Question about 2003 Kymco Hipster 125

Open Question

Kymco CK 125 getting at the battery?

Cant work our how to get at the battery - under the seat - can any one help?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: battery removal

hi,

Remove the plastic panel on the left side of the bike just under the seat and you will see the battery. unscrew the metal bar that holds it in and simply slide the battery out.

Posted on Mar 06, 2009

Ad
  • 72 Answers

SOURCE: timing headcam

get a manual for it and then you will be able to do any thing you have to do , when the time comes.

Posted on Mar 27, 2009

  • 5 Answers

SOURCE: No power on my Kymco Zing 125

your best try is to contact your dealer, and get them to order you the short red wire that runs from the + terminal on the battery, to the starter soleniod ( also has a thin red wire that runs to fuse holder) i had exactly the same problem and this solved it. i have however re done all the electrical connections on my bike using 7amp wire and bullet connectors, as i have had many faults with the electrics before.
My bike is a Kymco Cruiser 125 (almost exactly the same bike, i use kymco zing parts when replacing) i paid approx £16 GBP for the wire.

Posted on Oct 05, 2009

  • 1 Answer

SOURCE: tappet`s knocking on my kymco ck 125

Option 1: Go to mechanic

Option 2: Adjust the tappets. If you have never adjusted tappets or worked with engines before it is better to have someone experienced with you. The following is the procedure I use.

1: Carefully remove side panels.
2: Close fuel tap and disconnect pipe.
3: Carefully remove fuel tank. (undo the bolt under the seat and slide the tank 2 inches back, then lift it upwards)
4: Undo the bolts of the cylinder head cover (3 bolts with 12mm head, one of them also holds a small bracket for the throttle cable or ignition wire, I can't remember).
5: Remove the cylinder head cover. If you find this difficult put the bike in 5th gear and rotate the engine (by rotating the rear wheel) to the "inlet valve open" position so that the cover clears the "inlet valve rocker". Be careful that you do not damage the top cover gasket (made of rubber) or you will have an oil leak and no lubrication to the rockers.
6: Rotate the engine to a position with both valves closed, as close as possible to "top dead centre of compression/power strokes". There is a notch on the flywheel indicating top dead centre - you see this by opening the cap on the top of the flywheel cover on the left side of the bike. (do not stay at "top dead centre of exhaust/intake strokes")
7: Check the free play of the rockers on the valves. The service manual recommends a clearance between the valve and the rocker of 0.08mm with the engine cold (left to cool overnight). Maximum acceptable is 0.10mm and minimum is 0.06mm. The gap is checked using a feeler gauge (you know that you have a gap of 0.08mm by sliding a feeler that is 0.08mm thick and there is just a little friction slowing you down - if the feeler is hard to pull the gap is less than 0.08 and if the feeler passes with nothing resisting it then the gap is larger than 0.08mm).
8: If the tappets are knocking then the gap is too large. Undo the locknut on the tappet adjuster (10mm nut at the end of the rocker) just enough to let you turn the tappet adjuster. Then rotate the tappet adjuster until you get the right gap and tighten the locknut. Be sure to hold the tappet adjuster with pliers or something else while tightening the locknut so that the adjuster does not rotate.
9: Check and re-check that the gap between the adjuster and the valve is as specified. Incorrectly adjusted tappets are very bad for the engine, especially "tight" tappets with no gap between adjuster screw and valve. The first time you adjust tappets you might have to repeat from step 7 several times until you get used to it.
10: Assemble everything in the reverse order of disassembly. You might have to rotate the engine to "intake valve open" position again to place the cylinder head cover easily. During assembly be careful the the rubber gasket of the cover is not damaged or out of place. There is an oil path from the head to a nozzle above the rockers and the gasket must seal this well.
10: Once you assemble everything start the engine and once it is hot enjoy a more silent bike. It is normal on these engines to have some tappet noise when cold, but if the tappets are adjusted right they are nearly silent when hot.

