Question about 2000 Honda XL 1000 V Varadero

Open Question

Exhaust pipes baffles

How do u remove the baffles from the standerd xhaust pipes

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to remove baffle


Most baffles can be un-screwed from the rear; some others from the inside after removing the exhaust.

Jul 12, 2015 | 2006 Triumph Rocket III

1 Answer

How do i remove the double baffles per pipe on the Keeway/BigBoy Superlight 200?


You will need to cut it open and weld it back up its the only way to do it properly.

Feb 22, 2015 | Big Motorcycles

1 Answer

How to remove baffles 2004 Harley davidson electra glide


If you have stock pipes you can't just remove the baffles . Some people on a budget will take a hammer and a Peace of pipe and knock out the piece that's blocking the center of the exhaust pipe which will give you more sound , but I don't recommend this I really recommend getting some slip ons.

May 20, 2014 | 2004 Harley Davidson FLHTCUI Electra Glide...

1 Answer

My suzuki gsxr 1000 k3 will start then cut out six times before it runs properly on its own in the cold


Instructions
  1. Take Down
    • 1 Park the motorcycle on the kickstand or center stand and allow the exhaust pipes to cool completely.
    • 2 Refer to your Suzuki service manual and organize the metric tools needed to remove the baffle. On newer models, it may be necessary to remove the tailpipe section to modify the baffle. On older models, you may be directed to remove a bolt that secures the baffle in the tailpipe.
    • Follow the procedure given in the manual and remove the tailpipe section or slide-in baffle using the appropriate tools. Save any brackets or bolts. Place the tailpipe or baffle on a workbench.
    Tailpipe Baffles
    • 4 Hold one end the tailpipe up to a light and look inside the other end. Depending on the baffle, you may see very little light or none at all. Modifying the baffle is a matter of opening up areas in the baffle.
    • 5 Chuck a 1/4-inch drill bit in an electric drill. Use a bit extension if necessary to reach deep into the tailpipe with the drill bit.
    • 6 Place the tailpipe on a workbench. Use a towel or rags to prevent scratching the finish. Insert the tip of the drill bit into the tailpipe and drill a 1/4-inch hole in the baffle.
    • 7 Hold the tailpipe up to the light again. Determine the number of additional holes you want based on the purpose of the modification. Drill additional holes in the baffle if needed.
    • 8 Stand the tailpipe on end and tap it on the workbench to clear the debris from drilling out of the baffle. Make sure all debris is cleared out before reinstalling the tailpipe on the motorcycle.
    Slide-In Baffles
    • 9 Secure the outer end of the baffle in a bench vise with the baffle extending to one side. The outer end has the threaded hole where the bolt was removed to take the baffle out of the exhaust pipe.
    • 10 Measure the length of the baffle and divide it by four. You modify a slide-in baffle by cutting off a one-quarter section at a time using a hacksaw. Mark the baffle at the one-quarter point and cut the first section off the end.
    • 11 Reinstall the baffle in the exhaust pipe using the saved bolt and the metric tool.
      Start the motorcycle and determine if the modification produced the desired result.
    • 12 Allow the exhaust pipe to cool completely before removing the baffle for further modification. Most likely, cutting one or two quarter sections will give you the result you want. Avoid cutting too much off the baffle, or it will be useless.

Jan 17, 2013 | Motorcycles

1 Answer

Are the outer forks the same on a gsx 1400 k4 as. K5 ?


