Question about kawasaki Motorcycles

1 Answer

Kawasaki setting points

Kawasaki Z650 B3 model points and plugs setting

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert who has written 20 answers of more than 400 characters.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 134 Answers

Hello, i will give some useful info for the plugs, settings are from Z650 B1 but it will work on B3 too
Gap 0.7~0.8
Tightening: 2.5~3.0 kg-m
Torque 18.5~22.0 ft-lbs
You can find more information in the below service manual link for z650
Get it from the below link:
Good Luck

Posted on Aug 07, 2013


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: I have a Kawasaki K1 Z650. I have the following

Replace the points and condencer with a dyna ds2-2 electronic more no more setting them.125.00 at z1enterprises.

Posted on May 15, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Need the pin to pin wiring schematics for this model of motorcycle?

    More images for 1990 Kawasaki 650R wiring schematic

    Kawasaki Motorcycle Wiring Diagrams -
    Kawasaki Motorcycle Electrical Wiring Diagram Schematics. ... Kawasaki GPZ600 GPZ 600 Electrical Wiring Harness Diagram Schematic 1988 to 1990 HERE ...Kawasaki KZ650 Z650 KZ Z 650 B Electrical Wiring Harness Diagram Schematic ...

    Owner Center - Kawasaki

Jan 21, 2016 | Motorcycles

1 Answer

Hello,i need to purchase 1 litre of super candy red paint for my kawasaki z650

Cycles Unlimited, Decatur, Al. should be able to get it for you. #256 - 355 - 1459.

Jun 25, 2014 | 1977 kawasaki Z 650

1 Answer

Need a key for a 1978 z650

I'd be checking with the Kawasaki dealer. Or a locksmith... Either way finding the right key any other way is going to be extremely hard if not impossible... Hope it helps...

Sep 07, 2013 | kawasaki Kawasaki Motorcycle Key

1 Answer

Trying to find a 1981 Kawasaki KZ650 csr owners manual

Oct 08, 2012 | kawasaki Z 650 Motorcycles

1 Answer

Hi, i have a 1996 Kawasaki zx900-b3 and the marks on the petrol tap have worn off and i'm not sure when its on or or off or on reserve. i've only had the bike a few days so not used to it...

The tap on the tank is longer on one end than the other.

Long end hanging down is on
Long end Horizontal is off
Long end pointing up is reserve

Jul 29, 2011 | kawasaki ZX-9R Motorcycles

1 Answer

I would like to know the torque wrench settings for the front and rear disc brake studs on a z650 c3 please.

Hi do you mean the caliper fastening bolts, if so the 10 mm diamiter bolt torqe will be 24-26 ft pounds Or 33n meters

Mar 02, 2011 | 1979 kawasaki Z 650

2 Answers

I have a Kawasaki K1 Z650. I have the following

Check the tappett clearances they may be too tight ,also reset the points to the correct gap 0.6 mm should be ok

Mar 03, 2010 | 1978 kawasaki Z 650

1 Answer

Can unleaded fuel be used in a Kawasaki Z650?

yes but if it starts to run a little different jst tune it to suit the unleaded

Jul 29, 2009 | 1984 kawasaki Z 650

2 Answers

I have a 1978 Kawasaki KZ750 B3 Twin. I am currently trying to resolve an issue with it right now. I am trying to determine why the bike does not get any spark. I've replaced the points and condenser and...

The rectifier has no effect on the ignition system if the battery is fully charged. If you have access to a test light or voltmeter, check for power (12 volts) at one of the coil side-connections with the key turned on. If no voltage at either coil connection, then power is not coming from key switch. Check plug connections at key switch--may be loose or corroded from water entry. Do headlights, horn, starter work? Key switch should have one "always hot" connection which comes from battery. Wire colors should match through each connector. Hope that helps.

Jul 10, 2009 | 1981 kawasaki KZ 1300 A3

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

141 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers


Level 3 Expert

77186 Answers


Level 2 Expert

342 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides