Question about kawasaki Motorcycles
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
you dont need torque specs on that just use a 1/2 inch drive with you 14mm or16mm socket hold the wratchet right at the top and tighten it as tight as you could get it like that then use wratchet in normal position and just give it a little snugg it will be perfect i have done it a million time on the same type of bikes...
Posted on Dec 05, 2008
SOURCE: 91 kx 250 torque values
Engine Top End:
Auto Decompressor Bolt 104 in·lb
Cylinder Head Cover Bolts 87 in·lb
Cylinder Head Bolts: M10 36 S
M6 104 in·lb S
the S in that means the specified pattern ... just like tightening car tire bolts... please note all that it its INCH lbs....
don't know why it says just 36 for the M10 bolts unless they left out inch lbs
Anything else let me know as i've got a manual for the 250 f... actually i've got a few different ones
Please take a moment to rate this solution as i've taken a few minutes to find the manual thanks
Posted on Jan 28, 2009
The 8mm head bolts are torqued at 19 - 21 ft/lbs.
any smaller 6mm bolts are torqued to only 6 ft/lbs
like those on the lower cylinder.
Posted on Aug 22, 2009
you can call the Suzuki dealer for the specs and/or buy a tech manual for that bike. (and work on your spelling, "cylinder")
Posted on Oct 09, 2009
Tips for a great answer:
Feb 26, 2014 | Holley 1975-1987 Ford F-250 Carburetor,...
for the head
Step 1: Bolts 1 - 8 to 61 N·m (45 ft. lbs.)
† Step 2: Bolts 1 - 8 to 88 N·m (65 ft. lbs.)
† Step 3: Bolts 1 - 8 (again) to 88 N·m (65 ft. lbs.)
† Step 4: Bolts 1 - 8 turn an additional 1/4 Turn.
(Do not use a torque wrench for this step.)
NOTE: Bolt torque after 1/4 turn should be over 122
N·m (90 ft. lbs.). If not, replace the bolt.
Bolts . . . . . . . . . . . . . . . . . . . .23 N·m (200 in. lbs.)
Intake Manifold Gasket Retaining
Screws . . . . . . . . . . . . . . . . . .12 N·m (105 in. lbs.)
Intake Manifold Plenum
Bolts . . . . . . . . . . . . . . . . . . . .28 N·m (250 in. lbs.)
the pivot arm ? whats that
Nov 13, 2010 | 2001 Chrysler Voyager
Nov 04, 2010 | 2005 Yamaha WR 250 F
Aug 25, 2010 | 1996 Acura Integra GS-R
Nov 24, 2009 | 2001 Kia Sportage
Aug 20, 2009 | 2003 Suzuki RM 250
Jun 01, 2009 | Sharp EL-531VB Calculator
34 people viewed this question
Usually answered in minutes!