Question about Motorcycles

Open Question

Can a Ford Bantam 1300 1998 clutch cable be adjusted?

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

alicantecoli
  • 22095 Answers

SOURCE: ford bantam handbrake adjustment

remove the back brake drums ,slacken handbrake cable then run a mini grinder around the lip on the edge of the drum .Then adjust the auto adjusters manully so when the drum is push on it just goes on ,tap with a hammer all around the drum to level the shoes and if need be adjust up a bit more ,then when finished re-adjust the cable so you have three notches on handbrake lever

Posted on May 31, 2010

altomeisters
  • 23 Answers

SOURCE: how do I fix the clutch slave cylinder on a Ford Bantam 1.3 2007?

Hi your ford Bantam clutch slave cylinder fix will require the removal of the transmission , this is a concentric unit incorporated in the release bearing assembly and can only be replaced as a complete unit . if you only have a fluid leak at the connection entering the gearbox you might get a kit at your local dealership, this is for the Rocam Motor driven Bantam
Regards
Faldih Higgins

Posted on Jun 23, 2014

  • 40764 Answers

SOURCE: What's your question? My car is a Ford Bantam pick up van. The model is of 1996. connectin a clutch cable from the gear box to the intrior. Where in the interior is the cable connects.

the clutch pedal up in the pedal mounting bracket

Posted on Jan 01, 2016

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine Torque settings


There are a lot of adjustable torque method, but according to your purpose to distinguish with which kind of appropriate Motor Part Store Motor Parts Wholesale

Jun 26, 2016 | Ford Cars & Trucks

1 Answer

Where are the speed sensor situated on a Ford Bantam 1.6 rocam


It is plugged into the transmission where the speedo cable would go in older cars.

Jun 22, 2016 | 2008 Ford Bantam 1.6i

1 Answer

How to tighten hand brake cable on 2007 Ford Bantam


There may be an adjuter under the car where the two rear cables meet and transition to the single cable going to the pedal.

Aug 08, 2014 | 2007 Ford Bantam 1.3i

1 Answer

Can l kindly have a diagram on how to replace brake shoes on a ford bantam rocam 1.3


Cannot help you here as never seen a bantam but as its a ford i would assume its the same as a ford escort or fiesta ,their not difficult trust me the foreward leading shoe has a leading edge the leading shoe is the thicker one going to the front of the car.the handbrake cable fits to the trailing shoe the one with the arm on for the cable ,the auto adjuster fits just below the slave cylinder with the adjuster to the right or rear of the car smaller spring to the lower and spring with the two coils either end to the top some have a snail cam adjuster some have a little wheel depends on the age of the vehicle ,yes its fiddly but its not a difficult job

Jul 26, 2014 | Cars & Trucks

2 Answers

How do I fix the clutch slave cylinder on a Ford Bantam 1.3 2007?


we replace it when bad. (leaks)
are you asking all steps. R&R

Jun 23, 2014 | 2007 Ford Bantam 1.3i

1 Answer

Ford Bantam rocam Clutch: How do I bleed the clutch?


Clutch bleeding on hydraulic slave cylinders are done in the exact same method as regular hydraulic brakes. If the slave cylinder has a separate reservoir, make sure it is above "MINIMUM" at all times. If it does not have a separate reservoir, then it works together with the master cylinder for the brakes, make sure that one is above minimum too. Pump the clutch pedal a couple of times (note you will rarely feel any resistance in the pedal), hold the pedal down, and have someone open the bleeder valve on the slave cylinder. Close it when no more fluid comes out with pressure, then rinse and repeat until the clutch pedal feels ok.

Jan 09, 2014 | 2006 Ford Bantam 1.6i

2 Answers

Where do i get clutch master cylinder in my ford bantum


Try a used auto parts place. Try Denton Auto Salvage at 785-437-2223

Jan 03, 2014 | 2006 Ford Bantam 1.3i

2 Answers

How to bleed n Clutch system on Ford Bantam 1.3


I have a Ford Bantam 1.3 bakkie and the clutch fluid is running / leaking into the vehicle itself. How do we replace?

May 03, 2012 | 2006 Ford Bantam 1.3i

1 Answer

Ford bantam handbrake adjustment


remove the back brake drums ,slacken handbrake cable then run a mini grinder around the lip on the edge of the drum .Then adjust the auto adjusters manully so when the drum is push on it just goes on ,tap with a hammer all around the drum to level the shoes and if need be adjust up a bit more ,then when finished re-adjust the cable so you have three notches on handbrake lever

May 31, 2010 | 2006 Ford Focus

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75066 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...