Question about 2007 Harley Davidson FXDB Dyna Street Bob

1 Answer

Harley fuel injection

Starts up and runs smooth at idle. Give it gas and it misses and stops. What's the problem?

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Harley Davidson Master
  • 39,932 Answers

Hi Anonymous, and the usual suspects are:
1. Severely discharged or damaged battery.
2. Loose, corroded or broken battery cable.
3. Alternator not charging or below normal rates.
4. Failed ignition coil, ignition/electronic module.
5. Failed CKP, CPS, CMP, MAP, TPS, or BAS sensor.
6. Faulty ignition switch.
7. Water or dirt in fuel system, carburetor or filter.
8. Fuel tank vent system plugged or gas cap not venting.
9. Fuel tank empty.
10. Fuel valve vacuum line broken or carburator vent line closed off.
11. Restricted, blocked or kinked fuel line.
12. Failed fuel pump, pressure regulator and or fuel injectors.
For a prime suspect please visit website below and good luck:
Harley Diagnostic Codes 04 to Present

Posted on Jun 09, 2015

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

ESRACING
  • 14 Answers

SOURCE: 2003 harley davidson heritage springer

CHECK ADVANCE WAYS UNDER POINT OR INGNITION COVER. POSSIBLE INGNITION MODULE FAILURE. RECOMMEND HIFIRE INGNITION MODULE.

Posted on Nov 08, 2009

wd4ity
  • 4565 Answers

SOURCE: Need to adjust the idle on one cylinder on harley

Ok, first off, this ain't no Yamaha you're messing with. It's a completely different motorcycle in most every way. Not saying it's better or worse than the *** bike but it's different.

It has two cables, this is correct, but only one carb. One cable is the throttle cable and the other is the idle cable. The idle cable pulls the carb shut in the event the throttle plate spring breaks on the carb. It's a safety thing and it was the same way on your Yamaha.

Now, if the front cylinder is not running at idle, I would suspect a vacuum leak somewhere. There are several places where you could have a vacuum leak. Of course, the intake manifold seals could be leaking, the intake carburetor seal could be leaking, or the VOES/ petcock line could be causing a problem. Unless you have taken your air cleaner off for some reason, I'm going to assume that the problem is in the petcock.

Your bike has one of the vacuum operated petcocks in the tank unless it's been changed already. Vacuum from the engine opens the petcock allowing fuel to the carb when the engine is running but when the engine stops, the vacuum disappears and the petcock closes. Supposedly. This is the worst piece of junk Harley ever put on their motorcycles. They do two things, they quit working and won't let fuel into the tank or they cause a small vacuum leak that will cause the bike not to idle properly. I suspect you have the latter case.

Drain your fuel tank by loosening the petcock and allowing the gas to run out around it. Catch the fuel with a large funnel and an empty fuel can large enough to hold the fuel in your tank. Once empty, disconnect the two hoses and remove the petcock. On the backside of the petcock, there is a square plate. Remvove the four small screws and take the plate off. There will be a diaphragm, a spring, and needle under the plate. Remove the plate carefully so you can see how it goes back together. Hold the diphragm up to the light and gently stretch it while looking for holes. If you find a hole, you'll have to either buy a new diaphragm and repair your petcock or , better yet, replace the entire petcock with a manually operated one. A Pingle petcock is a very high quality valve and you'll like it but it is pricey. If you buy an OEM petcock, get one for a 1995 or earlier bike. You will no longer need the vacuum line and you can plug it with a small bolt or something to stop the vacuum leak.

This vacuum line comes off a nipple at the backside of the carb and it feeds vacuum to two things. It's a 3/16" hose that goes up to the VOES switch mounted on the frame under the tank. From there it "Y's" off to the smaller hose that goes to the backside of your petcock. Take your fuel tank off and inspect this hose. Look for cracks. If you go with the manual petcock, eliminate the small portion of the hose by replacing the hose that runs to the VOES with the single hose instead of the "Y'd" hose.

As for the idle speed of you engine, it should be set at about a thousand RPM. Look at the top of the carb. There is a screw near the top on the right side of the carb. That is the throttle stop screw. It controls the idle speed of the engine. Turn the screw clockwise to increase the idle speed.

Ok, try what I've written here. If it doesn't work, get back with me.

Good Luck.
Steve

Posted on Jul 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine dies idle wont start


Hi Anonymous, for more information about your question please visit the website below. Good luck and have nice day.
Harley Davidson Magneti Marelli Fuel Injection Settings

Aug 16, 2013 | Harley Davidson Motorcycles

1 Answer

Engine misses


Hi Anonymous, and the usual suspects are:
1. Spark plugs in bad condition or partially fouled.
2. Spark plug cables in bad condition or leaking.
3. Spark plug gap to close or to wide.
4. Faulty ignition coil, module and or sensor.
5. Battery nearly discharged.
6. Damaged wire or loose connections at battery terminals especially the ground cable at BOTH ends, ignition coil, or plug between ignition sensor and module.
7. Intermittent short circuit due to damaged wire insulation.
8. Water or dirt in fuel system, carburetor or filter.
9. Fuel tank vent system plugged or carburetor vent line closed off.
10. Carburetor controls misadjusted.
11. Damaged carburetor.
12. Loose or dirty ignition module connector at crankcase.
13. Faulty MAP, CKP, and or CMP sensors.
14. Incorrect valve timing.
15. Weak or broken valve springs.
16. Damage intake or exhaust valve.
For a prime suspect please visit website below and good luck:
Harley Diagnostic Codes 04 to Present

May 05, 2013 | 2011 Harley Davidson FXDB Street Bob

1 Answer

Fuel injection problems on my 2000 Harley Davidson road King


Hi Anonymous, for more information about your question please visit the websites below. Good luck and have nice day.
Harley Davidson Magneti Marelli Fuel Injection Settings

Mar 30, 2013 | Harley Davidson Motorcycles

2 Answers

Idle rpm too high


You don't say if the engine is carb or fuel injected.
If it has a carb, it could be sticking linkage for the fast idle to the choke.
If it is fuel injected it could be a faulty idle air control valve.
Or it could be something holding the throttle open like a binding cable.

Mar 03, 2013 | 1985 Toyota Pickup

1 Answer

Fuel injected harley road king dies at stoplights after it gets warm.


Hi Martinez3122, for more information about your question please visit the websites below. Good luck and have nice day.
Harley Davidson Magneti Marelli Fuel Injection Settings

Jan 27, 2013 | Harley Davidson Motorcycles

1 Answer

Gas blowing out of carb at mid throttle ,starts loping.idles fine runs good until mid throttle


Hi William, 4 out of 5 Harley Gods give this one a thumbs down, but just to be on the safe side contact your local dealers service/parts department for confirmation. Good luck and have nice day.

Jul 11, 2012 | Harley Davidson FLHT Electra Glide...

1 Answer

Blazer rumbling,choking,missing in engine


Check the fuel pressure regulator. generally "failure" position is full open which will richen up the fuel mixture. also check vacuum line to the regulator for cracks and good connection.

Jun 06, 2009 | 1995 Chevrolet Blazer

2 Answers

High Idle On Start-up.


Sounds like you have a intake leak. You're getting extra air into the mix until she fully warms up. Check where the throttle body meets the heads.

Apr 30, 2009 | 2003 Harley Davidson FLHRCI Road King...

Not finding what you are looking for?
2007 Harley Davidson FXDB Dyna Street Bob Logo

114 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...