Always refer to an expert when you are not sure. Maybe the first time it is safer to watch your trusted mechanic do this work.

Posted on Sep 23, 2010

fixya167
  • 119 Answers

SOURCE: deristrict kymco Stryker 125

there are different methods of restricting, hear we 1. gasket between the carb and inlet. ". gasket between the exhaust and head, 3. washer in the output sprocket to drive to wheal in the centrifugal clutch Re: Jeff

Posted on Apr 12, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kymco 125 Pulsar CK service manual


Hi, Diane the vast majority of service, parts, and owners manuals on the internet are "FREE" to download and all service manuals contain wiring diagrams in the back pages. The rest usually charge a modest fee around $10 and there is a handful of obscure, rare, obsolete, and very old models that are no longer or never were available, for these rare occasions I shall look on eBay and find the cheapest one available. Most of the manuals will cover your exact make, model, and year otherwise one will be provided that comes as close as possible to your bike and will have most of the same info that an exact manual would have. Diane, I left multiple choices some have long shipping dates read the fine print. To download your manual please click on the blue links below. Good luck and have a wonderful day
Haynes Motorcycle Manual 4871 Chinese Taiwanese Korean 125cc
CK 125
Haynes Manual No 4871 Motorbike Motorcycle for Kymco Pulsar 125 99 06 eBay
poscompanies com
Kymco 125 Pulsar CK 2005

May 19, 2017 | Kymco 125 Pulsar CK Motorcycles

1 Answer

How do you remove the seat from a 2012 pulsar 125


Hi, Anonymous in the future please state the manufacturer of your bike Bajaj or Kymco it would really help for more information about your question and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
how to take off and open the seat of kymco pipe
KYMCO 125 PULSAR Manuals
https://www.youtube.com/watch?v=L0d12f3jzYU
Bajaj Pulsar 150 Maintenance Manual

Jul 24, 2016 | Motorcycles

1 Answer

Kymco ck 125 have no spark


is engine earthed to battery ok, check ht caps and leads, is power getting to coils when bike being turned over

Feb 22, 2013 | Motorcycles

3 Answers

My Kymco ck125 wont start on electric start?? It has new battery and spark plug???what next?


Hi,
Check the power going to the starter and the relay connection.
Usually the relay is at fault, oxidation have accumulated in the terminals and you have to clean it out.
Check also the STARTER switch.

Hope that helps!

Nov 08, 2011 | 2005 Kymco 125 Pulsar CK

1 Answer

Cant find the battery


Normally under the seat or under right cover

Mar 22, 2010 | 2003 Kymco Hipster 125

2 Answers

Battery keeps loosing charge- kymco cruiser 125, 2005


I had this exact same problem on a hipster 125, it was a faulty regulator module ( mounted under the seat) I also found a short circuit (somewhere) in the wiring loom between the regulator output and the chassis (probably what killed the regulator in the first place!) I cut and replaced the entire wire to save removing most of the loom and after testing reg to ensure it was dead i fitted a new one (about £60) bike charges and runs like a dream now even with fully lights approx 80% of the time. good luck

Jul 14, 2009 | 2005 Kymco Hipster 125

1 Answer

Timing headcam


get a manual for it and then you will be able to do any thing you have to do , when the time comes.

Mar 27, 2009 | 2001 Kymco Stryker 125

3 Answers

Oil bolt has rounded of what size is the bolt??


fit in a helical, and keep in the same bolt, that should solve your problem

Feb 18, 2009 | 2005 Kymco Stryker 125

1 Answer

Battery removal


hi,

Remove the plastic panel on the left side of the bike just under the seat and you will see the battery. unscrew the metal bar that holds it in and simply slide the battery out.

Dec 11, 2008 | 2003 Kymco Hipster 125

Not finding what you are looking for?
2003 Kymco Hipster 125 Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kymco Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Kymco Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...