Question about 1995 Honda GL 1500 SE Gold Wing

1 Answer

Start switch hit & misses

If I hold the start button in it will sometimes start when released very slowly. Seems it started last fall I might have had to hit the switch a couple of times but it is far worse now.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 490 Answers

You need to change the starter button the contacts inside are not working anymore

Posted on Apr 13, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On button does not hold starting circuit.when start button is released drum stops turning


when you hit the start button it sends power to motor the start switch on motor is bad some modles you can replace motor switch but most of the time you need to replace motor

Mar 03, 2015 | Dryers

1 Answer

I have not used my endless summer patio heater since last fall. I bought a new tank of propaned, cleaned out the cobwebs checked all connections and tried to light up the heater. It does not work. I can...


Mike, the problem started when you turned the new tank ON. But, it is correctable most of the time.

Turn the LP tank valve OFF and disconnect the hose from the tank. Wait 5 minutes and reconnect the hose to the tank. Open the gas valve VERY, VERY, SLOWLY (Slow motion, slow). Once the tank valve is fully open, light the pilot and hold the gas control valve in for 30 seconds to 1 minute. Release the control valve and turn it to the ON position. Did the burner light and does the flame height look correct? If so, you solved the problem. Just remember to always turn the tank valve on Very, Very Slowly.

If the above didn't solve the problem, you will need to replace the heater's Hose/Regulator Assembly. A gas Grill's Hose Regulator Assembly should work and you can purchase one from any hardware store of home center that sells grills & accessories for about $30.00. Take your old one with you for comparison purposes.

Hope this helped you to troubleshoot & solve the problem. Thanks for choosing FixYa.

Sep 18, 2011 | Endless Summer Heating & Cooling

1 Answer

When we press the button to start the dryer, we hear the buzzing but the dryer does not move.


assume the buzzing quit when you release the start button. Open the dryer door and slowly rotate the dryer drum in a counterclockwise (CCW) direction. Rotate the drum 2-3 revolutions and then shut the door and see if it will start. If it continues to just hum and not start could indicate a voltage issue, motor issue or a friction issue. Open the door again and locate the door switch plunger in the upper or lower corner on the hinge side of the drum opening. Hold the plunger in while someone begins rotating the drum counterclockwise. While turning the drum counter clockwise and holding the door switch plunger inwards press the start button. If it starts, there is likely a friction problem or motor problem.

Jan 09, 2011 | Frigidaire Electric Dryer

1 Answer

Laptop won't boot, not even into BIOS. Screen stays blank it'll turn on for a bit (black screen) then switch off. Hard drive seems active, the only error indication is the caps and scroll lock flashing. It...


You need to launch the Last know good configuration to get this fixed.

Follow the steps below,

Step 1: Shut down your PC completely.
Step 2: Turn on the Power button.
Step 3: As soon as you turn it on start hitting the F8 key on your keyboard until you get to a black screen called "Windows Advanced option". (If you don't get to that that screen but you end up reaching the blue screen than that means you have delayed in hitting the F8 key. start again from step 1.)
Step 4: As soon as you reach "Windows Advanced option" use your down arrow keys to choose an option called "Last know good configuration".
Step 5: Select that and HIT ENTER.
Step 6: you PC will boot to the windows. If this fails then you need to perform repair install using the Operating system CD.

Dec 10, 2010 | Computers & Internet

1 Answer

My 96 Jetta intermitently will not start unless I turn the alarm on and then back off. The last time I had to hit the panic button on my remote, turn it off, and then the car would start. This seems to...


NO.to reset the factory immobiliser/alarm you must unlock/hold key over 30 secs....then lock/hold key over 30 secs....then press unlock button on remote for 30 secs....reset.(if you disconnect the battery you will have to reset AGAIN and input radio code.)

Nov 01, 2010 | 2006 Volkswagen Jetta

1 Answer

I have a whirlpool wash machine,the spin cycle does not spin all the time.sometimes i need to lift lid and start spinning it myself.it seems that something is holding it up


You need to take front panel off and check clutch, take a hammer and lightly hit clutch if black stuff falls off, that's whats holding it back. Add WD40 to it, and then it sould be back to normal, if it doesn't work then your washer is not worth repair

Jan 11, 2010 | Whirlpool Washing Machines

1 Answer

My unit is dead and won't turn on. I tried holding lap and mode then hitting power but nothing! Seems like the lap and mode buttons are frozen and won't release down when pushed. Please help!


Try this first :
Hold Lap and mode for 10 seconds or more, then release and wait ten other seconds.
Then hold start button for 10 seconds, device should start.

Aug 16, 2009 | Garmin Edge 305 GPS Receiver

1 Answer

Press start button and dryshuts off when start button is released


There is a switch assembly on the motor that activates when the motor is running. Centrifugal switch. It keeps it running when you release the switch. That is where to start. Eric

Jun 11, 2009 | Kenmore 74992 Gas Dryer

1 Answer

Takes a long time getting a signal


Try to delete the sattelite almanc: hold the down key while starting with power and release both buttons at the same time.
The first time the search will last even longer, but afterwards it should be faster.

Apr 12, 2008 | Garmin Forerunner 205 GPS Receiver

Not finding what you are looking for?
1995 Honda GL 1500 SE Gold Wing Logo

Related Topics:

105 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75066 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...