Question about 2008 Hyosung GT250R

1 Answer

08 hyosung gt250r starting issue

Am having a courious issue with getting my bike start. All lights and indicators are working fine. New battery as of Dec. When it is running it holds volts between 13 and 15. holds 11 to 12 when the bike is off so the battery is good. when i hit the ignition switch, nothing happens. sometimes i will hear a click. the bike still starts with a push/bump start method. what is throwing me off with the whole situation, is that if i hook a set of jumper cables up to the bike from my truck, the bike fires up right away without any issues. am at a lost because it starts with a jump, if the starter was bad or the ignition switch wasnt getting power, the extra juice from the truck shouldnt make a differnece. the last idea i have is to try running new power and ground wires. perhaps they are old and arent pushing a good current...

Posted by on

  • ron bresett May 06, 2013

    had starter solenoid checked, thats still good. followed all wires from solenoid to ignition switch, all seem good

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Hyosung Master
  • 39,960 Answers

Hi, Ron and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, needs to be 12.5 volts or better and be able to pass a "LOAD" test if necessary.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
5. Tip over sensor needs a reset.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand or clutch pull in switch/sensor.
9. Starter control circuit, relay, or solenoid faulty.
10. Main fuse or circuit breaker may be blown or faulty.
11. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
https://www.perthstreetbikes.com/forum/showthread.php?t=140128
Hyosung GT250R not starting
HYOSUNG COMET 125 Service Manual
http://www.alpha-sports.com/hyosung_parts.htm
http://www.hyosung.com.au/downloads/manuals/GT250.pdf

Posted on Mar 15, 2017

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

seanpwright
  • 2030 Answers

SOURCE: 2008 hyosung wont start

I am assuming you mean with the starter button.

If thats the case check that you have power to the button, and if so powewr coming out of the button.

If all is good this far, check the starter solenoid and starter for operation.

try taking 12v directly to the starter and see what happens..if it turns then the problem is before the starter.

Posted on Sep 11, 2009

mastatech
  • 478 Answers

SOURCE: I have a carburated 2008 hyosung gt250r that cant start!!!!

I would say the clicking is not the battery but next to or above it is a starting relay which from your discription has gone out. You can locate it by following the large red wire comimg from the battery. The soleniod can be tested by jumpering from one side of the soleniod to the orthersid use a pair of needle nose pliers. If it turns over its diffinitly the culpert. Just change it out and ride on. They use a low amperage coil to close this larger load of the starter circuit.

Posted on Jul 15, 2010

  • 200 Answers

SOURCE: my 2008 hyosung gt250r will

short in wiring or switch causing battery discharge. charge battery to full charge . see if everything works right. ifturn lights
still dont work, un hook switch to turn signals . wait for the next
day and see if your battery has held charge . should read 12v
or 11.5v . if battery stays up switch maybe shorting out. check wiring for chaffing

Posted on Oct 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2010 Hyosung Gt250r carb flooding when I try to ride but idles good only on start up what's causing this?


Hi, Chris and the usual suspects are:
1. Dirt or other foreign matter between float valve and its seat.
2. Float valve sticking.
3. Float valve and/or valve seat is worn or damaged.
4. Float misadjusted.
5. Float cracked, leaky or damaged.
6. Excessive "PUMPING" of hand throttle grip.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Why is the engine bogging under acceleration Suzuki FA50 Moped
will gv250 carbys fit gt250r
http://files.hyosungmotorsusa.com/GT125_250_Service_Manual.pdf https://www.alpha-sports.com/Parts/H_GT250R.htm
HYOSUNG GT250 FI Owner Manual

Feb 18, 2017 | 2010 Hyosung GT250R

1 Answer

Hi mate my hyosung gt250r started randomly stalling while I was ridding, thought it was the kickstand cable, yesterday I went to start it started fine but cut off when I put it in gear, Anny ideas why


It does sound like a kickstand sensor issue, as the sensor only works when the bike is in gear. To check, you can bypass the sensor by disconnecting it's cable and then joining the two wires together so there's a permanent electrical connection. If that solves the problem, you need a new kickstand sensor.

