Question about Motorcycles

Open Question

Yamaha kodiak 400 atv starts & idles fine but wont rev vacuum Throttle 1 not working

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
tattooed780
  • 3 Answers

SOURCE: yamaha big bear 400 atv starts & idles fine but wont rev, sounds like its hitting rev limiter

CLEAN THE JETS AND HAVE THE CARBS SYNCED THAT SHOULD FIX IT

Posted on Apr 20, 2012

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 Yamaha Kodiak 400 4+4 best way to set motor timing and valves


check youtube for generic valve adjusting procedures, the kodiak is like most of them.

Mar 23, 2017 | Yamaha 2004 Kodiak 400 Auto 4x4

1 Answer

98 kodiak 400 4x4 wants to back fire at full throttle choking it helps a little


your carb needs cleaned/adjusted. your float could be set wrong. could be an air leak somewhere.

Dec 30, 2016 | Yamaha 2004 Kodiak 400 Auto 4x4

1 Answer

How to install choke cable on 400 Kodiak atv ?


Your information is on the ATV Forum

Throttle cable: remove the 3 screws on the right side of the carb, take off the cover, there is small rubber gasket (red) Don't lose it. you'll see the cable attached inside. move the mechanism forward like you're opening the throttle to get enough slack to unhook the cable.

Choke: on the other side of the carb, the choke cable screws in with a plastic nut (10 mm i think) unscrew with your hand, if its tight use pliers or wrench..its easy to unscrew it.

throttle choke cable removal Yamaha Grizzly ATV Forum

Sep 12, 2015 | Yamaha Vehicle Parts & Accessories

1 Answer

How do I fix My kodiak 400 that will not shift into reverse or park


as soon as your bike begins to high idle it will not fall into gear you probably will need to set your linkage on your shifte

Sep 01, 2014 | Yamaha 2004 Kodiak 400 Auto 4x4

1 Answer

Yamaha 400 kodiak no spark after washing


you have a open wire or a bad connection the electrical current is grounding either your coil or your kill switch to the fram and not allowing it to start

Aug 01, 2014 | Yamaha 2004 Kodiak 400 Auto 4x4

1 Answer

Kodiak wont start


Run a compression test (3-5 seconds) , with throttle closed, then repeat with throttle open. Should be around 100 psi closed and 125+ with it open. This will give you more direction.

Jul 09, 2014 | ATVs

1 Answer

Engine will not idle when warm, hard to start


There is one screw that adjusts the revs,you can increase the engine revs and it should solve the idling problem.Be careful as there may be one for air mixture which could look similar..make sure you adjust the one for the revs only.If this does not solve your problem then let us know.

Feb 15, 2010 | 2008 Yamaha Yamaha G5

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4525 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...