Question about 2005 KTM EXC 300

1 Answer

Plug keeps glogging up - 2005 KTM EXC 300

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 127 Answers

Carb problems, improper jetting, to much oil in mix, filthy air filter

Posted on Jan 07, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

94.lexus ls400- keeps pushing radiator coolant out of overflow,


Your radiator could be glogged and causing it to back up out of overflow,drain coolant,if still good,save and remove bottom hose from radiator get hose and insert in radiator and let run and see how flow is,if clooged,go to autozone and tell them what is happening and they will get you what you need to unglog .To check water pump,unscrew radiator cap and put over opening,crank engine,let it get at operating temperature,remove cap and check flow.Click on link to view radiator flush. http://www.autozone.com/autozone/accessories/Fluids-and-Chemicals/Radiator-Cleaner-and-Additive/_/N-262g?filterByKeyWord=radiator+flush&fromString=search

Oct 20, 2012 | 1994 Lexus LS 400

1 Answer

My whirlpool waqshine mac hine wont come on and is full of water


Are you getting any codes on the panel? most likely either your pump filter is glogged on front loaders, or the pressure switch located on the inside of your control panel is not functioning on top loaders. If you can blow through the tube connected to the switch and it is not plugged, then the suspect is the sensor. Could also be the main control board had died. Need more info here. Thanks

Mar 23, 2011 | Washing Machines

1 Answer

The thread is loaded into the bobbin however it keeps looping around the thing that the bobbin sits on.


On bobbin holder is a small screww to set the bobbin tention, must be set (tighten) if too loose it will glog up if too tight it will break the thred. wcbotha@yahoo.com

May 11, 2010 | Brother LS-2125 Mechanical Sewing Machine

1 Answer

Filter screen on carb of a poulan pro chainsaw keeps glogging with a white powder. Carb has been cleaned and only used briefly. Use recommeded gas and 2 cylce oil mix.


Hello. If this powder is very fine saw dust its an indication of the filter doing its job. It may collect oil as well and create a paste like coating. Cleaning every 8 hours of use should be adequate.
builderdale

Jan 11, 2010 | Poulan Pro 42CC 2 Cycle Chainsaw, 18"

1 Answer

My jeep keeps cutting off could it be my fuel line


sounds like the fuel filter is clogging up. if fuel filter is clooged up, usually when car is turned off the dirt from filter settles on bottom. then when it is started the dirt is up to filter and it glogs up.

Nov 23, 2009 | 2000 Jeep Grand Cherokee

1 Answer

Gas Dryer turns off Heat after 10 min running


the best way is to take off front and the top, remove the belt from the pully and motor,make sure door is closed and drum removed. Start the dryer and allow to run looking and listening it could just be glogged in the blower section,. If it still stops it's the motor,if not its iethieg glogged our the pullies belt and tensioner need replacing if its a whirlpool, it could also be a back bering....

Mar 12, 2009 | Dryers

1 Answer

Psc1410 printer light stays on


remove the main plug
and again replug it and check it
if the light still glogs then try pressing off button several times tat wil work

Mar 08, 2009 | HP Office Equipment & Supplies

Not finding what you are looking for?
2005 KTM EXC 300 Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top KTM Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4525 Answers

Brian Anderson

Level 3 Expert

365 Answers

Are you a KTM Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...