Question about 2011 Xingyue Xy150T6

1 Answer

Exhaust pipes my scooter got an exhaust leak making it very loud you can hear it is coming from the front of the engine. i replaced the gasket but did not help i even made header style gasket in addition to the factory gasket and it is still loud any ideas?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 4 Answers

I would try muffler weld its 5$ at autozone if that dosent help i would get the leak welded shut

Posted on Jul 28, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My van is now starting to sound like a tractor


Check your exhaust system for leaks holes in the pipes or gasket problems at pipe connections and exhaust maniflod It won't be loud if the problem is befind the muffler in front it will be .You can usauly feel the exhuast comeing out if you cheak it right after you start the engine and the pipes are still cold because the exhauts will be hot . Try to pin point ware the noise is comeing from first like the day before .Don't get burned these things get vary hot

Apr 18, 2012 | 2003 Dodge Grand Caravan AWD

1 Answer

I got a 1999 gmc sonoma 4.3 v6 vortec I have strong exhaust fumes coming threw the a/c vents while the a/ is on


You have a leak in the exhaust system. Have it looked at soon. You don't want to be breathing carbon monoxide while driving. If you hear a "ticking" sound while the engine is running (more predominant with a cold engine) it's most likely an exhaust manifold leak, either a bad gasket, broken stud or cracked manifold. Other possible causes could be the "donut" gaskets that seal the Y pipe to the exhaust manifolds, the Y pipe to catalytic converter gasket (if equipped).

Mar 19, 2011 | GMC Sonoma Cars & Trucks

1 Answer

2003 dodge ram 1500 5.7 hemi replaced piston and head now have tapping noise from front of engine. sounded like exhuast leak replaced gasket. not loud at idle but when start driven gets loud.


Could be a bad gasket tightness if you replaced the gasket. The exhaust manifold could be not torqued down evenly causing a gap to exist allowing exhaust gas vapor and sound to escape at the cylinder head connection.

Dec 18, 2010 | Dodge Ram 1500 Cars & Trucks

1 Answer

Exaught manafold leak


You state that car makes a loud noise when driving. Do you notice the sound more when you accelerate? If yes, then it could be either the exhaust manifold gasket or the donut gasket. The donut gasket is where the exhaust pipe connects to the exhaust manifold.

Jun 24, 2010 | 2000 Ford Focus

2 Answers

How do i find where an exhust leak is coming


check where the headers come off of the engine exhaust leaks are generally quite loud and you will either be at the headers/exhaust manifold or just as you come off that bend there will be a flange gasket inside the two pipes joining. from the bend to the straight pipe just as it passes the gearbox and starts to straighten out.

Jun 22, 2010 | 1996 Chevrolet S-10 Pickup

1 Answer

Have a 1999 eclipse 2.0 L...Need to replace oil pan. Do I have to remove any other parts to get the pan off


2.0L Engine
  1. Disconnect the negative battery cable.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Engine undercover Front exhaust pipe Lower oil pan bolts and lower pan Cover Upper oil pan bolt and upper pan Baffle plate

    0996b43f8023193a.jpg Fig. Oil pan and related components-2.0L engine

To install:
  1. Clean all gasket surfaces of the cylinder block and the upper and lower oil pan.
  2. Install or connect the following:
    Baffle plate
  3. Apply a 0.16 in. (4mm) bead of sealant to the gasket surfaces of the upper oil pan.
    Upper oil pan onto the cylinder block within 15 minutes after applying sealant. Tighten the bolts as shown in the accompanying figure.

    0996b43f8023192d.jpg Fig. Upper oil pan bolt location and torque sequence-2.0L engine

  4. Apply 0.16 in. (4mm) bead of sealant to the gasket surfaces of the lower oil pan.
    Lower oil pan and tighten the bolts, in the sequence shown, to 88-106 inch lbs. (10-12 Nm)

    0996b43f8023192e.jpg Fig. Lower oil pan bolt tightening sequence-2.0L engine
    Front exhaust pipe Engine undercover Oil drain plug with a new gasket and tighten to 29 ft. lbs. (40 Nm)

    0996b43f8023192f.jpg Fig. Make sure to the install the new drain plug gasket as shown, or leaks will occur

  5. Lower the vehicle and fill the crankcase to the proper level with clean engine oil.
  6. Connect the negative battery cable. Start the engine and check for leaks.
Non-Turbo Engine
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Drain the engine oil into a suitable container.
  4. Once the oil has completely drained, install the plug and tighten to 25 ft. lbs. (34 Nm).
  5. Remove the front exhaust pipe.
  6. Remove the engine oil dipstick and tube assembly.
  7. Remove the front plate.
  8. Unfasten the oil pan mounting bolts, then remove the oil pan and gasket.

    0996b43f80222121.jpg Fig. Exploded view of the oil pan and related components-1999 2.0L non-turbo engine

To install:
  1. Apply sealant at the point where the engine block meets the oil pump.
  2. Use a new gasket and install the oil pan. Tighten the mounting bolts to 8.9 ft. lbs. (12 Nm).
  3. Install the front plate.
  4. Install the front exhaust pipe.
  5. Install the dipstick and tube assembly.
  6. Safely lower the vehicle to the floor.
  7. Refill the crankcase with oil to the proper level.
  8. nnect the negative battery cable.
  9. Start the engine and check for leaks.

Turbo Engine
  1. Disconnect the negative battery cable.
  2. Safely raise and support the vehicle.
  3. Remove the front exhaust pipe.
  4. Remove the exhaust pipe and muffler assembly.
  5. Drain the engine oil into a suitable container. Once the oil has drained completely, tighten the plug to 29 ft. lbs. (39 Nm).
  6. Remove the dipstick and tube.
  7. For AWD vehicles, remove the transfer case assembly as follows:
    1. With the propeller shaft still installed, remove the transfer mounting bolt.
    2. Insert a suitable prytool in between the transfer case and transaxle, then remove the transfer case from the center shaft.
    3. Remove the transfer case from the center shaft. Do NOT tilt the transfer assembly to the rear or oil will leak out.
    4. After removing the transfer assembly, insert tool MB991193 or equivalent, to prevent the oil from leaking out. Use a piece of wire to suspend the transfer case from the body.

      0996b43f80222122.jpg
      Fig. View of the transfer case with the tool installed to prevent oil from leaking out-1999 2.0L turbo engines
  8. Remove the bell housing cover.
  9. Disconnect the oil return pipe from the oil pan.
  10. Remove the oil pan mounting bolts. Tap the oil pan seal breaker MB998727 or equivalent between the oil pan and the engine block to break the seal and remove the oil pan.

    0996b43f80222123.jpg Fig. Exploded view of the oil pan and sealant application-1999 2.0L Turbo engine

To install:
  1. Clean the sealing surface on the oil pan and engine block. Apply a continuous bead of sealant MD970389 or equivalent to the oil pan.
  2. Clean the oil pan mounting bolt holes in the oil seal case.
  3. Install the oil pan to the engine block. Tighten the mounting bolts to 5.1 ft. lbs. (6.9 Nm).
  4. Use a new gasket and connect the oil return pipe to the oil pan.
  5. Install the bell housing cover.
  6. If equipped with AWD, install the transfer case assembly.
  7. Install the dipstick and tube assembly.
  8. Install the front exhaust pipe.
  9. Install the exhaust pipe and muffler.
  10. Install a new oil filter.
  11. Safely lower the vehicle to the floor and add five quarts of oil to the crankcase.
  12. Connect the negative battery cable.
  13. Start the engine and check for leaks.

Good luck (remember rated this help).

Mar 06, 2010 | 1999 Mitsubishi Eclipse

1 Answer

Black smoke front engine on motorbike


check valve cover is it leaking oil. clean up the engine real good....i use chemtool B-12 carb cleaner.. wear gloves and don't breathe the fumes and if it gets on the exhaust, you"ll see smoke come off the pipes, so let it dry up before riding and wipe the exhaust pipes real good...now ride the bike and see if you see any smoke...when you do, pull over and take a look to see where its coming from...it could also be coming from a leaking exhaust pipe gasket.

Oct 02, 2009 | 2002 Triumph TT 600

2 Answers

Loud muffler noise up front of vehical.what is


If the noise sounds like your muffler, but isn't coming from the area of your muffler, then you have an exhaust leak upstream from the muffler.

From the front of your muffler, follow the tubing forward to the catalytic converter, then forward to the engine exhaust manifold.

If you start with the car sitting for a few hours to make sure it's cold, you can use your hand to feel for blowing leaks while the engine is running, but chances are you'll be able to hear it. be careful of the catalytic converter itself, as it heats up fast, so check that first.

Once you've found the leak, the fix depends on the emissions laws in your state. If you have none, and the leak is in the middle of the pipe, you can buy pipe patchers (metal preferred) through auto parts stores or catalogs/websites. If you have strict emissions laws, or the leak is at the junction of the catalytic converter and pipe, you'll need to replace the failing part.

Jun 26, 2009 | 1993 Toyota Camry V6

4 Answers

Still loud


Have you checked the flex pipe section under the engine, and the gasket between the manifold and cat/flex pipe section? Those are two places they usually start to leak from either a blown gasket, or the flex section rusts out under the protective covering.

Mar 24, 2009 | 1998 Saturn SL

1 Answer

I have a exhaust leak on the pasanger side


With the engine cold, start and have your helper hold a bunched up rag over the exhaust pipe. You will spot the leak in seconds! Frankster016

Nov 26, 2008 | 1985 Ford Thunderbird

Not finding what you are looking for?
2011 Xingyue Xy150T6 Logo

Related Topics:

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top Xingyue Experts

bobwin

Level 2 Expert

58 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gregg Mahin
Gregg Mahin

Level 3 Expert

39932 Answers

Are you a Xingyue Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...