Question about Yamaha Motorcycles

1 Answer

Brake line how to bleed out break line

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 1 Answer

Fill the resevor with fluid pump brake and hold down and break open bleeder on caliper continue to hold brake lever and retighten bleeder valve and pump again till no bubbles come out of bleeder

Posted on Jul 21, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Horrible break pedal.


Is there any grinding? You may need new front brake pads. I might also have the brakes bleed for there may be air in brake line. Thank you and Please leave feedback

Jul 11, 2016 | 2006 Mazda 3

1 Answer

Cant get breaks on my 2002 blazer ather break lane breaks


After you fix a brake line, you need to bleed the line. There is air in the line that needs to be bleed out of the line. Make sure the vehicle is not running, totally shut off. First - find which tire the brake line goes to that you just fixed. Two - then have someone in the vehicle pumping the brake three times, then on the third time, have them hold the brake to floor. Three - open the bleeder valve on the brake caliper of the tire that the brake line goes to.(Note - You need the tire off the vehicle to do this.) Four - once the the bleeder valve is opened, and all the brake fluid, and air comes out, close the bleeder valve and repeat the whole process several more time. Each time you bleed the brake line you are releasing the air in the line, and creating pressure with just fluid in the line. Usually three to four tries of bleeding the line will solve the air in the brake line problem and your brake pedal will become hard.

Mar 22, 2014 | 2002 Chevrolet Blazer

1 Answer

Brake and e brake warning lights stay on happen when i blew a brake line.


If brakes are mushy then you still have air in the lines.Did you bleed all 4 wheels?have wife push brake pedal down once and hold then bleed hold down one and bleed and so on if this has a quick takeup master cylinder pumping 3 or 4 times then bleed wont work

Jun 14, 2012 | Chevrolet Cars & Trucks

2 Answers

Just changed rotors and front brake pads. Pumped pressure back with break pedal. After you start vehicle all break pressure is lost- no breaks. Whats going on?


You are either low on brake fluid or you have a vacum problem. It is a long shot but possible the Master Cylinder is having an issue or an air bubble in the system. Start the vehicle and make sure it is blocked. With the engine running perform system bleeds on all four calipers. Pump 3 times then release bleed valve. You are going to need a couple bottles of brake fluid to bleed all these calipers and get the air out of the lines. You should make sure the primary vacum is connected to the master cylinder and that there are no leaks on any lines before you start the bleeding process.

Jun 24, 2010 | 1999 Toyota 4Runner

1 Answer

I have bleed rear breaks.I cant seem to get fluid to rear.The ABS light is on along with the break light.Is it possible that there is a faulty ABS sensor not allowing fluid to be distributed to the rear...


I'm confused, how did U bleed the rear brakes and there's no fluid to them? first of all U need to get fluid to the rear.

  1. Make sure there fluid in the brake reserve
  2. leave the cap off the reserve
  3. crack open the furthest bleeder valve till fluid come out (take it off if U have 2)
  4. if nothing still come out, then U have a clogged brake line
  5. blow back through the line from the brake side (slow till it bubbles back through the reserve
  6. then gravity bleed it, tighten up the the valve
  7. now U can bleed the brakes

May 04, 2009 | Pontiac Grand Am Cars & Trucks

2 Answers

What causes there to be no fluid to either side of the rear breaks


several thing came cause this. \
1). rear section of the masker brake cylinder has air.
2). break or leak in the brake line
3). brake cylinder (piston) boot leaked.

have some one help you to bleed the brake.
let me konw if you need instruction on bleeding the brakes.

May 04, 2009 | 1998 Pontiac Grand Am

1 Answer

Trouble Bleeding Break Line


you need to hold in the metering valve.when you bleed the front brakes.long as the valve closed off you wont be able to bleed front brakes.better to get extra help.hard to bleed by your self .

Apr 20, 2009 | 1988 Oldsmobile Delta 88

1 Answer

96 nis max rear break dont work


Sounds like you have a blockage in the brake line going to the back breaks...maybe a kink in the brake line or maybe the junction piece (found attached to the bell housing in the back) that sends brake fluid to both breaks in the back is bad. Or your rear breaks need to be adjusted... I would say brake cylinders, but I doubt both would go out at the same time. Also check to make sure your master cylinder is working ok and there is no air in the line...try bleeding the back brakes to see if any fluid is getting to the brake cylinders in the back, this will tell you if you have a kink in the line or air...if it bubbles when you check (bleed the lines) then your problem is air in the line and should be bled until you get a solid flow of break fluid with no bubbles at all. If you want to know how to bleed the rear break just write me back and I will instruct you on how to do that.

Apr 19, 2009 | 1996 Nissan Maxima

2 Answers

Changed break line but still have no pressure in breaks


to do a complete job. you need to bleed all 4 wheels, starting from Right Rear. Right front. Left Rear. Left Front.

Apr 07, 2009 | 1995 Chevrolet Silverado 2500

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...