Question about Motorcycles

1 Answer

Starter Clutch My Starter Clutch needs replaced....Do I have to replace the whole assembly or can I just get the piece I need?

Posted by on

  • Dee Rauch May 13, 2013

    Oh..Sorry...2001 Yamaha XVS1100 Classic

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Motorcycles Master
  • 3,799 Answers

Just get the piece you need. But you don't mention the make and model of your motorbike. So, I can't be entirely sure.

Posted on May 11, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 7 Answers

SOURCE: Drawing or Schematic on Suzuki Lt50 Recoil Starter Assembly

This may help you a bit.
01a2e10.gif

Posted on Feb 04, 2009

wd4ity
  • 4565 Answers

SOURCE: Need to replace clutch cable on a 2002 H-D Dyna,

To replace the cable, you are going to have to remove the cover on the end of the right side of the transmission. Just follow the cable and see where it goes into transmission. You may have to remove exhaust pipes to do this. The threaded cable end screws into this cover. If the handlebars are the stock type bars, simply replace with a stock cable. If the bars have been changed, you'll have to match the overall cable length to get the right cable.

Posted on Sep 24, 2009

miket756
  • 2702 Answers

SOURCE: 1985 gs 550 l starter clutch replacement

yes,,, drop it in the repair shop it the easy way forwards, but if cash is tight, go and buy a repair book for your bike but you will still need tools to do the job right, and its not easy to do,,, get a pall to do it for you???? and give him a drink for it?

Posted on Oct 24, 2009

co7196
  • 3433 Answers

SOURCE: starter clutch is going bad

can you take a picture of it and e-mail it to co 7196@yahoo.com?

Posted on Nov 12, 2009

  • 26 Answers

SOURCE: could anyone email me a shop manual for a 1992 yahmaha 750 virago

this shows all the parts of the bike exploded, however no tolerences. I'll see if i can find a proper manual around. Try this link for now...
http://www.cmsnl.com/yamaha-xv535-virago_model16855/

Posted on Apr 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need instructions on replacing the whole clutch


Remove all tension from the cable. Drain the fluid and remove the primary outer cover. Remove the primary chain adjuster. Remove clutch adjustment plate cir-clip and plate assembly . Lock compensatory and clutch sprockets. Loosen and remove compensator and clutch hub assembly nuts and assemblies. Remember that the clutch nut is a left hand thread.

Oct 07, 2014 | Harley Davidson Motorcycles

1 Answer

Starter clutch nut on gsf 1200 w reg is it a left or right handed thread


If you damaged the starter clutch, you very well may have bent the crankshaft... you REALLY need to take this bike to a QUALIFIED PROFESSIONAL and tell them what happened.. let them check it out..and then SHOW YOU what they find..

Jul 15, 2017 | Suzuki GSF 1200 Bandit N Motorcycles

1 Answer

The air condition wont turn on. The windows dont work, and the spedometer doesnt work


This just happened to me yesterday. First, push the AC button to turn the AC off. Then, find the fuse pannel on the driver's side under the dash. Mine is behind the ash tray. Replace the 10 amp fuse (marked fuse #18 on my 1995 Camry manual) and the windows, spedo, tach, etc will come back on. My problem is the bearings on my AC clutch heated up a plastic piece between the AC clutch and AC compressor and the plastic piece blew up and sprayed hot plastic all around the AC compressor. The car runs, but no AC and if I push the AC button, the fuse blows again. I am planning to unbolt the compressor from the engine block, and replace the clutch assembly and pully without disconnecting the hoses. Disconnecting the hoses will vent coolant to the atmosphere and require professional equipment to clean the oil from the system, pull a vaccuum and recharge the system. The AC compressor clutch assembly is available at Advanced Auto for $98. The whole compressor is $247 but requires a lot of work to recharge. You could also take the clutch assembly or whole compressor off and just leave it off and get a shorter (40" in my case) belt to go just to the alternator.
Good Luck.

Jun 25, 2011 | 1995 Toyota Camry

1 Answer

Need diagram to put on starter drive clutch ***.for 1985 1340cc harley


To replace the starter drive clutch on your 1985 model Big Twin, first disconnect the battery. Drain the primary and remove the primary cover. Remove the starter drive shaft that has the clutch on it. Clamp the drive shaft in a vise equipped with soft jaws and remove the nut from the end of the shaft. The nut is the round piece on the end that has two flats for a wrench to fit. It has LEFT HANDED THREADS. Remove the starter drive and replace it with a new unit. Replace the nut using Loctite 271 red and put the starter drive shaft back in. Make sure you purchase a good starter drive clutch. Avoid the Chinese units as they don't hold up very well. If you need a diagram, go to this site. http://www.bikebandit.com/1985-harley-davidson-fxst/o/m1502#sch209973

Good Luck
steve

Apr 13, 2011 | 2000 Harley Davidson FLSTC Heritage...

1 Answer

1980 yamaha 400 xs starter spins engine doesent turn over


The starter clutch needs to be replaced. At the other end of that chain is a wheel with a couple slots cut at angles. Inside each of these slots is a small cylindrical piece of metal. The whole unit fits over the end of the crankshaft and because of the angle of the slots those cylindrical pieces of metal (which move freely in the slots) will be forced against and grip the crankshaft when the starter is operated. If they become worn down they are no longer able to exert enough pressure on the crankshaft in order to turn it. Buying a starter clutch 2nd hand is not recommended. If you are unable to source one from a bike shop, try and have them made. Take the old ones to an engineering shop. Unless you know how to temper/harden metal of course.

Jul 26, 2010 | 1980 Yamaha XS 400

1 Answer

The electrical connector on the a/c unit broke off. Do I need to replace the entire a/c unit or the clutch assembly or what?


THE ELECTRICAL TERMINALS ON AC CLUTCH COIL IS BROKEN OR DAMAGED THE CLUTCH COIL HAS TO BE REPLACED.YOU DONT HAVE TO REPLACE THE WHOLE COMPRESSOR.YOU WILL NEED COIL REMOVER TOOL AND BEARING DRIVER TOOL.

Jun 18, 2010 | 1993 GMC Sierra

1 Answer

Lawn tractor, engine model 42A707, starter spins but won't start engine; noted starter gear on top is worn down. Need help to either replace whole starter assembly with gear or just gear?


I had this same problem with a twin cylinder B & S engine and was able to get just the gear drive replaced without replacing the whole starter. Hope this helps you

Nov 10, 2009 | Craftsman 20 Hp 42" Deck Lawn Tractor

1 Answer

Can the belt in the clutch be replaced or do I have to buy a new clutch and belt assembly?


You don't need to replace the whole clutch, you can replace just the belt. You can get the clutch belt and the brush roll belt combo pack for the DC07 here:

http://www.vacbelts.com/dyson-clutch-system-belt.htm

Oct 26, 2009 | Dyson DC07 Animal Bagless Upright Cyclonic...

1 Answer

Need to replace fan cluch


the radiator fan is mounted to the clutch, in other words remove the bolts / nuts that is holding the fan assembly to the water pump usually just four nuts once you pull the fan assembly the part that yo seperated from the water pump is the clutch, now remove the fan blades and mount thm on the new clutch assembly the piece which mounts tt the water ump is the fan clutch

Jul 10, 2009 | 2000 Kia Sportage

1 Answer

Sticking starting motor


If you have already tried a new starter and had the same results,I would say,you need to replace the starter clutch.If you haven't tried a new starter yet,I would say,Try that first,It's a whole lot easier to replace than the starter clutch.

Please take time to rate this fixya.

May 14, 2009 | 1985 Yamaha XJ 700 X Maxim

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

yadayada
yadayada

Level 3 Expert

76132 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...