 Jeep Wrangler

1 Answer

Hey i have an 84, 85, 86 can't recall. honda 500 shadow. it run fine. when it get hot or ran for a long time, then cut, its hard to start agian. after backfiring and cont. starting it starts? ciol pack...


think u hav water coolin-chec fluid or test pump--carb shud be cleaned or redone--yes also inspect igntion components--purchase a maintenance book online or go to library sec629-no wheelies

Jun 21, 2010 | 1984 Honda VT 500 C Shadow

2 Answers

When I am at near idle on my o6 KXf450, then snap to full throttle the bike stalls. At quarter to full, the bike runs fine.


It sounds like the accelerator pump on your carb isnt working properly..i hope this helps..Keith

Jul 02, 2009 | 2006 kawasaki KX 450 F

Not finding what you are looking for?
2001 KTM MXC 250 Logo

Related Topics:

444 people viewed this question

Ask a Question

Usually answered in minutes!

Top KTM Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Are you a KTM Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...