Question about Motorcycles

1 Answer

Can i have my problem answered

Front and rear driving lights don't work

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Motorcycles Master
  • 8,404 Answers

Sure, what is your question?

Posted on May 03, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1991 celica and for some reason the front signals does not work at all. When I turn on the blinkers it blink really fast on both sides but hazard light works fine it blinks normal but it...


check the main earth wire near the battery. and one near the rear of the lights. unbolt them and clean the connectors up put some grease on them after. then check again. remember that when the earth wires come off the radio code will be needed to reset the the radio. be safe and take the battery off.

Sep 28, 2013 | Cars & Trucks

2 Answers

My tail lights on my 1999 chevy venture work when they won't to and I think it's a ground short.. But I don't know where to look for it!


get a wiring diagram, follow this circuit, wire by wire, start @ rear, your tail lights, check each bulb, then proceed to front, along frame rail, to switch & fuse block. test for continuity & shorts, bad wires, corrosion, etc

Jan 18, 2013 | Cars & Trucks

1 Answer

Service lights don't come on


check wire connections at light with ohm meter and at switch if replacing the bulb doesn't work

Oct 31, 2012 | 2004 Subaru Forester

1 Answer

Front dome light and overhead driver and passenger lights don't work


Hopefully this is what you're looking for...good luck! :) http://wiki.answers.com/Q/Where_can_you_find_a_fuse_box_diagram

Aug 27, 2012 | 2005 Hyundai Sonata

1 Answer

My ABS/Brake light in dashboard is on .


I didn't have that issue,but I had a 1992 dakota with
rear abs only & I just unplugged the module under the dash

I'm all for diagnosing everything & having it factory stock & working

But you don't need abs on a 4x4 that old & the rear hydraulic
abs unit ,gets so rusty that it is sad.

If you ever replace rusted brake tubing, remove it

They don't check that in inspection

Jun 06, 2012 | 1999 Dodge Ram

1 Answer

Rear brakes are noisy while driving


The job wasn't done correctly,that is obvious

Most places don't remove any rust so parts slide
as they should ,nor do they lube anything

I have worked on brakes for 50 years come july & never
had a noise or hot,no issues

When you say changed out,that's what you got
It is called hanging pads,slap them on & done.

You have brake hoses & claipers to consider,parking
function,etc

If they don't release for some reason,you have heat & noise
Sloppy work

May 21, 2012 | 2008 Dodge Nitro

1 Answer

Front wheels not turning in 4wheel drive 1996 dodge dakota


Check and make sure the transfer case is adjusted right If the front end was broke you would know it. Jack up one front wheel and put it in 4wheel drive but not lock and see if the front drive shaft turns if it doesn't you need to adjust linkage or if it's electric make sure the signal is getting to the transfer case. If it only locks front and rear jack up one rear wheel also and do the check. Most people with 4 wheel drive don't know they have two wheel drive One in the rear and one in the front unless you ordered a locking dif from the factory they don't come this way. Then you would have 3 wheel drive

Dec 02, 2011 | 1996 Dodge Dakota

1 Answer

Turn signal lights not working. turn on emergency flashers and the right signal flashes and bath back lights and the front right flash but the left front don't. any idea's


The 2 filament on the LH Front turn signal is most likely burned out, ...........or the ground to it, & the entire socket needs replaced. Caution lights, send signals to ALL FRONT & REAR lights. All turn signal lights must be in working order, as it is a "pulsating" currect surge sent to the bulbs, LH or RH, depending which direction you wisk to turn. If 1 filament is broken, the circuit is incomplete, & no flash will occur. Usually you will get one light that stays on, & the front or rear missing lighting, is the one whichis the culpret.

Aug 29, 2011 | 2001 Ford F150 Styleside SuperCrew

2 Answers

Can a transmission be removed from the truck without removing the motor?


woodchuckswo, You don't state here if the truck is front or rear wheel drive but the answer to your question is yes. If it is front wheel drive, then you will have to support the engine from above before you remove the transmission. If it is rear wheel drive then you need not support the engine as it will be supported by the engine mounts. Good luck with this.

Aug 06, 2011 | Ford F-100 Cars & Trucks

1 Answer

I have phase linear uv8, need to know how to get subs 2 work! Amp goes into protect mode when rca's r plugged in, there r 3 sets of preamp out puts 1 front left and front right, 2nd is rear left rear...


try testing the amp without speakers plugged in. Run the sub preamp out to the amp that you will drive the subs with, but don't wire up the subs yet. Test for protect mode kicking in.
Yes - unplug the rca ins from the amp. retest.
No - Problem lies within the sub wiring. What is the load on the amp (measure with an ohm meter)? If it is below 4ohms, chances are the amp can't dip that low. Give it more resistance by wiring it differently (series vs. parallel)

Bruce

May 05, 2011 | Kicker Car Audio & Video

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75744 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...