Question about 2000 Harley Davidson FXST Softail Standard

1 Answer

Rear brake pad installation

I am replacing rear brake pads and just need to know where the wire rods go- a picture would be great. Bike is really a 1996 FXSTS.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Harley Davidson Master
  • 43,732 Answers

Hi Marquettepar, for more information about your question please visit the websites below. Good luck and have nice day.
Replace rear brakes pads softail heritage EVO

Posted on Jun 18, 2015

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2336 Answers

SOURCE: replace rear brake pads

Remove right saddlebag, pull the two caliper mounting bolts and remove the caliper. Do not open bleeder or disconnect line. You will need to push a large screwdriver between the old pads before removing them in order to push the pucks back into the caliper or the new pads will not spread enough to reinstall. Then pull the two smaller bolts from the caliper and the pads will fall out. The pads are different for inside and outside, so pay attention, and remember, after reinstalling, before riding, be sure to pump brake pedal, and it may take a few stops before brakes stop as effectively as before.

Posted on Nov 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear brake caliper


Hi Anonymous, not really for more information about your question please visit the website below. Good luck and have nice day.
How to Replace Install Inspect Brake Pads on Harley Davidson Guide...

Jun 20, 2013 | 2010 Harley Davidson FLSTF Softail Fat Boy

1 Answer

2003 Suzuki VL 1500 Intruder LC REAR DISC RATTLE,HOW DO I REPLACE IT?


Hello Dale, this is an easy job on your bike. Use a flat head screw driver and remove the brake pad cover...it will pop off.
Remove the hairpin type clips off of the ends of the brake pad pins.... Use pliers & pull the brake pad pins out from the front of the rear brake caliper....Clean the rear brake caliper's piston with brake cleaner. Use a rag and wipe it clean...Reinsert the old brake pads into the caliper. Place a pry bar between the brake pads, then push the inner piston into the caliper body, this will allow room to install new pads.... Remove the old brake pads...Coat the brake pad pins and the new brake pads metal back plates with high-temperature grease.

Slip the new brake pads into the rear brake caliper, then push the brake pad pins halfway into the caliper. Slip the spring clips into place between the brake pads and the brake pad pins. Push the brake pad pins completely through the rear brake caliper. Push the hairpin clips back into the brake pad pin tips. Snap the brake pad cover onto the top of the rear brake caliper....

Pump the rear brake pedal until the pedal feels firm, indicating that the brake pads have closed around the brake rotor...No bleeding will be needed because the system was never opened - That's all there is to it...i hope this information is helpful & good luck with your bike.


11_23_2011_12_23_40_am.jpg

Nov 22, 2011 | 2003 Suzuki VL 1500 Intruder LC

2 Answers

Rear pad removal?


Here ya go! This is for the rear brake pads removal:

Removal & Installation
  1. Remove the brake master cylinder filler cap. Check brake fluid level in brake master cylinder reservoir. Remove fluid until brake master cylinder reservoir is half full.
  2. Raise and support the vehicle.
  3. Remove the wheel and tire assembly.
  4. Inspect the brake pads for wear or contamination. If worn, damaged or past specification, install new components.
  5. Remove the caliper pin bolts.
  6. Remove the rear disc brake caliper.
  7. Remove the brake pads and rail clips.
  8. Inspect the disc brake caliper for leaks. If leaks are found, disassembly is required.
  9. Installation is the reverse of removal. Observe the following torques:
    • Caliper bolts: 27 ft. lbs. (36 Nm)
  10. // // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 30; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]>

May 12, 2011 | 2002 Ford E350

1 Answer

When do you replace bike brake pads? I'm putting up some pictures of both my front and rear pads. I'm wondering if it's time to replace them. They seem pretty worn and the rear brakes won't lock up any...


Unless you have grooves in the rotors that almost gouge your fingernails, they should be good.

One indication of "needing pads" is, indeed, the loss of power; however, roughing them up CAN give you some more life, as it looks like you have pad material to work with. But if the roughing doesn't work, it's time for new....

