Question about 2008 kawasaki Vulcan 1600 Nomad

Open Question

Headlamp on high beam blows fuse on 2008 Kawasaki nomad 1600

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
jakeslimco
  • 56 Answers

SOURCE: Headlight not working...bulb and fuse are good

check fuses first... if ok, buy an electrical tester from walmart for $5 and see if it's getting any electrical to the headlight.. if it is.. replace bulb

It's at least a good starting point.

Posted on Aug 30, 2009

Ad
  • 163 Answers

SOURCE: how do I take the rear tire off of a 2004 kawasaki nomad

I hope you have a jack... I had to remove the pipes and bags on my 04 vulcan nomad so I remove the cotter pin and pull the axle out of the rear hub. Then removed the spcer and rear brake. slide wheel assy. out of the drive hud on the left (removal of brake and spacer allow this) and drop the tire down. It's not hard...

Posted on Sep 22, 2009

Testimonial: "thanks for the help I am sure that I can do this now."

miket756
  • 2702 Answers

SOURCE: crank fuse on 2005 vulcan classic

keep pressing the starter and find out were the click is comeing from,, then change the starter solenoid, it sounds like this is at fault

Posted on Mar 02, 2010

Testimonial: "Thanks will go back out and try that...then I just have find the starter solenoid...I'm no mechanic but trying to learn to do some of this myself..."

  • 738 Answers

SOURCE: 2003 kawasaki 1500 fi nomad

Ok, locate and check the fuse at the starter solenoide, this is the main power fuse, follow the red battery lead until you locate the solenoide, here you should find under a cover a 30 amp fuse, hope this helps , paul

Posted on Feb 27, 2011

heimlich
  • 1978 Answers

SOURCE: I have a 2003 kawasaki

try cleaning your starter button. The starter button is a two position switch. First it turns off the headlight , then, it activates the starter solenoid. take apart the switch and try cleaning the contacts with alcohol. If the the button is broken you will have to replace the right switch assembly to fix a button issue. If the button checks out then open the headlight bucket and check the wire connections. A loose wire plug in or an internally broken wire could also be the culprit. Check the button first then go after the wiring.

Posted on May 06, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 Saturn aura wont start after trying to put rt.low lowbeam replacement


On the inside of the lid is a diagram .
The headlamps may be turned ON 2 different ways. First, when the driver places the headlamp switch in the HEADLAMP position, for normal operation. Second, with the headlamp switch placed in the AUTO position, for automatic lamp control (ALC). During ALC, the headlamps will be OFF in daylight conditions, or low beam operation in low light conditions. Battery positive voltage is supplied to the low beam relay and the high beam relay in the underhood fuse block. When low beam headlamps are requested, the body control module (BCM) supplies ground to the coil side of the low beam relay. This activates the relay and the relay supplies voltage to the left hand low beam headlamp through the LH LOW BEAM fuse and to the right hand low beam headlamp through the RH LOW BEAM fuse. Ground for the left hand low beam headlamp is provided at G101. Ground for the right hand low beam headlamp is provided at G102. When high beam headlamps are requested, the body control module (BCM) supplies ground to the coil side of the high beam relay. This activates the relay and the relay supplies voltage to the left hand high beam headlamp through the LH HIGH BEAM fuse and to the right hand high beam headlamp through the RH HIGH BEAM fuse. Ground for the left hand high beam headlamp is provided at G101. Ground for the right hand high beam headlamp is provided at G102.

Aug 14, 2017 | Saturn Cars & Trucks

1 Answer

2007 chev sub head lights wont turn on


Do you know anything about automotive electronics ? Electronic control modules .
Headlamp ON/OFF control is determined by the body control module (BCM) by a signal on the headlamp switch on input circuit when the headlamp switch is in the HEAD position. When the headlamp switch is in the AUTO position, the BCM determines headlamps ON/OFF by the voltage from the ambient light sensor.
If the headlight switch is left in the ON position, the inadvertent power control feature will turn OFF the headlights approximately 10 minutes after the ignition switch is turned to the OFF position. If the driver places the headlight switch in the ON position after the ignition switch has been turned OFF, or if the ignition switch is in the ACCY position, the headlights will remain ON until turned OFF or the battery runs dead.
The high beam indicator is illuminated when the instrument cluster receives a GMLAN serial data message from the BCM that the high beams are illuminated.
High Beams
The high beam headlamps receive voltage from the headlamp high relay located in the underhood fuse block. The BCM controls the relay on the headlamp high beam relay control circuit. High beam control is determined by a signal on the headlamp dimmer switch signal circuit from the multifunction switch. When the headlamp dimmer switch signal circuit is grounded, the BCM grounds the headlamp high beam relay control circuit, illuminating the high beam headlamps. The right and left high beam circuits are independent and are fused independently in the underhood fuse block.
Low Beams - Standard
The low beam headlamps receive voltage from the headlamp low beam relay located in the underhood fuse block. The BCM controls the relay on the headlamp low beam relay control circuit. Low beam control is determined by a signal on the headlamp dimmer switch signal circuit from the multifunction switch. When the headlamp dimmer switch signal circuit is open, the BCM grounds the headlamp low beam relay control circuit, illuminating the low beam headlamps. The right and left low beam circuits are independent are fused independently in the underhood fuse block.

