Question about Motorcycles

Open Question

Suzuki DS 80 kickstart shaft, I'm replacing the kickstart shaft and I have never done one of these before, any tips or any info that may help me? Would be appreciated

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3567 Answers

SOURCE: How do you remove the kickstart shaft from a1984

Just remove the kick lever then remove the right side cover. This will allow access to the kick start mechanism. Please rate my answer. tombones49_4.png

Posted on Aug 14, 2011

  • 93 Answers

SOURCE: Suzuki ds 80 kickstart shaft

Be sure to get a good look at how the return spring is installed on the old shaft when you remove the cover. Also, be sure to clean all the old gasket material off the case and cover before installing the new gasket.

Posted on Jul 27, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kick start seized


IF YOUR KICKSTART HAS SEIZED AND IT WON'T TILT BACK IN THE PROBLEMS ON THE SHAFT (REMOVE THE DOMED ALAN CAP BOLT THEN REMOVE THE ACTUAL KICKSTART AND CLEAN UP THE SHAFT AND INSIDE DIA OF THE KICKSTART AND LUBE IT BEFORE REFITTING, MIND YOU DON'T LOSE THE SPRING AND BALL). IF ITS SEIZES WHEN YOU KICK THE KICKSTART THEN ITS THE KICKSTART GEAR OR BUSH IN THE SIDE COVER THATS THE PROBLEM. ITS EASY ENOUGH TO CHANGE IF YOU HAVE THE TOOLS FOR THE JOB. IF ITS A DIRT BIKE TRY TO PRESSURE WASH IT THEN SPRAY WITH WD-40 IT MIGHT HELP. GOOD LUCK IF YOU NEED HELP WITH STRIPPING IT DOWN JUST LET ME KNOW (ALSO LET ME KNOW IF ITS A LEFT OR RIGHT SIDE KICKSTART)

Dec 27, 2013 | Gas Gas Motorcycles

1 Answer

Suzuki ds 80 kickstart shaft


Be sure to get a good look at how the return spring is installed on the old shaft when you remove the cover. Also, be sure to clean all the old gasket material off the case and cover before installing the new gasket.

Jul 27, 2013 | Motorcycles

1 Answer

Rg 150 kickstart not returning


The spring must be "wound" to be tight and make the kickstart lever return..

Jul 07, 2017 | 1998 Suzuki RG 150 Gamma

2 Answers

Need to change kick start spring


Hi, i am sorry but you dont say what the model of your machine is, this would help me determing the correct, answers for your questions, most kickstart springs can be changed by simply removing the clutch cover followed by the kickstarter shaft and then replacing the spring, make a note of kickstart stop location carefully remove the shaft holding the gears together replace the spring followed by the. Replacing the shaft and tensioning the spring before cover replacment, oil,etc. Some machines the shaft and spring is inside the centre cases and a complete engine strip is ness

Sep 25, 2011 | kawasaki KX 250 Motorcycles

1 Answer

How do you remove the kickstart shaft from a1984 Suzuki ts185? Is it possible from kickstart side of crankcase or does crankcase need to be split to access from other side?....


Just remove the kick lever then remove the right side cover. This will allow access to the kick start mechanism. Please rate my answer. tombones49_4.png

Aug 14, 2011 | 1981 Suzuki TS 185

1 Answer

I just bought an 1987 Yamaha TT350 dirtbike. is it a 2 cycle and how do i change the kickstart shaft


Hi, a yamaha TT350 actually has a 4 stroke engine. To replace the kick starter shaft, You need to remove the crankcase cover on the kick starter side of the engine..
The clutch basket etc will then have to be removed. '
You then use a set of needle nose pliers to unhook the kickstarter return spring from its post in the crankcase.
Release the return spring and allow it to relax. Then rotate the kickstarter assembly counterclockwise by hand , and remove the shaft assembly from the crankcase. Reverse this process to refit.
You can buy cheap workshop manuals for the yamaha XT/TT 350 models. Clymer manuals make them, there are usually good second hand ones on ebay etc,
the XT/TT350 workshop manual number is
M480-3.
These workshop manuals are a "must have" when working on bikes or cars etc, and by following a manual, at least you'll know that the job has been done safely and 100% correctly.