...And I always recommend ceramic pads! Two years of awesome performance in my BB7's! Modulation is a step above ANYthing else I've used, and the stopping power is there all day long.

Dec 21, 2010 | Cycling

1 Answer

What tools needed to replace front brake pads & rotors


Brake Pads
Removal & Installation
Front





3.4L front disc brake assembly
toy_4run_34_frontbrakeassembly.gif








4.0L and 4.7L front disc brake assembly
toy_4run_frontbrakeassembly.gif



To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Clip, 2 caliper pins, the anti-rattle spring then remove the 2 brake pads
      and the 4 anti-squeal shims

To Install:

CAUTION
Only replace brake pads on 1 side of the
vehicle at a time. Failure to use this procedure could cause the caliper pistons
on the opposite side of the vehicle to pop out requiring the reconditioning or
replacement of the brake caliper.


  1. Remove a small amount of brake fluid from the master cylinder.
  2. Install a used brake pad into the caliper and compress the caliper pistons.
  3. Apply disc brake grease to both sides of the inner anti-squeal shims.
  4. Install or connect the following:

    • Anti-squeal shims to the new brake pads
      NOTE: When replacing worn pads, the anti-squeal shims must be replaced
      together with the pads.

    • 2 brake pads
    • Anti-rattle spring and the 2 caliper pins
    • Clip
    • Front wheel

  5. Depress the brake pedal several times to seat the brake pads.
  6. Check the brake fluid level and top off as needed.

Rear
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Rear wheel






      toy_4run_rearcalbolts.gif



    • 2 cylinder slide pins from rear caliper assembly
    • Caliper assembly from rear caliper mounting
    • 2 brake pads with anti-squeal shims from rear caliper mounting
    • 2 anti-squeal shims from each disc brake pads
    • Pad wear indicator plate from the inner side disc brake pad
    • 4 pad support plates from the rear caliper mounting

To Install:


  1. Install or connect the following:

    • 4 pad support plates on the rear caliper mounting
    • Pad wear indicator plate on the inside brake pad
      Note: Install the pad wear indicator facing downward.

    • Anti-squeal shims on each brake pad
    • 2 disc brake pads with anti-squeal shims to the caliper assembly

  2. Apply lithium soap base glycol grease to the sliding part of 2 caliper slide
    pins.
  3. Install or connect the following:

    • Disc brake caliper assembly with 2 caliper slide pins
    • Torque to 65 ft-lbs (88 Nm)
    • Rear wheel

  4. Depress the brake pedal several times to seat the brake pads.
  5. Check the brake fluid level and top off as needed.
--- Removal & Installation
Front
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Front brake caliper assembly

  3. Make matchmarks on the disc and the axle hub.
  4. Remove the front disc.

To Install:


  1. Align matchmarks and disc onto axle hub.
  2. Install or connect the following:

    • Front brake caliper assembly with the 2 bolts

      1. Torque to 90 ft-lbs (123 Nm)

    • Front wheel

Sep 23, 2010 | 2003 Toyota 4Runner

1 Answer

Is it very difficult to replace rear brake pads on a honda vtx 1300r


Personally I have never replaced pads on that particular bike but if it is like most rear disk pads, should not be too bad. I just remove the 2 bolts holding the caliper to the frame. Lift the caliper off enough to slide the pads out. Get a small C-clamp or something so you can gently push the caliper piston back in. Then install the new pads and bolt the caliper back on. Be carefull when pressing the piston back in because is might cause your master cylinder to overflow a bit. Once the pads are on the bike, pump the brake a few times until the pedal gets firm. Should be no need to bleed the system as long as you don't open any brake lines.
Hope this helps!

Aug 26, 2010 | 2005 Honda VTX 1300 R

2 Answers

Rear brake pedal goes to the floorboard w/ no resistance,brake ingauges at the bottom but still doesn't feel right.


Check the rear master cylinder for fluid, remove/clean the caliper and any moving components (including rotor, if it's a floating rotor), then bleed the rear brake caliper.