Instructions
  1. Take Down
    • 1 Park the motorcycle on the kickstand or center stand and allow the exhaust pipes to cool completely.
    • 2 Refer to your Suzuki service manual and organize the metric tools needed to remove the baffle. On newer models, it may be necessary to remove the tailpipe section to modify the baffle. On older models, you may be directed to remove a bolt that secures the baffle in the tailpipe.
    • 3 Follow the procedure given in the manual and remove the tailpipe section or slide-in baffle using the appropriate tools. Save any brackets or bolts. Place the tailpipe or baffle on a workbench.
    Tailpipe Baffles
    • 4 Hold one end the tailpipe up to a light and look inside the other end. Depending on the baffle, you may see very little light or none at all. Modifying the baffle is a matter of opening up areas in the baffle.
    • 5 Chuck a 1/4-inch drill bit in an electric drill. Use a bit extension if necessary to reach deep into the tailpipe with the drill bit.
    • 6 Place the tailpipe on a workbench. Use a towel or rags to prevent scratching the finish. Insert the tip of the drill bit into the tailpipe and drill a 1/4-inch hole in the baffle.
    • 7 Hold the tailpipe up to the light again. Determine the number of additional holes you want based on the purpose of the modification. Drill additional holes in the baffle if needed.
    • 8 Stand the tailpipe on end and tap it on the workbench to clear the debris from drilling out of the baffle. Make sure all debris is cleared out before reinstalling the tailpipe on the motorcycle.
    Slide-In Baffles
    • 9 Secure the outer end of the baffle in a bench vise with the baffle extending to one side. The outer end has the threaded hole where the bolt was removed to take the baffle out of the exhaust pipe.
    • 10 Measure the length of the baffle and divide it by four. You modify a slide-in baffle by cutting off a one-quarter section at a time using a hacksaw. Mark the baffle at the one-quarter point and cut the first section off the end.
    • 11 Reinstall the baffle in the exhaust pipe using the saved bolt and the metric tool.
      Start the motorcycle and determine if the modification produced the desired result.
    • 12 Allow the exhaust pipe to cool completely before removing the baffle for further modification. Most likely, cutting one or two quarter sections will give you the result you want. Avoid cutting too much off the baffle, or it will be useless.

1_16_2013_4_34_52_am.jpg

Jan 15, 2013 | Suzuki GSX 1400 Motorcycles

1 Answer

Cutting streetfighter exhaust removing baffle xjr 400


Hi, Jonathan for more information about your question and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Cutting out baffles on stock pipes
Exhaust Baffle Bypass Modification
Regular service manual XJR400 4HM1 4HM 000101 maintenance $62
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-xj-owners-manuals

Jul 14, 2011 | 1998 Yamaha XJR 400

1 Answer

I want more sound from my pipes (australian specs).. how do i knock the restrictions out of the mufflers?


If you remove the baffles from your exhaust pipes the ignition timing and tuning will need attention or it will run rough.
I find it best to buy Screaming Eagle pipes or Slash Cut pipes, they have the correct resistance for backpressure but are very loud!!!!
If you wish to remove the baffles, the procedure will depend on the design of the pipes. There is usually a "pop" rivet somewhere underneath them that if you drill it out the baffles will pull out.
In the UK they fail their roadworthyness test if they have no baffles.
Loud pipes save lives, ride safe!

Nov 28, 2010 | 2000 Harley Davidson FLSTC Heritage...

1 Answer

Pulsar 150 - Some knocking after i got a service 3 days back...


It could be the exhaust baffles which are in the exhaust pipe tht have given away, you can remove the exhaust pipe assy and get it cut underneath and get the baffles electric welded..or rather spot welded and weld the exhaust back but the chrome will burn off and rust may thn take over ..or unless you paint tht area black( heat ressistant paint.),or better off is to replace the complete exhaust pipe assy.
Hope this helps!

Sep 22, 2009 | 2005 Bajaj Pulsar 180

2 Answers

Loss of power with new exhaust


You didn't say if the new exhaust was the factory stock unit for your bike or an aftermarket pipe. The aftermarket pipes are generally not well manufactured. The factory pipes are well made but even they have internal flaws at times.

The flow of exhaust gasses is being held back by the baffles in the muffler. Some mufflers have an end baffle that can be removed from the end of the pipe. If one is present, remove it. This may help. Aside from that, return the new pipe and ask for a refund or replacement.

Apr 17, 2009 | 2006 Gilera Runner VX 125

Not finding what you are looking for?
2000 Honda XL 1000 V Varadero Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75807 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...