May 12, 2015 | Hyosung Motorcycles

1 Answer

Hyosung GT250R Tacho not working


These bikes are never senen with many miles on them when for sale, invariably they have issues uncommon to a newer bike, this sis due to the workmanship and metalurgical issues etc, they are clones but thats where the similaritys end, they nevr last from all I ever saw of these bikes.
If you mean loses power on hills due to clutch slippage, the springs i know get weak fast and lose tension sufficient to engage fully thus allowing plates to slip and losing power to the rear wheel, if you mean otherwise nobody can tell you this way correctly.

Feb 25, 2012 | 2007 Hyosung GT250R

1 Answer

2011 Hyosung GT250R instruments keep resetting


Hi, Kingsley for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Hyosung GT250R clock repair
HYOSUNG COMET 125 Service Manual
HYOSUNG GT 250 Service Manual
https://www.alpha-sports.com/Parts/H_GT250R.htm
HYOSUNG GT 125 Manual

May 12, 2017 | 2011 Hyosung GT250R

1 Answer

I have a problem with my hazard relay it is the second one that went on my hyosung gt250r in one week. I replaced it with an origenal part from hyosungsource but the relay starts clicking as soon as I...


You have a crossed wire someplace in your wireharness. go back to the dealer and make them change it - it should be under warranty if you bought it new.

Jan 06, 2012 | 2009 Hyosung GT 250

1 Answer

2008 Hyosung GT250R will not turn over


Hi, Mcle_cool before testing any electrical component in the Starting System it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead acid batteries.
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
4. Bank angle sensor needs a reset or is faulty.
5. FOB battery low or dead.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand or clutch pull in switch/sensor.
9. Security alarm needs a reset.
10. Starter relay, solenoid, starter have failed or circuit wiring faulty.
11. Starter armature or field coils have failed.
12. Main fuse or circuit breaker may be blown or faulty.
13. The electric starter is working but starter clutch has failed.
14. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
https://www.perthstreetbikes.com/forum/showthread.php?t=140128
Hyosung GT250R not starting
HYOSUNG COMET 125 Service Manual
https://www.pdf-archive.com/2015/08/16/manual-reparaci-n-gt250ri/manual-reparaci-n-gt250ri.pdf
https://www.alpha-sports.com/Parts/H_GT250R.htm
HYOSUNG GT 125 Manual

May 23, 2017 | 2008 Hyosung GT250R

1 Answer

I haven't started my bike in almost 1 year. The starter does not even turn engine. I replaced battery and lights work. No noise at all when I press starter.


i have a 2007 gt250r and had a similar problem, on the right side beside the battery between the fairing and the frame is the starter solenoid, you can test it with a test light by putting the clamp of the test light on one side then the light on the other side, hit the starter button if the light doesnt come on it is the solenoid, about $50 off ebay

Aug 10, 2011 | 2008 Hyosung GT250R

1 Answer

My 2008 hyosung gt250r will not start but i can push it off and it works great and shifts fine and the lights go dim when the bike is not running and the brake light and head lights work but the blinkers...


short in wiring or switch causing battery discharge. charge battery to full charge . see if everything works right. ifturn lights
still dont work, un hook switch to turn signals . wait for the next
day and see if your battery has held charge . should read 12v
or 11.5v . if battery stays up switch maybe shorting out. check wiring for chaffing

Oct 21, 2010 | 2005 Hyosung GT 250

2 Answers

My 2008 hyosung gt250r doesnt start, all light and horn works. any solutions


does it crank over?....if so check spark...fuel...etc...try to narrow it down to a actual problem such as carbs clogged, or injector not working, other than wont start, not able to tell much from that.

Sep 11, 2009 | 2005 Hyosung GT 250

2 Answers

Hi i have a hyosung gt650r only push starts.....


the battery is charging ok if not the bike wouldnt run-ur starter motor needs inspection-maybe the rotor or brushes r froze-1st chec wiring that gos to the starter-could be loose or bad-with a manual u can disasemble n test the motor-ni dong ma zai jian

Aug 17, 2009 | 2005 Hyosung GT 250

Not finding what you are looking for?
2008 Hyosung GT250R Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyosung Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Hyosung Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...