Question about Harley Davidson XL Sportster 883 Hugger Motorcycles

1 Answer

Hoses connect fuel pump - XL Sportster 883 Hugger Harley Davidson Motorcycles

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Harley Davidson Master
  • 43,092 Answers

Hi Anonymous, it's too bad you can't find the very first and best tool you ever bought for your Harley Davidson. Despair not, for a mere $6.50 you may be able to download another one from the website below and good luck. Harley Davidson Manuals Mark Workshop

Posted on Jun 09, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Do I have to drop the fuel tank to replace the fuel pump on a 94 Buick le saber


Yes ,,instructions are below, Use eye protection for this procedure
Remove or Disconnect:

  1. Relieve Fuel Pressure
  2. Disconnect negative battery cable
  3. Raise vehicle on hoist
  4. Remove Fuel Tank
  5. Remove Fuel Gage sending and pump assembly by turning cam lock ring counterclockwise. Lift assembly from fuel tank and remove fuel pump from fuel gage sender unit.
  6. Disconnect pump wires, hose clamps, and clamp around pump body
  7. Pull pump assembly out of rubber connectors
  8. Inspect fuel pump attaching hose for any signs of deterioration. Replace as necessary.
Install or Connect:

  1. Push fuel pump assembly into attaching hose
  2. Connect pump wires, hose clamps at attaching hose and around pump body
  3. Place Fuel tank sending unit and pump assembly into tank using new O-ring
  4. Place cam lock over assembly and lock by turning clockwise
  5. Install Fuel Tank
  6. Start engine and check fuel pipe connector for visual leaks

Oct 20, 2010 | 1994 Buick LeSabre

1 Answer

Where is the fuel pump located on a 92 Lexus SC300?


Fuel Pump REMOVAL AND INSTALLATION ES300 CAUTION
Fuel injection systems remain under pressure even after the engine has been turned OFF. The fuel system pressure must be relieved before disconnecting any fuel lines. Failure to do so may result in fire and/or personal injury.
  1. Relieve the fuel system pressure.
  2. With the ignition switch in the LOCK position, disconnect the negative battery terminal. If equipped with an air bag system, wait at least 90 seconds or longer before performing any other work.
  3. Remove the rear seat cushion.
  4. Disconnect the fuel pump connector. CAUTION
    The Supplemental Inflatable Restraint (SIR) system must be disarmed before removing the fuel pump. Failure to do so may cause accidental deployment of the air bag, resulting in unnecessary SIR system repairs and/or personal injury.
  5. Remove the floor service hole cover. NOTE: Do not lift the fuel pump assembly up using the wire harness.
  6. Remove the fuel filler cap. Disconnect the fuel outlet pipe and the return hose from the pump bracket.
  7. Remove the 8 screws and lift out the pump/bracket assembly with gasket.
  8. Remove the fuel pump lead wire.
  9. Pull the lower end of the pump off of the bracket.
  10. Disconnect the fuel hose from the pump and remove the pump.
  11. Remove the rubber cushion from the pump. To install:
  12. Install the filter and rubber cushion on the new pump and install the pump on the bracket.
  13. Connect the fuel hose and the wire connector on the pump.
  14. Using a new gasket, install the pump and tighten the eight screws to 35 inch lbs. (4 Nm).
  15. Connect the fuel pipe and return hose to the pump and tighten the bolts to 22 ft. lbs. (29 Nm).
  16. Connect the wire, install the service cover and replace the rear seat.
  17. Connect the negative battery cable.
  18. Start the engine and check for leaks. Fig. 1: Fuel pump assembly - ES300 294126.gif
GS300, LS400, SC300 and SC400
  1. Disconnect the negative battery cable. Wait at least 90 seconds before performing any other work.
  2. Remove the trunk floor mat.
  3. Remove the trunk trim cover.
  4. Disconnect the fuel pump electrical connector.
  5. Remove the rear seat bottom and seat back.
  6. Remove the partition cover.
  7. Remove the mounting bolts and remove the fuel pump set plate.
  8. Remove the three nuts and disconnect the fuel pump bracket from the tank.
  9. Disconnect the fuel hose from the bracket. Remove the pump, bracket and set plate as an assembly. To install:
  10. Install a new gasket on the set plate. Connect the fuel hose to the pump and bracket,
  11. Install the pump and bracket assembly with the three nuts; tighten the nuts to 48 inch lbs. (5 Nm). Install the set plate and tighten the bolts to 26 inch lbs. (3 Nm).
  12. Install the panel partition
  13. Install the rear seat cushion and back.
  14. Connect the fuel pump electrical connector.
  15. Install the trim panel.
  16. Install the spare tire and the trunk floor mat.
  17. Connect the negative battery cable.
  18. Start the engine; check the fuel system for leaks
  19. Road test the vehicle for proper operation.

