Question about 2011 Bajaj Pulsar 150

1 Answer

Speed sensor sensor reset

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Bajaj Master
  • 43,050 Answers

Hi Vishnu the vast majority of speedometer issues is caused by the speed sensor and or the wiring. On Sportsters the sensor is located on top of the engine case behind the rear cylinder, on big twins it's located on the right side of the transmission case between the starter end cap and the transmission top cover. Remove the bolt/screw that secures the sensor and lift the sensor out of the case. Inspect it for damage and contamination, if there appears to be no damage wipe the end of the sensor clean and reinstall, you can go for a short quick test ride to see if the speedo is working. If the issue still exists grab your test light and unplug the harness connector from the sensor, check for power (red wire) and ground (black wire) continuity coming from the speedo, there is also the connector that plugs into the speedometer, also look for corroded, broken or loose pin/sockets. If everything checks out OK then replace the speed sensor. For more information about your issue, please visit the websites below. Good luck and have a nice day. http://88.198.249.35/d/Pulsar-150-Workshop-Manual.pdf

Posted on Nov 18, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I just repaced the right front speed sensor in my 2009 jeep patriot limited and the lights are still on.how long til it resets or how do i reset it?


speed sensor (which one) my guess the story goes.
CEL came on
went to autozoned, they scan it and get , undisclosed DTC error
you then see the word speed, and starter replacing any of 4 speed sensors on car.
the scan tool has a reset button, use that first.
if the problem is still there, it will NEVER CLEAR, (by Design)
why not post the DTC errors we can all wax smarter, x10
no engine option stated,
no transmission option either.

the engine can have 2 speed sensors, CKP and CMP, crank and cam.
the trans up to 3 speed sensors.
gue$$ing is expen$ive.
no?

Mar 11, 2015 | 2009 Jeep Patriot Limited

1 Answer

Reset speedodometer after replacing speed sensor 2000 mitsubishi eclipse


you may have to reset the cpu program with a scanner to cater for the new sensor.

Dec 27, 2014 | 2000 Mitsubishi Eclipse

1 Answer

Keeps Resetting In Middle of Workout


You might try adjusting the speed sensor. It may simply just be that they are not heavy enough to make it turn fast enough to work. The following information should help you to make the adjustment I mentioned. Speed Sensor Testing and Adjustment for Stairmaster 4400cl and 4600cl Steppers Testing and Adjustment of Stairmaster 4600CL and 4400CL Speed Sensor Tools Needed: Volt Meter, 7/16" Wrench
A common misconception about battery powered units, it that it only requires you to step on the pedals to power the console; when in fact the speed sensor plays a major role in powering the console.
If you step on the pedals and they fall to the floor due to the console not powering up so there is no resistance, you should check the speed sensor.
The speed sensor is mounted to the alternator and reads the speed sensor disc when the unit is pedaled producing an AC voltage. The voltage from the speed sensor can be tested at the connection of the speed sensor to the lower control board. The connection is a red and black wire. Using AC setting on your volt meter at its lowest range, place the red lead to the red wire and the black lead to the black wire. Make sure the leads of the volt meter are making a good connection. Now step on the unit and verify the voltage from the speed sensor. A good speed sensor will produce about 3 VAC before the console powers up.
If the voltage is not correct, inspect the adjustment of the speed sensor. It may be necessary to adjust the sensor closer to the speed sensor disc. Proper gap of the speed sensor to the disc is about the thickness of a business card.
Retest unit after making speed sensor adjustment.

Feb 01, 2014 | Stairmaster 4600 Cl Cordless Freeclimber

1 Answer

Ml 320 speed sensor can it be changed by me or does the computer have to be reset


Speed Sensor is an output sensor

If you can get to it-- you can change it, but why

No codes tell you a part failed or needs to be replaced

The (ECU) should not need to be reset, as you call it

Sep 21, 2013 | Mercedes-Benz ML320 Cars & Trucks

1 Answer

Freelander abs


Sounds like the RF speed sensor is bad, normally you can set a multimeter to ohms and put it on the disconnected wheel sensor and see if you get a reading off the sensor. If you do, then the sensor is ok, and may be the ring on the drive shaft.
I would swap the sensor out and reset the codes.

Jun 17, 2013 | Cars & Trucks

2 Answers

The car is in limp mode and the code its throught at me is p1643


P0163 O2 Sensor Circuit Low Voltage (Bank 2 Sensor 3) most likely a faulty sensor

Apr 17, 2011 | 2003 Jaguar X-Type

1 Answer

Engine light po501 and replace sensor and still won't go off


A P0501 DTC trouble code may be caused by one or more of the following:
  • The Vehicle Speed Sensor (VSS) is not reading (functioning) properly
  • There is a broken/frayed wire leading to the vehicle speed sensor
  • The vehicle's PCM is not correctly configured for the actual tire size on the vehicle
Possible Solutions The simplest thing to do is to reset the code and see if it comes back.
Next, check all wiring and connectors that lead to the speed sensor. The location of the sensor depends on your vehicle. The sensor could be on the rear axle, transmission, or perhaps the wheel hub (brake) assembly.
If the wiring and connectors are OK, then check the voltage at the speed sensor. Again, the exact procedure wil depend on your make and model of vehicle.
If everything looks OK, replace the sensor.

Also, confirm to reset the PCM stored codes.

Hope helps (remember to rate this).

Oct 14, 2010 | 2004 Jeep Grand Cherokee

1 Answer

My 2001 Honda Odyssey D4 light is flashing, CEL and TCS lights are on. The code is P0715 which means Turbine speed sensor circuit failure. Is this a tranny failure or just a speed sensor problem?


the code 0715 is Mainshaft speed sensor, check the sensor see any loose connection or replace the sensor . After replace the sensor, reset the the system. Hope this can help.

May 30, 2010 | 2001 Honda Odyssey

1 Answer

E300 1994 codes read p0720 and p0500 one is speed sensor and the other is tran speed sensor, we are having prob with tran shifting and various speeds and rpm jumping up then shifting.


try changing the drive shaft speed sensor, sounds like you have a malfunctioning drive shaft speed sensor, change sensor and reset codes and test... e 300 had this problem in 94 and 95 even when they were close to new with very low miles... please rate my help , thanks

Aug 05, 2009 | 1994 Lexus Es 300

2 Answers

2000 FLHRI turns over but won't start


Hi,
I found this info for you.  Have you tried the built in diagnostic in your speedometer? You can access them by: 

1) While you ignition is off hold the reset button 
2) Turn the key to the on position. 

Now from each reset button push the speedometer will test the following: 

d01 Speed sensor power output shorted low 
d02 Speed sensor power output shorted high or open 
d03 Not Used 
d04 Not Used 
d05 Speed sensor return shorted high 
d06 Speed sensor return shorted low 
d07 Not Used 
d08 Speedometer power over voltage 
d09 Speed output shorted high 
d10 Speed output shorted low or open 

The last number CAL14 is the calibration number. 
To reset all codes while in diagnostic mode, hold the reset button in for 5 seconds. 

Each test will read dXXSEt if there is a problem, or dXXCLr if there is not. (XX being the number of the list above) The 

From what I can tell it will test if your speed sensor, speedometer, or wiring is the problem. 

Hope it helps. Cheers
regards robotek

Jan 05, 2009 | 2006 Harley Davidson FLHR Road king

Not finding what you are looking for?
2011 Bajaj Pulsar 150 Logo

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bajaj Experts

sachin sharma
sachin sharma

Level 2 Expert

171 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

Are you a Bajaj Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...