Inspect the pads while you're at it, replace if necessary.

Aug 10, 2010 | 2004 kawasaki VN 800 Vulcan Drifter

1 Answer

Just changed the rear tire and need help getting the rear break back on 1999 heritage softtail


If you have the wheel properly installed, putting the rear brake back on the bike should not be a problem. The brake caliper bracket should act as the wheel spacer on the right side of the bike and must be properly positioned in order to get the axle back in.

With the caliper bracket on the bike, make sure the brake pads are properly positioned in the caliper bracket. Double check to see that the pads are not installed backwards, especially on the back side of the rotor. Carefully, slide the caliper down over the pads, without distrurbing them, and into the caliper bracket. If this is giving you a problem, you may have to press the piston in the caliper back into the the caliper just a bit to clear the pads. If you replaced the pads with new pads, press the piston all the way back into the caliper. I usually use a large pair of slip joint pliers or a large C-clamp to do this with. Make sure you put a rag or something around the caliper to protect the paint. Good Luck!

Dec 27, 2009 | 2000 Harley Davidson FLSTC Heritage...

1 Answer

How to change rear brake pads


Raise the rear of the vehicle and make sure it is securely supported. Remove the rear wheel Remove the brake hose (A) from the suspension arm by removing the brake hose clip (B).Thoroughly clean the outside of the caliper to prevent dust and dirt from entering inside.Support the caliper with a piece of wire so that it does not hang from the brake se.f2d9a24.jpg
Remove the two guide rods (C) and caliper (D) from the bracket. Remove the pad shim (A) and brake pads (B).77fcb0a.jpg

Remove the pad retainers.2884b28.jpg
Clean the caliper thoroughly; remove any rust, and check for grooves and cracks. Check the brake disc for damage and cracks. Install the pad retainers. Check the foreign material at the pad shim (A) and the back of the pads (B). Contaminated brake discs or pads reduce stopping ability. Keep grease off the discs and pads.3fdca95.jpg
Install the brake pads (B) and pad shim (A) on the caliper bracket. Install the inner pad with its wear indicator (C) facing down ward. If you are reusing the pads, always reinstall the brake pads in their original positions to prevent a momentary loss of braking efficiency. Rotate the caliper piston (A) clockwise into the cylinder, the align the cutout (B) in the piston with the tab (C) on the inner pad by turning the piston back. Lubricate the boot with rubber grease to avoid twisting the piston boot. If the piston boot is twisted, back it out so it is positioned properly.1d2811d.jpg
Install the brake caliper (D). Install and torque the guide rods (E) to proper specification. Install the brake hose (F) onto the suspension arm with the brake hose clip (G). After installation, check for leaks at hose and line joints and connections, and retighten if necessary. Depress the brake pedal several times to make sure the brakes work, then test-drive. Engagement of the brake may require a greater pedal stroke immediately after the brake pads have been replaced as a set. Several applications of the brake pedal will restore the normal pedal stroke.

May 31, 2009 | Hyundai Motor 2002 Elantra

1 Answer

How do I fit new brake pads(rear)?


Sorry I don't know how I missed it (rear)
--REAR---  wash the brake assembly  depress the piston using a C-clamp Remove the upper caliper mounting bolt Pivot the caliper down for access to the brake pads Remove the inner brake pad and the outer brake pad Remove the upper and lower pad support plates; make sure they are a tight fit and aren't worn. If necessary replace them Install the brake pads in the caliper mounting bracket pull out the sliding pins, cleanthem, then apply a coat of high-temperature grease to the pins and install them. Replace any boots that are worn or damaged Swing the caliper back into place, install the bolt and tighten 
Caliper mounting bolt torque is 16 to 24 ft-lb rear caliper mounting bracket bolt is 37 to 44 ft-lb

Sep 16, 2008 | 2001 Hyundai Santa Fe

Not finding what you are looking for?
2000 Harley Davidson FXST Softail Standard Logo

292 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

Mike

Level 3 Expert

4340 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...