Question about Harley Davidson FXSTS Springer Softail Motorcycles

1 Answer

Torque specs harley

Neck bearing r & r service

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Harley Davidson Master
  • 40,868 Answers

Hi Anonymous, and your torque specifications are:
1. 1/4" bolts 10 ft lbs.
2. 5/16" bolts 20 ft lbs.
3. 3/8" bolts 35 ft lbs.
4. 7/16" bolts 55 ft lbs.
5. 1/2" bolts 75 ft lbs.
For more information about your question please visit the website below. Good luck and have nice day.
Steering head bearings how to replace and adjust

Posted on Jun 19, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: torque specs for derby , inspection cover, &

what is the torque specs for a derby cover on my 2009 Soft tail?

Posted on Jul 27, 2009

wd4ity
  • 4565 Answers

SOURCE: Need the torque specs on clutch for a 85 FLHTC

The torque specs are the same as with any Evolution engine. The compensator sprocket 150-165 foot pounds.
Clutch hub nut (left handed threads) 60-80 foot pounds.

Use Loctite 271 on threads. Two lines in nut on Compensator and one line in clutch hub nut.

Posted on Sep 24, 2009

Mitchy123
  • 216 Answers

SOURCE: need torque specs

tighten in a cross pattern in 5 lb incrments to 40 ft lbs

Posted on Oct 22, 2009

fawkwindows
  • 96 Answers

SOURCE: what are the torque specs on a 2001 harley fat boy

Maximum Torque: 106 Nm (78.2 ft. lbs) @ 3200 rpm

Posted on Dec 13, 2009

bjgarra
  • 69 Answers

SOURCE: front end shakes how to inspect and replace neck

to inspect, lift front of ground, grab forks and shake up and down and side to side. there should be little movement if at all. to replace u need special tools and the service manual(and alot of grease).

Posted on Aug 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Harley torque specs


The best source for torque specs and assembly order is the service manual. $80 for the book is a worthwhile investment for a $20,000 bike.

Aug 12, 2014 | 2007 Harley Davidson FLHRC Road King...

1 Answer

2010 street glide rocker box torque specs and underneath rocker box torque specs


Hi Anonymous, you are going to need tools for this procedure, the first and very best tool you will ever buy should be a factory service manual. For just $5.50 you can download one at the website below:
http://harley.manuals.cc/
Good luck

Apr 07, 2014 | 2010 Harley Davidson FLHX Street Glide

1 Answer

Torque specs for front & rear axle 2004 heritage


Hi Toninbud, front axle 50-55 ft lbs. rear axle 60-65 ft lbs. Have nice day.

Feb 22, 2013 | 2004 Harley Davidson FLSTC - FLSTCI...

1 Answer

I have a 1979 kz400 and i am replacing the bearings in the neck i got the bike with it tore apart already and i am not sure if i am missing any parts and how it all goes together.thank you


Hi will...this is a job you can't afford to make mistakes on, only to find out later the hard way, worse case would be an accident and you are injured.... I don't know what parts you have now, or how it was taken apart. You should have upper and lower head bearings, several washers, flat & star, some bushings and seals, retainers and lockdown, dustcover...also bearing races. Are the new bearings tapered or non? Have the old bearing races been removed or still on the shaft? I recommend you get a shop manual and follow step by step instructions, clean, lube and torque everything to factory specs. The proper torque is VERY important ... better to be safe than sorry when it comes to steering head repairs...good luck, i hope this helps

Jul 12, 2011 | kawasaki KZ 1300 A3 Motorcycles

1 Answer

I have a 2006 Harley Dyna, was wondering if front fork torque specs are the same as Sportster front fork specs? I have quite a gap between triple tree and goose neck...fork lock pin doesn't line up in...


You didn't say which Dyna series bike you have but I'm going to say that Sportster specs are not the same as for a Dyna. If you think you have a gap between your triple tree and the steering head of the bike, something may not be assembled correctly. I'd take to a shop or a dealer and have them check the front end.

Good Luck
Steve

Jun 11, 2011 | Harley Davidson FXD Dyna Super Glide...

1 Answer

What are the torque specs for the push rods on a 1993 sportster


Pushrods on a completely stock 1993 are one piece and have no torque spec as they are not of the adjustable variety. If you do in fact have "adjustable pushrods" and have set the adjustment according to the pushrods manufacturer's specification in conjunction with a good Harley service manual the nuts on the pushrod need to be good and snug........Tight, but do not bear down on the wrenches. Use your best judgement.

Aug 04, 2010 | 1993 Harley Davidson XLH Sportster 883

1 Answer

Need to know torque spec. on main & rod bearings 4 cycl.


1997 Nissan/Datsun Truck Pickup 2.4L SFI 4cyl

The Main Bearing Cap Torque:

38 Foot pounds (Final torque)

The Rod Bearing Cap Torque:

Torque sequence:
Step 1: Torque to 10-12 Ft/Lbs
Step 2: Torque to 28-33 Ft/Lbs

Hope help with this (remember rated this post). TY for using Fixya.

May 19, 2010 | 1997 Nissan Pickup

1 Answer

Torque specs for derby , inspection cover, &


what is the torque specs for a derby cover on my 2009 Soft tail?

Jul 09, 2009 | 2003 Harley Davidson FXDL Dyna Low Rider

1 Answer

Need torque specs for 1999 Ford 3.0 rod & main bearings


ft lbs

Main Bearing Cap Bolts 75-85 56-62
Connecting Rod Cap Nuts 31-39 23-28

May 27, 2009 | 1999 Ford Taurus

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

136 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...