Question about Motorcycles

1 Answer

Misfires and stalls when you let the clutch out

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 1 Answer

So does it idle fine? does it start right back up? have u removed the spark plugs and checked spark or condition of plugs. they will tell u alot depending on how they look

Posted on May 05, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

REPLACED CLUTCH ON ZR 550 CLUTCH ENGAGES , BUT WHEN FULLY RELEASED BIKE JUDDERS THEN STALLS OUT . TRY TO ADJUST & GEARS WONT ENGAGE .


So if you raise the revs to say about 4000 rpm and let the clutch out does it stall or judder or both will it engage at all and pull away ?

Mar 07, 2015 | Motorcycles

1 Answer

Car goes into gear when idling but will not move


sounds like total lost of engine power, or the brakes are frozen in ice.
if you can push car by and with brakes off , is the engine bad.
the clutch is not bad, if you stall any engine.
so what engine,, they use many on Acura's
cant fix the engine or know EFI with out that fact.
Generic.
lost compression on any or all cylinders.
bad fueling. (lost fuel pressure)
its most likely not spark if it idles nice, but doing the 60k tuneup
is real good idea now that it dont run ,now.

old sparks can work with lose speed then under load misfire.




Feb 06, 2014 | 1987 Acura Integra

1 Answer

Kia rio 2003 scanned & found p0102 faults are stalls immediately after starting, inability to acclerate, misfire


p0102=Mass or Volume Air Flow Circuit Low Input
p0300=Random/Multiple Cylinder Misfire Detected

sounds like its out of time

Sep 25, 2012 | 2003 Kia Rio

1 Answer

P1740 code on 2001 ram 1500 tcc-overdrive solenoid . how to test & replace


there is a total of 27 diagnostic steps to follow, but here is some info for you:
SYMPTOM
P1740-TCC O/D SOL PERFORMANCE

WHEN MONITORED
The Torque Convertor Clutch (TCC) and Overdrive Clutch (O/D) will be tested each time the PCM requests TCC engagement in 3rd gear and O/D.

SET CONDITION
The code will set if the expected RPM drop is not achieved while attempting to engage TCC or O/D. This indicates a malfunctioning torque convertor or overdrive clutch.

POSSIBLE CAUSES
- Camshaft DTC present
- Engine RPM DTC present
- Fuel level low
- Misfire DTC present
- Output speed DTC present
- P1765 DTC present
- Park/Neutral DTC present
- PTO engaged (if equipped)
- Torque converter clutch DTC present
- TPS DTC present
- Transfer case in low range (if equipped)
- Transmission Relay DTC present
- Transmission temperature too cold
- Intermittent
- Check transmission fluid-debris
- Check transmission fluid-stall
- 3-4 Shift Solenoid
- Oil Pan contains excessive debris
- Shaft or seal damage
- TCC solenoid
- Torque converter
var classElements = new Array(); var node = document; var tag = 'a'; var els = node.getElementsByTagName(tag); var elsLen = els.length; var pattern = new RegExp("(^'\\s)specs_note(\\s'$)"); for (i = 0, j = 0; i

Jun 03, 2011 | Dodge Ram 1500 Cars & Trucks

1 Answer

I have a 2000 dodge durango with a trouble code p1740 what does it mean


SYMPTOM
P1740-TCC O/D SOL PERFORMANCE

WHEN MONITORED
The Torque Convertor Clutch (TCC) and Overdrive Clutch (O/D) will be tested each time the PCM requests TCC engagement in 3rd gear and O/D.

SET CONDITION
The code will set if the expected RPM drop is not achieved while attempting to engage TCC or O/D. This indicates a malfunctioning torque convertor or overdrive clutch.

POSSIBLE CAUSES


Camshaft DTC Present
Engine RPM DTC present
Fuel level low
Misfire DTC present
Output speed DTC present
P1765 DTC present
Park/neutral DTC present
PTO engaged (if equipped)
Torque converter clutch DTC present
TPS DTC present
Transfer case in low range (if equipped)
Transmission relay DTC present
Transmission temperature too cold
Intermittent
Check transmission fluid-debris
Check transmission fluid-stall
3-4 shift solenoid
Oil pan contains excessive debris
Shaft or seal damage
TCC solenoid
Torque converter

Aug 15, 2010 | Dodge Durango Cars & Trucks

1 Answer

06 COBALT STALLS WHEN I STOP AHHHHHHHHHHHH


Easy fix... Take a gallon of gas and a clean cloth or shirt. Soak the cloth in the gas and wipe all the interior down with the gas.

Then poor some of the gas all over the engine, making sure to soak it really good

After doing this, take a match and burn that f**ker..
Mine was doing the same thing, I burned it and blamed it on Islamic jihad to my insurance. Never looked back

Mar 24, 2009 | 2005 Chevrolet Cobalt

1 Answer

Clutch/misfire problem


bring to local garage and let them av a look

Nov 07, 2008 | 2004 Audi A4

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

74945 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...