Oct 13, 2010 | 1992 Lexus Sc 300

1 Answer

Access panel for fuel pump


There is none:

Fuel Tank & Fuel Pump Module Assembly Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Shift the vehicle into NEUTRAL and position it on a hoist.
  3. Release the fuel pressure.
  4. Disconnect the negative battery cable.
  5. Remove the fuel tank filler cap.
  6. Drain as much fuel from the tank as possible.
  7. Using suitable hose pinching pliers, clamp the fuel tank filler hose. Clamp the fuel tank filler hose in the location shown ford-05-00-396.gif

  8. Disconnect the three quick connect couplings from the fuel tank tubes at the tank.
  9. Disconnect the fuel pump electrical connector.
  10. Disconnect the fuel filter inlet tube from the filter.
  11. Position a suitable lifting device under the fuel tank.
  12. Remove the two fuel tank support strap bolts.
  13. Lower the fuel tank to access the fuel pump module while swinging the fuel tank support straps away from the tank.
  14. Clean the area around the fuel pump mounting flange.
  15. Disconnect the fuel pump module electrical connector and the fuel pump module fuel outlet tube.
  16. Using the special tool, turn the fuel pump module retaining ring counterclockwise and remove it. CAUTION
    The fuel pump module must be handled carefully to avoid damage to the float arm, filter and convolute hoses.
  17. Turn the fuel pump module counterclockwise and the fuel pump module will release from the locking tabs. Remove the fuel pump module from the fuel tank.
To Install:
  1. Install the fuel pump module in the fuel tank.
  2. Connect the fuel pump module electrical connector and the fuel pump module fuel outlet tube.
  3. Raise the tank into position and install the mounting strap bolts. Tighten the bolts to 26 ft-lbs (35 Nm).
  4. Connect the fuel lines and electrical connectors at the fuel tank.
  5. Lower the vehicle and refill the tank.
  6. Connect the negative battery cable.
  7. Turn the ignition key to the ON position to pressurize the fuel system.
  8. Visually inspect the fuel system for leaks.
prev.gif next.gif

Oct 05, 2010 | 2000 Ford Taurus

1 Answer

I need a diagram to replace a fuel tank on a 1987 vw cabriolet


1987 Volkswagen Cabriolet 1.8L FI SOHC 4cyl

1985-89 Scirocco and Cabriolet
  1. Disconnect the negative battery cable and drain the fuel tank.
  2. Remove the rear right wheel housing cover.
  3. Disconnect the large breather hose from the filler neck.
  4. Pull the gravity valve down leaving the hoses connected.
  5. Unbolt the fuel pump bracket from the body and lower the pump.
  6. Remove the fuel tank screw.
  7. Disconnect the fuel pump hose and pull the blue hose from the return line.
  8. Disconnect the brake hoses from both sides of the rear axle and plug them.
  9. Disconnect the rear axle from both sides of the body and allow it to swing down and rest on the handbrake cable guides.
  10. Unhook the rear muffler support lugs.
  11. Disconnect the filler hose from the tank.
  12. Support the tank, remove the tank fasteners and lower the tank enough to disconnect the fuel gauge sending unit wires and breather hoses.
  13. Remove the fuel tank.

To install:
If installing a new or used tank, make note of where the old foam strips were installed, and install new foam strips on the replacement tank in the same locations.
  1. Raise and support tank. Connect the small breather hoses and fuel gauge sending unit wires. Install the tank fasteners.

When connecting the breather hoses, position the hose clips so that they do not make contact with the body.
  1. Connect the filler hose to the tank and connect the rear muffler support lugs.
  2. Raise the rear axle off the handbrake cable guides and install.
  3. Connect the brake hoses and bleed the brakes.
  4. Connect the return line and fuel pump hose.
  5. Install the fuel tank screw.
  6. Raise the fuel pump and attach the fuel pump bracket to the body.
  7. Put the gravity valve back into its original (raised) position.
  8. Connect the large breather hose to the filler neck.

When connecting the breather hose, position the hose clip so that it does not make contact with the body.
  1. Install the right rear wheel housing cover.
  2. Fill the tank and connect the negative battery cable.

40071b2.jpg

Fig. 1: Fuel tank assembly used on the Rabbit Pick-up. Other models are similar

Hope helps (remember to rate and comment this).

Sep 21, 2010 | Volkswagen Cabriolet Cars & Trucks

2 Answers

How do u get the fuel pump on


Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Shift the vehicle into NEUTRAL and position it on a hoist.
  3. Release the fuel pressure.
  4. Disconnect the negative battery cable.
  5. Remove the fuel tank filler cap.
  6. Drain as much fuel from the tank as possible.
  7. Using suitable hose pinching pliers, clamp the fuel tank filler hose. Clamp the fuel tank filler hose in the location shown ford-05-00-396.gif

  8. Disconnect the three quick connect couplings from the fuel tank tubes at the tank.
  9. Disconnect the fuel pump electrical connector.
  10. Disconnect the fuel filter inlet tube from the filter.
  11. Position a suitable lifting device under the fuel tank.
  12. Remove the two fuel tank support strap bolts.
  13. Lower the fuel tank to access the fuel pump module while swinging the fuel tank support straps away from the tank.
  14. Clean the area around the fuel pump mounting flange.
  15. Disconnect the fuel pump module electrical connector and the fuel pump module fuel outlet tube.
  16. Using the special tool, turn the fuel pump module retaining ring counterclockwise and remove it. CAUTION
    The fuel pump module must be handled carefully to avoid damage to the float arm, filter and convolute hoses.
  17. Turn the fuel pump module counterclockwise and the fuel pump module will release from the locking tabs. Remove the fuel pump module from the fuel tank.
To Install:
  1. Install the fuel pump module in the fuel tank.
  2. Connect the fuel pump module electrical connector and the fuel pump module fuel outlet tube.
  3. Raise the tank into position and install the mounting strap bolts. Tighten the bolts to 26 ft-lbs (35 Nm).
  4. Connect the fuel lines and electrical connectors at the fuel tank.
  5. Lower the vehicle and refill the tank.
  6. Connect the negative battery cable.
  7. Turn the ignition key to the ON position to pressurize the fuel system.
  8. Visually inspect the fuel system for leaks.
prev.gif next.gif

Aug 19, 2010 | 2001 Ford Taurus

1 Answer

Location of fuel pump for 1992 subaru loyale wagon


REMOVAL & INSTALLATION

See Figure 1


0900c15280067055.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 1: Fuel pump assembly mounted under the vehicle-1.8L engine
  1. Release the fuel system pressure. Do not reconnect the fuel pump harness.
  2. Disconnect the negative battery cable.
  3. Raise and support the vehicle safely on jackstands.
  4. Clamp the middle portion of the hose connecting the fuel tank pipe and the pump to prevent fuel from flowing out of the tank when unfastened.
  5. Loosen the hose clamp and disconnect the hose.
  6. Remove the three pump bracket mounting bolts and remove the pump together with the pump damper.

To install:
  1. Install the fuel pump and damper, and tighten the bolts securely.
  2. Install the hose and tighten the clamp screw to 9-13 inch lbs. (1.0-1.5 Nm).
  3. Install the pump bracket in position to the vehicle body and secure it with the bolts.

Take care to position the rubber cushion properly.
  1. Connect the pump harness.
  2. Connect the negative battery cable and test the fuel pump for proper operation.
  3. Check for fuel leaks.

TESTING

  1. Turn the ignition ON and listen for the fuel pump to make a growling sound. Turn the ignition OFF .
  2. Release the fuel system pressure. Disconnect the pump harness and crank the engine for 5 seconds or more. If the engine starts, allow it to run until it stops. Turn the ignition OFF and install the fuel pump connector.
  3. Disconnect the fuel hose at the fuel pump.
  4. Connect a gauge in-line using a T-fitting.
  5. Start the engine and measure the fuel pressure. If the fuel pressure is not 36-50 psi (248-344 kPa), replace the pump.
  6. Release the fuel system pressure and remove the gauge.

