Question about 2006 kawasaki ZX-6R

1 Answer

Turns over but wont start

Had to have key in a certain position to start if not it would just turn over. now i cant find the position. is there a way around this .

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 134 Answers

Did u check the wires from the ignition?..if the wires are ok then i think u must change the ignition contact if you need more help i had found a good service manual for zx-6r from 2006 it will help you with the electrical system and other stuff check the below link:
http://goo.gl/wm4xO
Thanks

Posted on Jul 21, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Honda Jazz 200, the key does not want to turn when we want to start the car


If the key wont turn at all, try pulling the steering wheel (hard) to either side while turning the key. Sometimes if the steering wheel locks in a certain position it will "lock" the ignition cylinder in place, and pulling away from the ignition will take the pressure off and allow it to move. IF this doesn't work, you may have a bad "ignition lock cylinder"

Apr 15, 2017 | Honda Cars & Trucks

1 Answer

Key stuck ignition wont


This usually happens if your steering wheel is in the rightmost or the leftmost position. Try wiggling the steering wheel when pulling out the key.

Jul 20, 2014 | 2000 Pontiac Grand Prix

1 Answer

2006 volkswagon passat key stuck in the ingination cant shift gears


Can you turn the key forward and back to the off position, Is the shift lever in the park position, Is the steering wheel in the locked position????

Jan 03, 2014 | Cars & Trucks

1 Answer

Turn on ignition jeep starts ok sometimes spedo and idicators wont work unless you move key adain while running


There could be some play in the ign switch allowing the voltage to be lost in certain position. Turn key to run position, do start engine. Turn on blower fan, turn signal, radio . Wiggle the key to see if they go off with key movement. If so replace electrical switch behind the key and tumbler

Nov 02, 2013 | Cars & Trucks

1 Answer

How to turn off theft the van cant start


cant turn off problem you can try another key.put key in the ignition turn on position for 3 seconds the security light should turn off.then turn off ignition switch wait 5 to 10 seconds try start vechicle if still fails to start.problem in the theft security system.dealership has to code scan problem could be in the ignition switch which is antenna ring.problem could be transponder key or problem could be in the immobilizer control module and ECM.

Feb 11, 2013 | 2000 Ford Windstar

1 Answer

Battery fully charged, car wont start, cant remove key, 2004 cadillac cts


There is a magnetic switch on the 'park' position. The car only starts or releases the key in 'park' is enabled. Maybe this switch is not working! Try to replace it!

Apr 11, 2012 | 2007 Cadillac CTS 3.6L

1 Answer

1997 sunfire key stays in run position wont turn off


you mean you cant take your key out .

Nov 13, 2011 | Cars & Trucks

1 Answer

Car wont start, replaced battery and positive battery cable


Make certain the car is in park. If it is, try turning key to on position and hold brake and shift to neutral to try to start it.

Aug 07, 2010 | 1998 Mercury Grand Marquis

1 Answer

Wont start is a voltage regulator on the isuzu axiom that would keep from starting


No. Check of faulted PCM. With car off, turn key to ignition ON, and do not crank. Look for check engine light to flash. If it does not, PCM is faulty. Also, possible crank position sensor or cam position sensor failed. The PCM needs to verify a certain number of RPM before the fuel pump will turn on.

Mar 30, 2010 | 2003 Isuzu Axiom

1 Answer

Chevrolet mailbu 2001 help.


check the crank position sensor

Jul 15, 2009 | 2001 Chevrolet Malibu

Not finding what you are looking for?
2006 kawasaki ZX-6R Logo

145 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...