Hooking up a factory scan tool an checking DTC'S - diagnostic trouble codes would be the very first step in trouble shooting this problem .
DTC B257A 00: Headlamp Switch Input Signal Mismatch
DTC 2575 00: Headlamp Control Circuit

Jun 30, 2017 | Cars & Trucks

1 Answer

2008 Kawasaki Vulcan nomad 1600 wont start. Engine keeps turning over and over but will not start and run on its own. 11,000 miles.


Hi, Gari and the usual suspects are:
1. Fuel tank empty.
2. The fuel tank has old dead gas.
3. Fuel tank bottom contaminated with ethanol sludge, dirt, water, rust, etc.
4. Fuel supply valve/petcock turned off.
5. Fouled spark plugs.
6. Engine flooded as a result of overuse of the enrichner.
7. Vacuum hose to the fuel supply valve/petcock disconnected, broken, cracked, or pinched.
8. Fuel valve/petcock or filter clogged.
9. Fuel line to carburetor or throttle body pinched, kinked or blocked.
10. Carburetor float stuck.
11. Fuel injectors clogged.
12. A severely discharged or damaged battery, you need 12.5 volts or better and be able to pass a load test if necessary.
13. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
14. Loose or corroded wire connection at the coil or plug between ignition sensor and ECM module.
15. Spark plug cables in bad condition and shorting check for spark leakage in the dark, cable connections loose, or connected to the wrong cylinders.
16. Ignition timing incorrect due to a faulty ignition coil, ignition module or MAP, CMP, CKP, O2, TPS, ETP, IAC sensors.
17. Faulty neutral, clutch lever, or kickstand safety switch.
18. Faulty fuel pump or fuse or relay.
19. A stuck bent or burnt valve.
20. Tilt sensor needs a reset.
21. Security system not disarming alarm needs a reset.
22. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
05 Nomad 1600 FI won start
What to do When Your Motorcycle Won Start
Kawasaki VULCAN 1600 NOMAD Service Manual
OEM Parts for Kawasaki
http://mybikemanuals.com/kawasaki/kawasaki-vulcan-owners-manuals

Apr 29, 2017 | 2008 kawasaki Vulcan 1600 Nomad

1 Answer

How to remove a rear wheel from a Kawasaki Vulcan Nomad 1600


Hi, Randy for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Removing Rear Tire
How to remove the rear wheel of your shaft driven motorcycle
KAWASAKI VULCAN 1600 CLASSIC Service Manual
OEM Parts for Kawasaki
2005 Kawasaki Vulcan 1600 Classic Owner Manual

Apr 24, 2017 | 2005 kawasaki Vulcan 1600 Nomad

2 Answers

2008 ford ranger headlight relay bad? Lamps do not light up, checked BULBS..OK no left highbeam Left and right lamp fuses ok and hi/lo 30a fuse ok


Did you check the fuse circuit for voltage, use a testlite or something.
I posted part of headlamp wiring. You understand your dimmer switch is involved in the circuits.
2008-ford-ranger-headlight-relay-tigo4fxke2krqgp04tlk3h2i-1-0.jpg

Oct 22, 2016 | 2008 Ford Ranger

1 Answer

No low beam headlights, but high beams work.


Which do you have
Low Beams - High Intensity Discharge (HID) OR
Low Beams - Standard ?

The low beam headlamps receive voltage from the headlamp low beam relay located in the underhood fuse block. The BCM controls the relay on the headlamp low beam relay control circuit. Low beam control is determined by a signal on the headlamp dimmer switch signal circuit from the multifunction switch. When the headlamp dimmer switch signal circuit is open, the BCM grounds the headlamp low beam relay control circuit, illuminating the low beam headlamps. The right and left low beam circuits are independent are fused independently in the underhood fuse block. I suggest you take an have it diagnosed by an ASE certified repair shop that has a scan tool that can communicate with the BCM .
DTC B2575 00: Headlamp Control Circuit

Mar 15, 2016 | 2008 Chevrolet Avalanche

2 Answers

My headlight on my 2005 kawasaki vulcan 800 classic won't turn on I have checked the fuse box twice and the fuse was burned up both times. Would this be the junction box?


Pull the headlamp out then replace the fuse. If it doesn't blow the fuse you new a new headlamp. If fuse blows start inspecting the wiring, it might have gotten pinched or frayed somewhere and this is causing the fuse to blow.

Apr 03, 2015 | kawasaki Motorcycles

1 Answer

I need the fuse box diagram for a 2008 ford focus.


Click on this link to have a look at the fuse diagrams here: http://www.fordservicecontent.com/Ford_Content/catalog/owner_guides/08focog3e.pdf
Visit support.ford.com at any time to get owner's manuals on most Ford vehicles...
Fuse #7, a 10A fuse, is for the left low beam headlamp.
Fuse #8, a 10A fuse, is for the right low beam headlamp.
Fuse #23, a 15A fuse, is for the high beam headlamp.

Sep 21, 2014 | 2008 Ford Focus

Not finding what you are looking for?
2008 kawasaki Vulcan 1600 Nomad Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...