Question about Harley Davidson FLHX Street Glide Motorcycles
The oil tank is full, no pressure and the oil lamp is on
Posted by Anonymous on
Hi Anonymous, start by checking oil level in tank and make sure it is between the add and full mark. With engine at normal operating temperature 180-230 degrees and the use of a 10 micron synthetic media oil filter, oil pressure will be 30-38 psi at 2,000 RPM and 3-5 psi. at idle. The oil pressure light is designed to come on at 2 psi. or less. To accurately test oil pressure remove oil pressure sending unit and install known good oil pressure gauge that reads 0-50, there might possibly be some plumbing required for hard to access points. If you are out in the middle of nowhere and there is no cell phone service and your oil pressure gauge isn't working and your oil pressure light is burned out, despair not, you still have one last line of defense left HYDRAULIC LIFTERS, as long as those tireless workers are quiet, you have oil pressure, maybe not much, but enough to get you down the road at a slow to moderate speed using the least amount of RPMS as necessary. Good luck
Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e
Posted on Jun 06, 2015
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
Several things could be at play: Type or weight of oil, confirm this first. Not to question the rebuild but if not done properly (improper bearing clearances, too large) the oil pressure can be low and perhaps a worn pump too. While I am unfamiliar with the engine and oil pump loaction I'd check it if your able too. You'll probably need a good set of feeler gauges to check this if these clearances are outside of the pumps limits the pump will be less able to create pressure; this is of course more evident when the oil heats up.
Another cheap fix is to use a heavier weight oil.
Hope this might help,
Posted on Aug 21, 2009
What's your miles between changes?1500 to 2500 miles 1 qt. aint bad.Are you injected?do computer thing for ign/timing and air/fuel settings.If you're carb do jet cleaning and check float bowl setting.Check that float isn't leaking[full of fuel].Check plugs for good color and look for black residue in rear pipe,signs of bad air/fuel mixture and bad burning plug[coil voltage].If your carb doesn't have float check setting of rod that operates the fuel diaphragm.Do computer check for ign timing.Yea, if the plugs are oil fouled then forget what I said bout oil consumption.Baby it till winter and get top end done.Don't worry,2007 is too new for a top end.General tune-up should fix you up.New coils maybe.
Posted on Mar 28, 2010
Tips for a great answer:
Sep 10, 2014 | 2007 Harley Davidson FLHX Street Glide
Sep 27, 2013 | 2000 Harley Davidson FLHTCUI Electra Glide...
Jul 10, 2013 | Harley Davidson FLHX Street Glide...
Jan 30, 2013 | 2000 Harley Davidson FLHTCUI Electra Glide...
Jul 06, 2012 | 2011 Harley Davidson FLHX Street Glide
May 21, 2012 | 2010 Harley Davidson FLHX Street Glide
Oct 08, 2011 | 2006 Harley Davidson FLHXI Street Glide
Aug 14, 2011 | 2008 Harley Davidson FLHX Street Glide
Sep 16, 2010 | 2008 Harley Davidson FLHX Street Glide
May 09, 2010 | 2008 Harley Davidson FLHX Street Glide
91 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: