Question about 2006 kawasaki KX 250

Open Question

Torque specs fork bolts

Looking for torque specs on 06 kx 250 2 stroke, top and bottom fork tube clamps

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
bunnydawg
  • 5158 Answers

SOURCE: 91 kx 250 torque values

Engine Top End:
Auto Decompressor Bolt 104 in·lb
Cylinder Head Cover Bolts 87 in·lb
Cylinder Head Bolts: M10 36 S
M6 104 in·lb S

the S in that means the specified pattern ... just like tightening car tire bolts... please note all that it its INCH lbs....

don't know why it says just 36 for the M10 bolts unless they left out inch lbs

Anything else let me know as i've got a manual for the 250 f... actually i've got a few different ones

Robert

Please take a moment to rate this solution as i've taken a few minutes to find the manual thanks

Posted on Jan 28, 2009

Ad
robotleg
  • 9 Answers

SOURCE: torque specs

what size bolt heads on these bolts (the bolts size chart for correct torque specs is 2mm smaller than the head of the bolt on Kaw).while the forks are still off and the end caps also still off,hold them level (up/down) and by hand (which will be easy because the caps are off to let the springs come out past the tube-but leave them in as they change the amt. of fluid goin in)push down slow to compress and bottom them out then fill till you get 100mm from inside the top of the forks tube is on the mark.then pull them back to fully extended ,put the caps CAREFULLY back on so they dont stripp the soft threads up.P.S.if this was used at a track there are 2 inexpensive brass or copper bushings inside the big tubes top and a bit lower that will get worn and let the inner fork tube **** back and fourth as it compresses in and out that causes the seals to leak again very soon because it flexes the round inner part of the fork seal to become out of round (not tight all around the tube for correct sealing) from slack and to much movement from the above mentioned cheap bushings wear.I cut em out with a dremmel and freeze the new ones for easy insertion with fingers to not nick em from tappin in with a hammer,etc.good luck,wallace

Posted on Jul 26, 2009

  • 78 Answers

SOURCE: what are the torque specs

The torque specs for your cylinder base nuts are 25ft.-lb.and the head flange nuts at 18ft.-lb.tighten them in criss cross pattern,at three different stages,ex.25ft.-lb.start with 8 then15 then 25,18ft.-lb.start with 5 then 10 then 18.good to go.Hope this helps.

Posted on Feb 08, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is fork pinch bolt torque on yz 2006 250 yamaha


Hi, Anonymous for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
ANybody know the torque values of Triple clamp pinch bolts Yamaha 2 Stroke
complete list of 05 YZ250 torque specs Yamaha 2 Stroke
YAMAHA YZ250 LC Owner Service Manual
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-yz-owners-manuals

Feb 18, 2013 | 2003 Yamaha YZ 250

1 Answer

What is 2006 yz 250 fork pinch bolt torque


Hi, Anonymous for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
http://mybikemanuals.com/yamaha/yamaha-yz-owners-manuals
OEM parts for Yamaha
YAMAHA YZ250 LC Owner Service Manual
complete list of 05 YZ250 torque specs Yamaha 2 Stroke
ANybody know the torque values of Triple clamp pinch bolts Yamaha 2 Stroke

Feb 18, 2013 | 2003 Yamaha YZ 250

1 Answer

What is the axle torque settings on the front an rear axle bolts on a 2007 ktm 250 xc?


Thank you for contacting FixYa with your inquiry.
I have compiled a list of all the useful KTM torque setting that apply to your bike.

KTM Torque settings


  1. Collar screw, front wheel spindle Front axle nut 40Nm 30ft lbs
  2. Brake Caliper front Brake Caliper front Loctite 243 2 19ft lbs
  3. Brake Disk, front Brake disk front Loctite 243 1 11ft lbs
  4. Brake Disk, rear Brake disk rear Loctite 243 1 11ft lbs
  5. Clamping screws, upper fork bridge Top triple clamp 20Nm 15ft lbs
  6. Clamping screws, lower fork bridge Bottom triple clamp 15Nm 11ft lbs
  7. Clamping screws, fork stubs Front axle pinch bolts 10Nm 7ft lbs
  8. Collar nut, rear wheel spindle Rear axle nut 80Nm 59ft lbs
  9. Hex nut swingarm bolt Swingarm nut 100Nm 74ft lbs
  10. Hex collar screw handlebar clamp Upper handlebar clamps 20Nm 15ft lbs
  11. Allen head screw handlebar support Lower handlebar clamps Loctite 243 4 30ft lbs
  12. Shock absorber top Shock absorber top bolt 60Nm 44ft lbs
  13. Shock absorber bottom Shock absorber botton bolt 60Nm 44ft lbs
  14. Sprocket screws Rear sprocket bolts Loctite 243 3 25ft lbs
  15. Ball joint for push rod Rear brake pedal pivot Loctite 243 1 7ft lbs
  16. Engine mounting bolts Engine mounting bolts 45Nm 33ft lbs
  17. Engine brace Engine brace 33Nm 24ft lbs
  18. Screw adjusting ring spring preload Shock preload collar bolt 8Nm 6ft lbs
  19. Spoke nipple Spokes 5Nm 4ft lbs
  20. Other Screws on chassis M6 10Nm 7ft lbs
  21. M8 25Nm 19ft lbs
  22. M10 45Nm 33ft lbs
  23. Other collar nutes on chassis M6 15Nm 11ft lbs
  24. M8 30Nm 22ft lbs
  25. M10 50Nm 37ft lbs
  26. Front Sprocket 44ft lbs
Let us know if we can provide further assistance.
Best regards,
TF

Jul 05, 2011 | KTM 250 XC Motorcycles

1 Answer

CYL HEAD BOLT TORQUE SPEC AND CAM HOLDER BOLT SPECS.


Thank you for contacting FixYa with your inquiry. I have been going
over some of the older help requests that have been archieved and
trying to provide solutions for those that didn't get answered. Hope
this information helps.

KTM Torque settings


  1. Collar screw, front wheel spindle Front axle nut 40Nm 30ft lbs
  2. Brake Caliper front Brake Caliper front Loctite 243 2 19ft lbs
  3. Brake Disk, front Brake disk front Loctite 243 1 11ft lbs
  4. Brake Disk, rear Brake disk rear Loctite 243 1 11ft lbs
  5. Clamping screws, upper fork bridge Top triple clamp 20Nm 15ft lbs
  6. Clamping screws, lower fork bridge Bottom triple clamp 15Nm 11ft lbs
  7. Clamping screws, fork stubs Front axle pinch bolts 10Nm 7ft lbs
  8. Collar nut, rear wheel spindle Rear axle nut 80Nm 59ft lbs
  9. Hex nut swingarm bolt Swingarm nut 100Nm 74ft lbs
  10. Hex collar screw handlebar clamp Upper handlebar clamps 20Nm 15ft lbs
  11. Allen head screw handlebar support Lower handlebar clamps Loctite 243 4 30ft lbs
  12. Shock absorber top Shock absorber top bolt 60Nm 44ft lbs
  13. Shock absorber bottom Shock absorber bottom bolt 60Nm 44ft lbs
  14. Sprocket screws Rear sprocket bolts Loctite 243 3 25ft lbs
  15. Ball joint for push rod Rear brake pedal pivot Loctite 243 1 7ft lbs
  16. Engine mounting bolts Engine mounting bolts 45Nm 33ft lbs
  17. Engine brace Engine brace 33Nm 24ft lbs
  18. Screw adjusting ring spring preload Shock preload collar bolt 8Nm 6ft lbs
  19. Spoke nipple Spokes 5Nm 4ft lbs
  20. Other Screws on chassis M6 10Nm 7ft lbs
  21. M8 25Nm 19ft lbs
  22. M10 45Nm 33ft lbs
  23. Other collar nuts on chassis M6 15Nm 11ft lbs
  24. M8 30Nm 22ft lbs
  25. M10 50Nm 37ft lbs
  26. Front Sprocket 44ft lbs
TF

Apr 28, 2011 | 2008 KTM 450 SX-F

1 Answer

Head torque specs.on 1991 KTM540 2-stroke


Thanks for contacting FixYa. I was reviewing some of the older un-answered questions trying to ensure your issue has been resolved.

KTM Torque settings


  1. Collar screw, front wheel spindle Front axle nut 40Nm 30ft lbs
  2. Brake Caliper front Brake Caliper front Loctite 243 2 19ft lbs
  3. Brake Disk, front Brake disk front Loctite 243 1 11ft lbs
  4. Brake Disk, rear Brake disk rear Loctite 243 1 11ft lbs
  5. Clamping screws, upper fork bridge Top triple clamp 20Nm 15ft lbs
  6. Clamping screws, lower fork bridge Bottom triple clamp 15Nm 11ft lbs
  7. Clamping screws, fork stubs Front axle pinch bolts 10Nm 7ft lbs
  8. Collar nut, rear wheel spindle Rear axle nut 80Nm 59ft lbs
  9. Hex nut swingarm bolt Swingarm nut 100Nm 74ft lbs
  10. Hex collar screw handlebar clamp Upper handlebar clamps 20Nm 15ft lbs
  11. Allen head screw handlebar support Lower handlebar clamps Loctite 243 4 30ft lbs
  12. Shock absorber top Shock absorber top bolt 60Nm 44ft lbs
  13. Shock absorber bottom Shock absorber botton bolt 60Nm 44ft lbs
  14. Sprocket screws Rear sprocket bolts Loctite 243 3 25ft lbs
  15. Ball joint for push rod Rear brake pedal pivot Loctite 243 1 7ft lbs
  16. Engine mounting bolts Engine mounting bolts 45Nm 33ft lbs
  17. Engine brace Engine brace 33Nm 24ft lbs
  18. Screw adjusting ring spring preload Shock preload collar bolt 8Nm 6ft lbs
  19. Spoke nipple Spokes 5Nm 4ft lbs
  20. Other Screws on chassis M6 10Nm 7ft lbs
  21. M8 25Nm 19ft lbs
  22. M10 45Nm 33ft lbs
  23. Other collar nutes on chassis M6 15Nm 11ft lbs
  24. M8 30Nm 22ft lbs
  25. M10 50Nm 37ft lbs
  26. Front Sprocket 44ft lbs

TF

Sep 03, 2010 | KTM MXC 520 Racing Motorcycles

1 Answer

I need engine torque settings on my 2008 ktm sxf 250 motorcross bike


Thank you for contacting FixYa with your inquiry. I have been going
over some of the older help requests that have been archieved and
trying to provide solutions for those that didn't get answered. Hope
this information helps.

Try these:

KTM Torque settings


  1. Collar screw, front wheel spindle Front axle nut 40Nm 30ft lbs
  2. Brake Caliper front Brake Caliper front Loctite 243 2 19ft lbs
  3. Brake Disk, front Brake disk front Loctite 243 1 11ft lbs
  4. Brake Disk, rear Brake disk rear Loctite 243 1 11ft lbs
  5. Clamping screws, upper fork bridge Top triple clamp 20Nm 15ft lbs
  6. Clamping screws, lower fork bridge Bottom triple clamp 15Nm 11ft lbs
  7. Clamping screws, fork stubs Front axle pinch bolts 10Nm 7ft lbs
  8. Collar nut, rear wheel spindle Rear axle nut 80Nm 59ft lbs
  9. Hex nut swingarm bolt Swingarm nut 100Nm 74ft lbs
  10. Hex collar screw handlebar clamp Upper handlebar clamps 20Nm 15ft lbs
  11. Allen head screw handlebar support Lower handlebar clamps Loctite 243 4 30ft lbs
  12. Shock absorber top Shock absorber top bolt 60Nm 44ft lbs
  13. Shock absorber bottom Shock absorber bottom bolt 60Nm 44ft lbs
  14. Sprocket screws Rear sprocket bolts Loctite 243 3 25ft lbs
  15. Ball joint for push rod Rear brake pedal pivot Loctite 243 1 7ft lbs
  16. Engine mounting bolts Engine mounting bolts 45Nm 33ft lbs
  17. Engine brace Engine brace 33Nm 24ft lbs
  18. Screw adjusting ring spring preload Shock preload collar bolt 8Nm 6ft lbs
  19. Spoke nipple Spokes 5Nm 4ft lbs
  20. Other Screws on chassis M6 10Nm 7ft lbs
  21. M8 25Nm 19ft lbs
  22. M10 45Nm 33ft lbs
  23. Other collar nuts on chassis M6 15Nm 11ft lbs
  24. M8 30Nm 22ft lbs
  25. M10 50Nm 37ft lbs
  26. Front Sprocket 44ft lbs
TF

Oct 29, 2009 | 2008 KTM 250 SX-F

1 Answer

What is te torque specs for the camshaft retaining bolts


Thanks for contacting FixYa. I was reviewing some of the older un-answered questions trying to ensure your issue has been resolved.