May 22, 2010 | 1992 Subaru Loyale

1 Answer

How to remove fuel filter housing 97 ford f-350


FIRST YOU NEED A SUITABLE CONTAINER.PLACE UNDER FILTER DRAIN HOSE OPEN THE FILTER DRAIN.NOW YOU HAVE TO REMOVE THE TURBOCHARGER ASSEMBLY.REMOVE THE THE BAFFLE AND THE AIR INLET CROSSOVER MANIFOLD.REMOVE THE TWO CAPSCREWS SECURING THE FUEL FILTER BASE TO THE CRANLCASE.DISCONNECT THE WATER DRAIN HOSE FROM FILTER. DISCONNECT THE FUEL OUTLET HOSE LOCATED BETWEEN THE FUEL AND FILTER HOUSING.AND THE FUEL RETURN HOSE FROM THE FUEL PRESSURE REGULATOR VALVE.DISCONNECT THE TWO FUELSUPPLY HOSES THAT CONNECT THE REGULATOR BLOCK TO THE CYLINDER FUEL RAILS.LOOSEN THE CLAMP AT THE FUEL PUMP END OF THE HOSE WHICH CONNECTS THE FUEL FILTER TO THE INLET OF HIGH PRESSURE STAGE AT THE FUEL PUMP.DISENGAGE THE WIRING HARNESS FROM THE RIGHT SIDE OF THE FILTER HOUSING.DISENGAGE THE ELECTRICAL CONNECTIONS FROM THE WATER IN FUEL SENSOR AND THE FUEL HEATER.REMOVE THE FUEL FILTER.USE A PRYBAR TO REMOVE THE FUEL FILTER CAP AND THE FILTER ELEMENT WILL COME OUT WITH THE CAP.DEPRESS THE ELEMENT LOCKING TABS AND REMOVE THE ELEMENT FROM THE CAP.TO INSTALL CLEAN THE MATING SURFACES AND INSTALL THE FILTER ELEMENT ONTO THE CAP MAKING SURE THE TABS ENGAGE.INSTALL THE FILTER CAP AND PRESS DOWN FIRMLY BUT GENTLY TO ENGAGE IT.ENGAGE THE WIRING CONNECTIONS TO THE FUEL HEATER AND WIF SENSOR.ENGAGE THE WIRING HARNESS TO THE FILTER HOUSING.TIGHTEN THE CLAMP AT THE FUEL PUMP END OF HOSE WHICH CONNECTS THE FUEL FILTER TO THE INLET OF HIGH PRESSURE STAGE AT THE FUEL PUMP.ENGAGE THE TWO FUEL SUPPLY HOSES THAT CONNECT THE REGULATOR BLOCK TO THE CYLINDER HEAD FUEL RAILS.CONNECT THE FUEL OUTLET HOSE LOCATED BETWEEN THE FUEL AND FILTER HOUSING AND THE FUEL RETURN HOSE FROM THE FUEL PRESSURE REGULATOR VALVE.CONNECT THE WATER DRAIN HOSE TO THE FILTER.INSTALL THE 2 CAP SCREWS SECURING THE FUEL FILTER BASE TO THE CRANKCASE.INSTALL THE AIR INLET CROSSOVER MANIFOLD AND BAFFLE.INSTALL THE TURBOCHARGER ASSEMBLY.

Apr 03, 2010 | 1997 Ford F350 Crew Cab

2 Answers

HOW TO REPLACE A FUEL PUMP FOR A NISSAN XTERRA



Removal & Installation

  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Relieve the fuel system pressure.
  3. Drain the fuel tank.
  4. Remove or disconnect the following:

    Negative battery cable Fuel pump module harness connectors Filler hose shield Fuel pressure and return lines Filler hose Vent hose Evaporative Emissions (EVAP) hose Fuel tank skid plate Fuel tank Fuel level sender Fuel pump

To install:
  1. Install or connect the following:

    Fuel pump Fuel level sender. Tighten the screws to 17-23 inch lbs. (2.0-2.5 Nm). Fuel tank. Tighten the bolts to 27-36 ft. lbs. (37-49 Nm). Fuel tank skid plate. Tighten the bolts to 27-36 ft. lbs. (37-49 Nm). EVAP hose Vent hose Filler hose Fuel pressure and return lines Filler hose shield Fuel pump module harness connectors Negative battery cable
  2. Fill the fuel tank.
  3. Start the engine and check for leaks.

Mar 31, 2010 | 2005 Nissan Xterra

1 Answer

How to replace fuel pump 91 lesabre


Removal & Installation The fuel pump is located in the fuel tank. The fuel tank must be removed from the vehicle in order to access the pump.
  1. Properly relieve fuel system pressure.
  2. If not already done, disconnect the negative battery cable.
  3. Raise and safely support the vehicle.
  4. Safely drain and remove the fuel tank assembly, as outlined later in this section.
  5. If necessary, detach the quick-connect fittings from the fuel sender assembly and remove the fuel lines.
  6. Remove the fuel gauge sender and pump assembly by turning the cam locking ring counterclockwise. It may be necessary to use a spanner wrench, such as tool J-24187, to perform this.
  7. Carefully lift the assembly from the fuel tank, then remove the fuel pump from the fuel gauge sender unit.
  8. Remove the sender O-ring from the top of the sender and discard.
  9. Disconnect the pump wires, hose clamps and the clamp from around the pump body.
  10. Pull the pump assembly out of the rubber connectors.
  11. Inspect the fuel pump attaching hose for any signs of deterioration, and replace as necessary.
  12. To install:
    1. Push the fuel pump assembly into the attaching hose. Attach the pump electrical wires and fasten the hose clamps to the attaching hose and around the pump body.
    2. Place the fuel tank sender and pump assembly into the fuel tank. Use a new O-ring seal during assembly.
    3. Place the cam lock over the assembly, then lock by turning clockwise, using a suitable spanner wrench, if necessary.
    4. If removed, attach the fuel sender fuel line quick-connect fittings.
    When installing the fuel tank, make sure all rubber sound isolators or anti-squeak spacers are replaced in their original locations.
    1. Install the fuel tank, as outlined later in this section.
    2. Refill the fuel tank.
    3. Connect the negative battery cable.
    4. Turn the ignition switch to the ON position to pressurize the fuel system and check for leaks.

Oct 10, 2009 | 1991 Buick LeSabre

2 Answers

1999 jeep cherokee do you have to remove the fuel pump to replace


The combination Fuel Filter/Fuel Pressure Regulator is located on the fuel pump module. The fuel pump module is located on top of fuel tank.

The filter/regulator may be removed without removing fuel pump module although fuel tank must be removed.

REMOVAL
  1. Remove fuel tank. Refer to Fuel Tank Removal/Installation.
  2. Clean area around filter/regulator.
  3. Disconnect fuel line at filter/regulator. Refer to Quick-Connect Fittings for procedures.
  4. Remove retainer clamp from top of filter/regulator. Clamp snaps to tabs on pump module. Discard old clamp.
  5. Pry filter/regulator from top of pump module with 2 screwdrivers. Unit is snapped into module
  6. Discard gasket below filter/regulator.
    1. Before discarding filter/regulator assembly, inspect assembly to verify that O-rings are intact. If the smallest of the two O-rings can not be found on bottom of filter/regulator, it may be necessary to remove it from the fuel inlet passage in fuel pump module.
    INSTALLATION
    1. Clean recessed area in pump module where filter/regulator is to be installed.
    2. Obtain new filter/regulator (two new O-rings should already be installed)
    3. Apply a small amount of clean engine oil to O-rings. Do not install O-rings separately into fuel pump module. They will be damaged when installing filter/regulator.
    4. Install new gasket to top of fuel pump module.
    5. Press new filter/regulator into top of pump module until it snaps into position (a positive click must be heard or felt).
    6. The arrow molded into top of fuel pump module should be pointed towards front of vehicle (12 O'clock position).
    7. Rotate filter/regulator until fuel supply tube (fitting) is pointed towards front of vehicle (12 O'clock position).
    8. Install new retainer clamp (clamp snaps over top of filter/regulator and locks to flanges on pump module).
    9. Connect fuel line at filter/regulator. Refer to Quick-Connect Fittings for procedures.
    10. Install fuel tank. Refer to Fuel Tank Removal/Installation.
WARNING: THE FUEL SYSTEM IS UNDER CONSTANT FUEL PRESSURE EVEN WITH THE ENGINE OFF. THIS PRESSURE MUST BE RELEASED BEFORE SERVICING FUEL TANK .

Two different procedures may be used to drain fuel tank (lowering tank or using DRB scan tool).

The quickest draining procedure involves lowering the fuel tank.

As an alternative procedure, the electric fuel pump may be activated allowing tank to be drained at fuel rail connection. Refer to DRB scan tool for fuel pump activation procedures. Before disconnecting fuel line at fuel rail, release fuel pressure. Refer to the Fuel System Pressure Release Procedure for procedures. Attach end of special test hose tool number 6541, 6539, 6631 or 6923 at fuel rail disconnection (tool number will depend on model and/or engine application). Position opposite end of this hose tool to an approved gasoline draining station. Activate fuel pump and drain tank until empty.

If electric fuel pump is not operating, tank must be lowered for fuel draining. Refer to following procedures.

FUEL TANK REMOVAL
  1. Disconnect negative battery cable at battery.
  2. Release fuel system pressure. Refer to the Fuel System Pressure Release.
  3. Raise and support vehicle.
  4. If Equipped: Remove fuel tank skid plate.
  5. Remove 4 fuel hose shield mounting bolts and remove fuel hose shield from body.
    1. Remove fuel tank fill hose and vent hose clamps at fuel tank filler tube. Remove both hoses at fuel filler tube.
    2. Remove exhaust tailpipe heat shield mounting bolts and remove shield. CAUTION: To protect fuel tank from exhaust heat, this shield must reinstalled after tank installation.
    3. Place a hydraulic jack to bottom of fuel tank. WARNING: PLACE A SHOP TOWEL AROUND FUEL LINES TO CATCH ANY EXCESS FUEL .
      1. Disconnect fuel supply line from fuel extension line near front of fuel tank. Refer to Fuel Tubes/Lines/Hoses and Clamps. Also refer to Quick-Connect Fittings for procedures.
      2. Disconnect EVAP canister vent line near front of tank.
      3. Disconnect fuel pump module electrical connector (pigtail harness) near front of tank. Harness connector is clipped to body.
        1. Remove two fuel tank strap nuts. Position both tank support straps away from tank.
        2. Carefully lower right side of tank while feeding both fuel hoses through access hole in body. Fuel Tank Full And Not Drained Using DRB Scan Tool: To prevent fuel loss through hoses, keep left side of tank higher than right side while lowering. Do not allow hose openings to drop lower than top of tank.
        3. Continue lowering tank until clear of vehicle. Place tank on floor with left side (hose side) higher than right side
          1. Drain tank by removing fuel fill hose at tank. Fuel fill hose is largest of 2 hoses. Insert the drain hose (from an approved gasoline draining station) into hose opening. Drain tank until empty.
          2. If fuel pump module removal is necessary, refer to Fuel Pump Module Removal/installation for procedures.
          INSTALLATION
          1. If fuel pump module is being installed, refer to Fuel Pump Module Removal/installation for procedures.
          2. Install fuel fill/vent hoses to tank fittings. To prevent hose from kinking, rotate each hose until index mark on hose is aligned to index tang on fuel tank.
          3. Install hose clamps to hoses. Position clamps between index marks on each hose.
          4. Position fuel tank to hydraulic jack.
          5. Raise tank into position while guiding fuel fill and vent hoses into and through access hole in body.
          6. Continue raising tank until positioned to body.
          7. Attach two fuel tank mounting straps and mounting nuts. Tighten nuts to 10 Nm (90 in. lbs.) torque. Do not over tighten nuts.
          8. Install both fuel hoses to fuel fill tube. Tighten both retaining clamps.
          9. Position fuel hose shield to body. Install and tighten 4 mounting bolts.
          10. Connect fuel pump module pigtail harness electrical connector near front of tank.
          11. Connect fuel pump module supply line near front of tank. Refer to Quick-Connect Fittings for procedures.
          12. Connect EVAP hose near front of tank.
          13. Install exhaust tailpipe heat shield.
          1. Install fuel tank skid plate (if equipped).
          1. Lower vehicle and connect battery cable to battery.

Feb 08, 2009 | 1999 Jeep Cherokee

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

Mike

Level 3 Expert

4340 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...