Question about Suzuki Motorcycles

1 Answer

Suzuki maurauder 800 clutch slip - Suzuki Motorcycles

Posted by on

Ad

1 Answer

Repost under motorcycles

Posted on Jul 25, 2013

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 456 Answers

SOURCE: I have a 1999 suzuki

hi.
as long as there is a little play on the clutch lever (1-2mm) then the clutch will probably need replacing. the cable can usually be adjusted at the lever end, and at the gearbox end, but given the age of the bike it is quite likely that the clutch need replacing. check for play on the cable first, but be prepared for a new clutch.
please feel free to ask again if you need fitting instructions.

Posted on Jul 15, 2011

  • 265 Answers

SOURCE: 94 suzuki 800 intruder. clutch splips in

No adjusting is possible.
Slip can be caused by several defaults:
- Wrong engine oil ( SAE 10w-40 API SE or SF only )
- Weak clutch springs ( free spring length : 34mm ( 1.34in ) MINIMUM
- Worn clutch disk 2(internal teeths ) ( wear limit 3.15mm ( 0.124in ) ) This is the last disk, against the clutch center
- Worn clutch disks 1 (internal teeths) ( wear limit 2.62mm ( 0.103in ) )
- Clutch plates ( thikcness between 1.55 and 1.65mm / 0.0610 and 0.0649 inches
- Damaged pressure plate ( cracks round the spring holes )

To check the clutch parts, the right engine cover must be removed.
Take attention while loosening the clutch spring bolts!
Drain engine oil, and set engine into first gear ( this locks the clutch for an easy loosening of the spring bolts )

Hope it helps

Posted on Apr 02, 2009

czaa
  • 4521 Answers

SOURCE: how to adjust clutch on 1979 motorcycle Suzuki A50 - 11

u start at handlebar lever 1st-loosen the cable nut and see if it helps-if not then go where it connects to engine-probly need a haynes manual for details

Posted on Aug 28, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need color coded wiring schematic for2002 vz 800 maurauder,I have no keyswitch and need to know how to wire in another one


Hi, Troy sorry you can't find the first and best tool you ever bought for your Suzuki despair not for a mere $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
2002 suzuki marauder vz800 wiring diagram Google Search
http://www.mediafire.com/download/32ejwmnnw4m/VZ800_Service_97_02.pdf
OEM parts for Suzuki
Suzuki VZ800 Marauder

Jul 18, 2015 | Motorcycles

1 Answer

My clutch seems to slip in higher gears on my suzuki intruder but takes off from dead starts just fine. what does it sound like the problem is?


Sounds like you either need to adjust the clutch cable - there should be a little bit of play in it before it disengages the clutch - or you need a new clutch kit (plates, springs, etc). What mileage is on the bike and has the clutch ever been changed?

Jul 13, 2014 | 1992 Suzuki VS 800 Intruder

1 Answer

Where is the slave cylinder on a 2005 suzuki forenza


M/T car with a clutch
the slave is the device that pushes the clutch lever , as it enters the clutch bell housing (the hunk of alum. that is between the engine and trans 'bell shaped..)
400 or 4000? , my guess is you mean, 4000 rpm
3000 on the round is normal./
the engine should idle at 800 rpm.
that is just 1 tick below the 1 (1 = 1000 on the scale see the 1k or
x1000 on the dial, that means all numbers are times 1000.
so point 8 rpm is 0.8 x 1000 or 800.

do not ride the clutch pedal or you will buy many a clutch.
the save bad, never cause, slipping clutch. (near impossible)
the hyd, clutch actuator is self adjusting as clutch wears.
the clutch will grind gears if the slave fails. the slave annoucces its bad in advance buy loss of fluid on ground and level drop on the cutch master cylinder.
post the symptoms, and ask for help based on those facts.
a slipping clutch is a bad clutch. (or soaked in oil, and same )
please repost real RPMs using the x1000 scale factor for best answer
and when they happen.

Feb 12, 2013 | 2005 Suzuki Forenza Wagon

1 Answer

Clutch slipping


can you get it out of gear?
can you change gear
does the clutch drag ( shifts are difficult )
the clutch plates are froze/ stuck together, remove clutch, check plates for rust clean soak in fresh oil replace any that are rusty..

Feb 24, 2012 | 1998 Suzuki VS 800 Intruder

1 Answer

I have a 1999 suzuki marauder 800. Ive noticed that under load or heavy throtle that the clutch starts slipping. is there an adjustment i can make or do the clutches just need replaced all together. thanks...


hi.
as long as there is a little play on the clutch lever (1-2mm) then the clutch will probably need replacing. the cable can usually be adjusted at the lever end, and at the gearbox end, but given the age of the bike it is quite likely that the clutch need replacing. check for play on the cable first, but be prepared for a new clutch.
please feel free to ask again if you need fitting instructions.

Jul 15, 2011 | 1999 Suzuki VZ 800 Marauder

1 Answer

Can't get the clutch on a suzuki 800 intruder to hold pressure


Oil should be 10W40 SF or SG grade. Anything else will cause the clutch to slip. There must be freeplay on the clutch cable (0.4-0.6in). Adjust handle bar clutch lever screw all the way out then adjust at gearbox end and revert to handle bar adjustment for fine adjustments. If this does not solve the problem take the clutch apart and measure driven plate thickness (3.12in minimum for the 1st plate and 2.62in minimum for the others)
Measure clutch spring free length. There are 2 sets (4 springs each). 0.97in minimum and 0.92in minimum respectively.
A slipping clutch is caused by incorrect friction, that is incorrect oil or insufficient pressure. Pressure is supplied by the springs on the discs and driven plates.
If the discs, driven plates or bucket is worn it will cause slippage.
If you pull in the clutch and it disengages but starts to re- engage after a short period you will need to replace the clutch master cylinder seals.

Sep 22, 2010 | 1994 Suzuki VS 800 Intruder

1 Answer

Transmission slipping


blame it on the clutch, you may have a worn our disc or a loose clutch spring or both. easy replacement will do the trick if you do DIY

Apr 13, 2010 | 1995 Suzuki VS 800 Intruder

1 Answer

All gears from 1 to 5 are slipping. each gear


does the clutch lever release "sharply" and snap back after engagement? then lean bike over drain about a quart of oil, take off access cover to clutch and check to see if you have any broken clutch springs. if thats looks o.k. you"ll probably need new clutch plates. a real quick check when you ride the bike smell the oil, does it smell burnt? if it does, the plates are probably no good.

Apr 02, 2010 | 1996 Suzuki VS 800 Intruder

1 Answer

How do u adjust the clutch on my suzuki vl800 its starting to slip its a cable clutch


There should be a finger adjustment screw, where the clutch cable meets the clutch lever. turn it outwards one turn at a time ,if more than five turns or reach end of thread ,your clutch will need replacing.

Feb 14, 2010 | 2001 Suzuki VZ 800 Marauder

1 Answer

1993 Suzuki Intruder 800


Sounds like clutch slipping.. you may have to replace the clutch plates.

Jun 17, 2009 | 1993 Suzuki VS 800 Intruder

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

Richard
Richard

Level 2 Expert

83 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...