Apr 01, 2011 | Yamaha TT-R 250 Motorcycles

1 Answer

1995 rm 250 blown water pump seal


Iv'e changed heaps of these.Follow these steps taking carefull note of where & how everything goes to make it easy to put back together. make sketches if necessary.
  • Drain the coolant & engine oil
  • Remove the hoses that go to the water pump
  • remove the waterpump cover
  • remove the impellor
  • remove the kickstarter
  • remove the clutch cover & locating dowel pins if they are still in the clutch cover(if they didn't stay in the crank case)
  • the water pump seal is a (ceramic) two piece unit
  • remove the ceramic disc & rubber holder from the back of the impellor
  • remove the impellor drive shaft from the clutch cover
  • behind the impellor drive shaft there is a small bearing. To remove this I heat around the alloy of the bearing with a heat gun (or butaine gas torch,if using an oxy torch use a small tip & take care to heat evenly & not melt anything/or heat in an oven to 80 to 100 degrees max)Use welding gloves to handle the hot clutch cover)
  • turn the cover over & whack it down on a flat piece of wood(9 times out of 10 this is enough to shock out the bearing
  • remove the back-up seal from behind the bearing you just removed noteing the direction it was facing(for reassembly)
  • now using a suitable drift,knock out the other half of the mechanical seal
  • scrape all the gaskets & clean the parts
  • check the impellor drive shaft to make sure the shaft is smooth & dosn't have any groves worn in it.If it does you'll have to replace it
  • I always fit a new impellor bearing & back-up seal & new gaskets when doing this job
  • reassembly is reverse of removal noting the following
  • to install the bearing & seals use a socket that matches the OUTSIDE diamiter of them so you don't damage them.To install the rubber cup & ceramic washer into the impellor DON'T use a drift just push them in by hand
  • apply some grease to the impellor shaft before installing it
  • Apply some soap to the ceramic disc before re-fitting it
  • to install the clutch cover, if it won't go on at the front near the impellor, turn the impellor shaft to engage the gear
  • refit kickstarter,waterpump cover,hoses
  • re-fill radiator with fresh coolant
  • re-fill gearbox with fresh gearbox oil
That just about covers it all
Hope this helps you
Regards Andrew Porrelli

Dec 03, 2009 | Suzuki RM 250 Motorcycles

1 Answer

My 125dt dosent sart or kick sart,the gear inside have a bushing in shafting?or it was broken..


Common cause of kickstarter not engaging(I am guesing that this is your problem) is a broken spring on the kickstart mechanism,or that the kickstart idler gear cerclip has fallen off(this allows the idler gear to move forward on the shaft & thus won't allow the kickstart gear to transfer drive to the clutch hub).Remove clutch cover, put kickstart lever back on shaft spline,activate kickstart lever by hand(easier with sparkplug removed+in neautral)as kickstart lever moves down 90 degrees the gear on the kickstarter mechanism should move out to engage with gear next to it(kickstart idler gear).If the gear on the kickstarter mechanism dosn't move outward it has a broken spring on the kickstart mechanism.replace spring and all should work.(if the spring is broken you need to try find the broken piece with a magnetic pick-up tool as the broken part can cause further damage if not removed)To do this job I highly recommend you first purchase a workshop manual which will guide you through these processes.After all a manual is the most valuable tool in your tool kit.

Nov 17, 2009 | 2003 Yamaha YZ 125

1 Answer

Suzuki ds 80


Kick Starters on 80CC machines are almost universal. You can look for a Honda or Yamaha and they should fit just make sure that the fitting is the same. Try to expand your search for Suzuki kickstart. good luck

Oct 19, 2008 | Sport & Outdoor - Others

1 Answer

Suzuki tsx 50 motor cycle - kick start problem


You can use a hand heuld grinder and flat top the weld until you can see a visible line all the way around the spine and the lever. Than try tapping lightly. Maybe use a pully puller if it doesn't break free.

Oct 08, 2008 | Welding Tools

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

432 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75051 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...