Question about Enfield Motorcycles

1 Answer

Loose throttle my accelerator has loose it is rotating completely what i have to do

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Enfield Master
  • 40,775 Answers

If you can twist the handle completely without any engine response the I imagine that the cable has broken probable in the handle piece. Check it out and replace if required.

Posted on Jul 21, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

COMPLETE LOSS OF ACCELERATION


this vehicle is built with a throttle body by wire, that means that it doesn't have the cable from the accelerator to the throttle body, normally this happens when people change the battery, try disconnecting the battery for 10 min, then touch the 2 terminal cables together, to discharge any power in the system, connect battery and try again. if it doesn't work, you well need to program the throttle body or a may be defective. also check all of the fuses, all of them not just some. good luck.

Apr 21, 2014 | 2004 Nissan Murano

Tip

How to reset ECU,Throttle and Accelerator Position Learning


Hi.

Below the procedure to reset ECU,Throttle and to perform Accelerator Position Learning on Nissan. It works on Titan, Altima, Infinity, pathfinder and other models.

ECU Resetting


While performing the procedures below, ensue that you are respecting the times stated. If the steps are not done within the specified times, the module will not reset. You will need to use a watch or a chronograph while performing the procedures.

Procedure:

1. Ensure that the accelerator pedal is fully released, set ignition switch to the “ON” position, then wait 3 seconds.
2. Follow the steps a and b below, repeat the two steps in sequence quickly for five times within 5 seconds.
a. Push hard the accelerator pedal untill fully depressed.
b. Release the accelerator pedal in full.
3. Wait 7 seconds, then depress the accelerator pedal completely, and hold it for about 10 seconds until the CEL (check engine light) starts blinking.
4. Release the accelerator pedal while the CEL is still blinking.
5. Wait 10 second.
6. Depressthe accelerator pedal in full and hold it for 10 seconds or more.
7. Fully release the accelerator pedal while the CEL light keeps flashing.
8. Turn the ignition switch to “OFF” position and start the vehicle. If procedure has been done correctly, then the light light will turn off.
If the light continues to stay on, repeat the procedure.

Accelerator Pedal Release Position Learning

Procedure

1. Ensure that the accelerator pedal is completely released before starting the procedure.
2. Turn the ignition switch “ON” and wait at least 2 seconds.
3. Turn the ignition switch “OFF”, and wait at least 10 seconds.
4. Turn the ignition switch “ON” and wait 2 seconds.
5. Turn the ignition switch “OFF” and wait 10 seconds.

Throttle Valve Closed Position Learning

Procedure

1. Ensure that accelerator pedal is completely released.
2. Turn ignition switch to the “ON” position.
3. Turn ignition switch to the “OFF” position and wait at least 10 seconds.
Ensure that the throttle valve moves after turning the switch off.

Idle Air Volume Learning (Throttle Position Learning)

Procedure

1. Follow the Accelerator Pedal Released Position Learning described above.
2. Do the Throttle Valve Closed Position Learning also described above.
3. Start the engine, and allow warming up.
4. Turn the ignition on “OFF” positionand wait 10 seconds.
5. Ensure that accelerator pedal is fully released, then turn the ignition switch to “ON” position, and wait 3 seconds.
6. Repeat the steps a and b below five times within 5 seconds in sequence.
a. Push hard the accelerator pedal untill fully depressed.
b. Release the accelerator pedal until reaching full extension.
8. Wait 7 seconds or more, depress the accelerator pedal completely and hold the pedal down for about 20 seconds until you see that the Check Engine Light stops blinking and starts getting steady..
9. Rrelease completely the accelerator pedal within 3 seconds after the light coming ON.
10. Start engine and let it run at idle for about 20 seconds.
12. Test the engine to ensure the idle speed and ignition timing are set correctly.

Regards.

on Mar 25, 2010 | Nissan Titan Cars & Trucks

1 Answer

Engine cuts out and does not accelerates


you will have both a throttle position sensor and a peddle position sensor both fitted to your throttle ,the cars ECU must pick up both sensors so it is not doing so you may need to change the throttle body.as you can not just change the sensors on there own.

Mar 27, 2014 | 1995 Mazda MPV

1 Answer

2009 Schenn scooter


cable retainer might be broken, / cable housing might also be damaged or simply the handle grip/ or throttle grip is only loose

Jun 03, 2013 | Motorcycles

1 Answer

I have a 2004 mercury mountineer the servce engin light has come on and the engin fail safe mode. i had a test done on it and it says throttle actultor dontrol system could you please tell me what that...