KTM Torque settings


  1. Collar screw, front wheel spindle Front axle nut 40Nm 30ft lbs
  2. Brake Caliper front Brake Caliper front Loctite 243 2 19ft lbs
  3. Brake Disk, front Brake disk front Loctite 243 1 11ft lbs
  4. Brake Disk, rear Brake disk rear Loctite 243 1 11ft lbs
  5. Clamping screws, upper fork bridge Top triple clamp 20Nm 15ft lbs
  6. Clamping screws, lower fork bridge Bottom triple clamp 15Nm 11ft lbs
  7. Clamping screws, fork stubs Front axle pinch bolts 10Nm 7ft lbs
  8. Collar nut, rear wheel spindle Rear axle nut 80Nm 59ft lbs
  9. Hex nut swingarm bolt Swingarm nut 100Nm 74ft lbs
  10. Hex collar screw handlebar clamp Upper handlebar clamps 20Nm 15ft lbs
  11. Allen head screw handlebar support Lower handlebar clamps Loctite 243 4 30ft lbs
  12. Shock absorber top Shock absorber top bolt 60Nm 44ft lbs
  13. Shock absorber bottom Shock absorber botton bolt 60Nm 44ft lbs
  14. Sprocket screws Rear sprocket bolts Loctite 243 3 25ft lbs
  15. Ball joint for push rod Rear brake pedal pivot Loctite 243 1 7ft lbs
  16. Engine mounting bolts Engine mounting bolts 45Nm 33ft lbs
  17. Engine brace Engine brace 33Nm 24ft lbs
  18. Screw adjusting ring spring preload Shock preload collar bolt 8Nm 6ft lbs
  19. Spoke nipple Spokes 5Nm 4ft lbs
  20. Other Screws on chassis M6 10Nm 7ft lbs
  21. M8 25Nm 19ft lbs
  22. M10 45Nm 33ft lbs
  23. Other collar nutes on chassis M6 15Nm 11ft lbs
  24. M8 30Nm 22ft lbs
  25. M10 50Nm 37ft lbs
  26. Front Sprocket 44ft lbs

\TF

Oct 28, 2009 | 2008 KTM 450 SX-F

1 Answer

Need torque specs for the triple tree bolts holding the fork tubes top and bottom. 2009 Honda VTX 1300 C


20 nm on all of them this may not seem alot but the clamps bend over the forks and clamp onto them many thanks buddy

Sep 12, 2009 | 2005 Honda VTX 1300 C

1 Answer

Torque specs


what size bolt heads on these bolts (the bolts size chart for correct torque specs is 2mm smaller than the head of the bolt on Kaw).while the forks are still off and the end caps also still off,hold them level (up/down) and by hand (which will be easy because the caps are off to let the springs come out past the tube-but leave them in as they change the amt. of fluid goin in)push down slow to compress and bottom them out then fill till you get 100mm from inside the top of the forks tube is on the mark.then pull them back to fully extended ,put the caps CAREFULLY back on so they dont stripp the soft threads up.P.S.if this was used at a track there are 2 inexpensive brass or copper bushings inside the big tubes top and a bit lower that will get worn and let the inner fork tube **** back and fourth as it compresses in and out that causes the seals to leak again very soon because it flexes the round inner part of the fork seal to become out of round (not tight all around the tube for correct sealing) from slack and to much movement from the above mentioned cheap bushings wear.I cut em out with a dremmel and freeze the new ones for easy insertion with fingers to not nick em from tappin in with a hammer,etc.good luck,wallace

Jul 26, 2009 | kawasaki KX 125 Motorcycles

Not finding what you are looking for?
2006 kawasaki KX 250 Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

76691 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...