Question about Motorcycles

Open Question

Road glide volt gauge bulb replacement - Motorcycles

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3230 Answers

SOURCE: Do I need to remove my fairing to replace the headling bulbs?

Hi there,

well you can please follow the below steps -

Remove the Fairing - 1. Unscrew all seven outer fairing fasteners using a Torx driver. These screws are located on the inner fairing near the windshield, the speakers, and the handlebar clamps.
2. Stand in front of the motorcycle. Tilt the outer fairing toward you and hold it firmly. Reach in and disconnect the wire connectors for the headlight assembly by hand.
3. Move the fairing to a work bench to continue the procedure.

Change the Headlights - 1. Remove the wire harness connectors from the back of each headlight that need replacement. Turn the plastic retainer counterclockwise by hand to remove each bulb from its housing.
2. Install the new headlight bulb or bulbs, with each bulb's wider ears on the bulb back plates oriented toward the top. Screw in the plastic retainer rings by hand.
3. Connect the headlight wire harness connectors to the back of each headlight.
4. Move the fairing back to the motorcycle. Reinstall the fairing, battery and seat in reverse order.
Please post comments if you need more help or information.........

Good Luck!!

Thanks

Posted on Mar 17, 2010

  • 302 Answers

SOURCE: 2000 HD Road Glide Alternator replacement

Before you spend for the new alternator, look for loose or dirty connectors. That's common on large twins.
You gave us no idea of automotive/Bike/Repair skills, so I don't know how easy/Hard it will be for you.

Posted on May 03, 2010

bdrew1340
  • 448 Answers

SOURCE: Do I need to remove the fairing on my 2008 Road Glide/FLTR to replace the headlight bulbs?

Nope, only access is from the back, inside the fairing. Sorry!

Posted on Jul 13, 2012

  • 2 Answers

SOURCE: My instruments wont work on

Harden is right, it is best to carry a few 10a & 15a fuses, the instruments require a 15a fuse. Disconnect the battery before replacing, but be sure to deactivate the TSSM before the battery and then replace the fuse. It would be wise to follow the wires for the blown fuse, the fuse blew for a reason which is usually a good indicator that something is not right, unless you know of any type of reason for an isolated power surge / short in the system. I have a 2002 FLTR that I got for my Dad and he had the same issue. I have a 2011 FLTRUSE and haven't had this problem yet. I would strongly suggest obtaining a service manual. It cost 60 bucks for for the 2011 at HD, but my pops got his from CLYMER, just add dot.com to Clymer and it was less than half of what I paid, (actually my wife bought it for me). Good luck ...

Posted on Mar 09, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fuel level gauge not working how to check voltage


Hi Anonymous, have you fuel gauge sending unit checked out and wiring for power to it should be 12 volts.Good luck

Nov 21, 2013 | 2001 Harley Davidson FLHT Electra Glide...

1 Answer

Fuel gauge is pegged to empty on 09 street glide


Don't know if it's the same routine, but here's the troubleshooting for a 2009 Road King:

Disconnect harness from fuel gauge
Turn ignition switch to IGN. Check for voltage at terminal 1 of fuel gauge connector.

If no voltage, repair the break.

If voltage present, disconnect harness connector from speedometer.
Check for continuity between terminal 9 of speedometer connector and terminal 2 of fuel gauge connector.

If no continuity, repair the break

If there is continuity, check resistance to ground on yellow/white wire in speedometer connector.

If less then 10 Ohms, go to item #1
If more then 10 Ohms, go to item #2

item #1:
Disconnect the fuel pump/level sending connector from the sender.
Check for continuity between terminal "A" of the connector and ground.

If continuity is present, locate and repair short to ground.
If continuity is not present, replace the fuel level sender.


item #2:
Greater then 10 Ohms resistance:
Reconnect fuel gauge connector to the gauge.
Turn ignition switch to IGN.
Check for voltage on terminal "9" of the speedometer connector.

If voltage is present, replace the speedometer.
If voltage is not present, replace the fuel gauge.


Hope this helps!

Nov 26, 2012 | 2009 Harley Davidson FLHX Street Glide

1 Answer

What should the voltage gauge read on my 97 electraglide ultra fuel injected


Hi Cyrcleme, with the switch on between 12-12.5 volts. Driving down the road 14.3-14.7 volts. Have nice day.

Mar 01, 2012 | 2000 Harley Davidson FLHTCUI Electra Glide...

1 Answer

My 2000 harly davidson electra glide classic speedometer goes up and down wiel riddin and then stoped working


need to check volt gauge, should be about 13.8. if it's overcharging it will cause it to jump around. Check volts above 2500 rpm

Sep 12, 2010 | 2000 Harley Davidson FLHTCUI Electra Glide...

1 Answer

Check engine light came on as my volt gauge went from 14 to 11


check wiring loom to alternator,bat connections or lack of volts from alternator

Jul 03, 2010 | 2003 Harley Davidson FLHTCUI Electra Glide...

1 Answer

2000 HD Road Glide Alternator replacement


Before you spend for the new alternator, look for loose or dirty connectors. That's common on large twins.
You gave us no idea of automotive/Bike/Repair skills, so I don't know how easy/Hard it will be for you.

May 03, 2010 | 2000 Harley Davidson FLTR-FLTRI Road Glide

1 Answer

Do I need to remove my fairing to replace the headling bulbs?


Hi there,

well you can please follow the below steps -

Remove the Fairing - 1. Unscrew all seven outer fairing fasteners using a Torx driver. These screws are located on the inner fairing near the windshield, the speakers, and the handlebar clamps.
2. Stand in front of the motorcycle. Tilt the outer fairing toward you and hold it firmly. Reach in and disconnect the wire connectors for the headlight assembly by hand.
3. Move the fairing to a work bench to continue the procedure.

Change the Headlights - 1. Remove the wire harness connectors from the back of each headlight that need replacement. Turn the plastic retainer counterclockwise by hand to remove each bulb from its housing.
2. Install the new headlight bulb or bulbs, with each bulb's wider ears on the bulb back plates oriented toward the top. Screw in the plastic retainer rings by hand.
3. Connect the headlight wire harness connectors to the back of each headlight.
4. Move the fairing back to the motorcycle. Reinstall the fairing, battery and seat in reverse order.
Please post comments if you need more help or information.........

Good Luck!!

Thanks

Mar 17, 2010 | 2004 Harley Davidson FLTRI Road Glide

1 Answer

Replaced headlamp bulb and worked briefly. Checked fuses all seemed good and then headlight did not work. All gauges are now not functioning


Okay be very sure not to touch the "bulb" when replacing. Use latex gloves or a clean cloth, but never touch the bulb with your hands or anything that may have any kind of oil on it whatsoever.
Hope this helps.


JP

Nov 09, 2009 | 2008 Harley Davidson FLHX Street Glide

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75005 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...