Question about Harley Davidson Motorcycles

1 Answer

Right spot light not working

No current to bulb on right side,left side works

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,799 Answers

Check the cables from the relay. One is broken.

Posted on May 03, 2013

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 4 Answers

SOURCE: left side turn signals ( front & Back) won't work

Check the bulb for the actual indicator light on the dash

Posted on Jul 16, 2009

  • 11 Answers

SOURCE: signal lights flashing fast but dim on left side,

Hi,
Make sure you have no wires chaffing against the frame or threads of bolts along the wires' path. Make sure your connections are clean and tight.

If you have a multimeter, take some resistance readings and also, ensure that all your grounding wires are in good shape and tighten any bolts or screws along the way.

Measure across the leads of the headlight, if it reads -infinity- (ohms) the bulb needs replacing, if you get a reading the bulb is fine and you need to start looking elsewhere...

Good luck,

Obe

Posted on Aug 26, 2009

DoubleClutch
  • 376 Answers

SOURCE: right rear turn signal has power to the bulb but

I would have to say it would be the ground wire in that turn signal. You are getting a ground with the tester so to test this take a piece of wire and find the ground side of the socket for the bulb wich is the housing that holds the bulb in. Take the wire and strip both ends. Insert the bulb and touch the housing with one end and the other end touch it to a good ground on the bike and if it lights then you have a bad ground somwhere.

Posted on Nov 01, 2009

wd4ity
  • 4565 Answers

SOURCE: Only right turn signal works.

Ok, there is only a few things that could cause this. They include:

handlebar directional switch on inoperative side not functioning.
broken or disconnected wire in the directional switch circuit
a possible combination of causes found in problem #1.
module malfunction.

You need to test the left turn signal switch to make sure it has voltage going to it and when you press the switch, 12 volts is going to the turn signal cancelling unit. This 12 volt pulse from the switch is what tells the module to turn the left turn signals on. Without the pulse, the module doesn't know you've pressed the switch. You may need a wiring diagram to trace this out. Sorry but I don't have one for that year model.

Good Luck
Steve


Posted on Nov 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1992 chevy c1500 with light issues. Left turn signal works fine, right side blinks like 4 ways,along with license plate light.when head lights are on nothing for right side turn signals. Hazards...


It seems to be a ground defect on right side. Do you have the same bulb's number . What about the front flasher. remove right rear lamp assembly remove connector measure voltage between ground and current .reconnect it measure voltage at bulb socket. you should find your problems
hope it helps

Dec 07, 2014 | 1992 Chevrolet C1500

2 Answers

2007 ml320 cdi left brake light will not come on


It is apparent that the wire between the current sensor that the computer monitors and the left brake light socket is open. Thus the computer knows the brake light is not working because it is not drawing current. If you have a wiring diagram, you can probably find the broken wire or bad connection. This may take some time. To get the left brake light working, you can jumper the left brake light socket to the right brake light socket. Warning, this may cause the computer to register the extra current on the right side as a short circuit and shut both off. If that happens you will have to forgo the left brake light until you get the open circuit corrected.

Apr 22, 2014 | 2007 Mercedes-Benz ML320 CDI

2 Answers

Only rear driver side brake light will not work when braking need help


Pastor Norman, Pastor Dave here.
Since you already replaced the left rear brake light bulb and that didn't help, please take that bulb socket out again as you did before, and find a way to test the bulb contact for electricity when the brake lights are on. You should get 12 volts out of the "hot" metal contact.
If the other two lights are on, and you have no current in the socket, you either have a bad socket, or a broken wire somewhere.
One way is to go back a few inches and skin off the insulation of the brake light wire and see if there is current back a few inches from the socket. Cover with tape when you finish.
If you decide to cobble a solution, you could run a good wire from the other brake light that works and splice it in to the dead wire.
Be Blessed.

Jan 23, 2013 | 2007 Toyota Corolla

1 Answer

On my `06 Dodge Ram 1500 my left LOW beam doesn`t work ALL other lights work fine. Only low beam on drivers side. I tried 3 new bulbs,didn`t help.


You probably have a bad plug or a broken wire on the low beam of the left side. I would replace the plug for the bulb and run a wire from the low beam on the right side or , locate and bypass the bad section of wire going to the current plug if the plug is still good.

Nov 05, 2010 | 2001 Dodge Stratus

1 Answer

Brake light, reverse light and turn signal issues


Hello. The symptoms you are describing are likely due to a poor ground. Temporarily install a new ground wire by securing a piece of copper wire to the frame with a self tapping screw. Use this ground wire along with the hot wire to see if each of these lights works. If it does, trace the ground wire back to the frame, unscrew it and clean up the metal with emery cloth so you reestablish a good ground.

Jan 28, 2010 | 2003 Ford Windstar

2 Answers

Headlight one side works on bright the other side works on dim


Try swapping the headlight bulbs or buying a known good bulb and testing that way. Sounds like a shorted bulb filament issue.

Apr 05, 2009 | 2004 Oldsmobile Alero

4 Answers

Turn Indicator won't work when headlights on!


Double check the bulb numbers. Check all the bulbs and make the numbers from the right and left are the same. (Left side is OK so that number is probably correct) Then if the numbers are correct, check the installation of the bulbs. Many bulbs have 2 filaments if installed backwards it could cause the problem. 

Mar 24, 2009 | 1992 Chevrolet S-10

1 Answer

1999 dodge caravan


Do you own a test light? Check for power at wires behind socket? Clean socket good , check contact spots for bulb & clean any rusty side of the socket with emery cloth, or sandpaper, for good contact also.

Jun 25, 2008 | 1999 Dodge Caravan

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...