Hi, your truck must use a stepper motor to control the throttle. The computer is getting a signal from the accelerator position sensor and trying to rotate the throttle, but it is having trouble either rotating the throttle or sensing the position of the throttle. If you can give me the exact trouble code, I may be able to say more about what the problem is.

Aug 07, 2011 | 2004 Mercury Mountaineer

1 Answer

2006 jag x-type when i comeing to a stop but i don't stop completely stop than i press the throttle the car jerks what causes that and can it be fixed


VECHICLE SURGE ON ACCELERATION POSSIBLE CAUSE COULD BE FAULTY ACCELERATOR POSITION SENSOR,FAULTY FUEL PUMP,CLOGGED FUEL FILTER + DIRTY FUEL INJECTORS.AIRFLOW DUCT TO THROTTLE BODY LOOSE OR DISCONNECTED.

Nov 03, 2010 | Jaguar X-Type Cars & Trucks

1 Answer

Where is the throttle located on a 1992 dodge spirit? The car wouldn't stop accelerating until mashing the break to stop the car. Now the driver is on the side of the road with the hood popped looking for...


It's hooked to the throttle cable. It's roundish plastic disc & can be rotated by hand. Sometimes the cable frays & sticks the throttle open. It could also be caused by a sticking floor mat that has jamed up underneath the accelerator pedal. Try tying the mat to the seat frame to stop it from jamming up.You may have to change the throttle cable however. Hope this helps. Good luck!

Aug 30, 2010 | 1992 Dodge Spirit

1 Answer

Pepboys gave me the obd code p2004 imrc bank 1 stuck open? what does this mean and how much is it likely to cost to fix?


P2004 INTAKE AIR SYSTEM MALFUNCTION. POSSIBLE CAUSE.TEST FOR STICKING ACCELERATOR OR SPEED CONTROL CABLE TURN OFF KEY AND DISCONNECT ACCELERATOR AND SPEED CONTROL CABLE FROM THROTTLE BODY.ROTATE THE THROTTLE BODY LINKAGE TO DETERMINE.IF IT ROTATE FREELY.THE THROTTLE BODY MAY HAVE FAILED.CHECK AIR CLEANER AND AIR INLET ASSEMBLY FOR RESTRICTIONS.CHECK THE IAC MOTOR RESPONSE.IT MAY BE DAMAGED OR STICKING.CHECK PVC SYSTEM VALVE AND HOSES FOR LEAKS AND PLUGGING.CHECK FOR SIGNS OF VACUUM LEAKS IN THE ENGINE OR COMPONENTS. TEST TP SENSOR SIGNAL DUE A SWEEP TEST AT KEY ON ENGINE OFF

Mar 29, 2010 | 2000 Ford Focus

1 Answer

No revs when depressing the accelerator


check the gas cable at the throttle body under the hood, it is possible the cable has either broken or become dis connected. remove the air cleaner and look into throttle body and find the rotating shaft that opens and closes the plate inside throttle body. 1) when you rotate does plate move? 2) is there cable attached to pulley? 3) when someone steps on pedal does the plate move? 1 not likely issue, 2 might be issue reattach cable to pulley, 3 pedal does not move pulley cable disconnected at pedal reconnect there or cable is broken replace cable. if non of these then throttle position sensor may be bad and check or replace

Oct 30, 2009 | 2005 Volkswagen Golf

1 Answer

For Focus Check Engine Light P2004


CODE P2004 INTAKE AIR SYSTEM MALFUNCTION. POSSIBLE CAUSE.TEST FOR STICKING ACCELERATOR OR SPEED CONTROL CABLE TURN OFF KEY AND DISCONNECT ACCELERATOR AND SPEED CONTROL CABLE FROM THROTTLE BODY.ROTATE THE THROTTLE BODY LINKAGE TO DETERMINE.IF IT ROTATE FREELY.THE THROTTLE BODY MAY HAVE FAILED.CHECK AIR CLEANER AND AIR INLET ASSEMBLY FOR RESTRICTIONS.CHECK THE IAC MOTOR RESPONSE.IT MAY BE DAMAGED OR STICKING.CHECK PVC SYSTEM VALVE AND HOSES FOR LEAKS AND PLUGGING.CHECK FOR SIGNS OF VACUUM LEAKS IN THE ENGINE OR COMPONENTS. TEST TP SENSOR SIGNAL DUE A SWEEP TEST AT KEY ON ENGINE OFF.

Sep 19, 2009 | 2000 Ford Focus

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Enfield Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

kevin bulsara

Level 2 Expert

234 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Enfield Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...