Question about 2007 Suzuki GSR 600

Open Question

Procedure to remove fuel tank on a GSR 600 2007 model

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How To Drain Fuel Tank On 2005 Jeep Liberty Gas Tank


here is the Cherokee page.
read chapter, 14, page 19 on..
shows all way there, and is not easy.
why do this.
is pressure low
pump dead
is there 12vdc to pump cranking, (no? then dont do this)

http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

i have the KJ pages here. (line # messed up)
Two different procedures may be used to drain fuel
tank: through the fuel fill fitting on tank, or using a
scan tool.
The quickest draining procedure involves removing
the rubber fuel fill hose (7) (Fig. 25) from fuel tank
fitting.
As an alternative procedure, the electric fuel pump
may be activated allowing tank to be drained at fuel
rail connection. Refer to DRB scan tool for fuel pump
activation procedures. Before disconnecting fuel line
at fuel rail, release fuel pressure. Refer to the Fuel
System Pressure Release Procedure for procedures.
Attach end of special test hose tool number 6541,
6539, 6631 or 6923 at fuel rail disconnection (tool
number will depend on model and/or engine application).
Position opposite end of this hose tool to an
approved gasoline draining station. Activate fuel
pump and drain tank until empty.
If electric fuel pump is not operating, fuel must be
drained through fuel fill fitting at tank. Refer to following
procedures.
(1) Release fuel system pressure.
(2) Raise vehicle.
(3) If equipped, remove fuel tank skid plate.
(4) Thoroughly clean area around fuel fill fitting
(6) (Fig. 26) and rubber fuel fill hose (1) at side of
fuel tank. After cleaning, loosen fuel fill hose clamp
(2) at tank.
(5) Before removing rubber hose (1) (Fig. 26) from
fitting, note hose orientation while referring to marks
(3) and (4).
6) Disconnect rubber fuel fill hose at fuel tank fitting
(2) (Fig. 27). Using an approved gas holding
tank, drain fuel tank through this fitting.
Tank Removal
(1) If equipped, remove fuel tank skid plate and
tow hooks. Certain equipment packages will also
require removal of the trailer hitch. Refer to Tow
Hooks, Trailer Hitch or Skid Plate in 23, Body for
removal/installation procedures.
(2) Disconnect and separate fresh air tube (6) (Fig.
28) quick-connect fitting.
(3) Disconnect air tubes at front of NVLD pump
(9) (Fig. 28).
(4) Disconnect NVLD pump (9) (Fig. 28) electrical
connector.
(5) Disconnect fuel pump module electrical connector
jumper. This is located near front of fuel tank.
(6) Support tank with a hydraulic jack.
(7) Remove 4 fuel tank strap bolts (10) (Fig. 28) (2
at front of tank; 2 at rear of tank), and remove both
tank support straps.
(8) Carefully lower tank a few inches.
(9) Continue lowering tank while guiding remaining
hoses and lines through plastic isolator sleeve (3)
(Fig. 29).
(10) If fuel tank is to be replaced, remove NVLD
pump and fuel pump module from tank. Refer to
Fuel Pump Module Removal/Installation procedures.
end , tank out.

why not login to alldata.com and read
or buy the FSM,, and get all pages of chapter 14, end to end.

Oct 19, 2015 | 2005 Jeep Liberty

1 Answer

How to remove fuel tank


Procedure to remove a fuel tank depends on brand, model and year of the car. Just some examples:
How to properly remove gas tank

How To Remove Gas Tank

How To Remove The Fuel Tank

How to drain your car fuel gas tank



Sep 27, 2015 | Cars & Trucks

2 Answers

How do I remove a fuel tank from a 2004 Buick Rendezvous


First of all, there is a recall for gas tank replacement for your vehicle. The dealer will replace it free. The link will get you to the document in PDF form
Redirect Notice
It looks like there is a bracket on one end of the tank hidden by a heat shield
0601244b03-002.jpg
FUEL SUPPLY SYSTEM Fits Buick Rendezvous

Feb 08, 2015 | 2004 Buick Rendezvous

1 Answer

Need info on how to change a 2000 Cadillac


REMOVAL PROCEDURE
TOOLS REQUIRED
A J 34730-1A Fuel Pressure Gauge
A J 39765 Fuel Sender Lock Nut Wrench
CAUTION: Refer to Batterry- Disconnect Caution in Service Precautions.
1. Disconnect the negative battery cable.
2. Relieve the fuel system pressure. Refer to the Fuel Pressure Relief Procedure. See:
Fuel Delivery and Air Induction/Fuel Filter/Fuel Pressure Release/Service and
Repair
3. Drain the fuel tank. Refer to Fuel Tank Draining Procedure. See: Fuel Delivery and
Air Induction/Fuel Tank/Service and Repair/Procedures
4. Remove the fuel tank.
5. Remove the fuel sender assembly.
6. Disconnect the fuel pump electrical connector (5).
7. Remove the fuel level sensor electrical connector retaining clip (6).
8. Disconnect the fuel level sensor electrical connector (7) from under the fuel sender
cover.
9. Remove the fuel level sensor retaining clip (4).
10. Squeeze the locking fangs and remove the fuel level sensor (3).
INSTALLATION PROCEDURE
1. Install the fuel level sensor (3).
2. Install the fuel level sensor retaining clip (4).
3. Connect the fuel level s ens oi electrical connector (7).
4. Connect the fuel level sensor electrical connector retaining clip (6).
5. Connect the fuel pump electrical connector (5).
6. Install the fuel sender assembly.
7. Install the fuel tank.
8. Refill the fuel tank.
9. Install the fuel filler cap.
10. Connect the negative battery cable.
11. Inspect for leaks.
11.1. Turn ON the ignition for 2 seconds.
11.2. Turn OFF the ignition for 10 seconds.
11.3. Turn ON the ignition.
11.4. Inspect for fuel leaks. 55dcc1df-120b-4a37-b63b-a35953989584.png

Aug 29, 2014 | Cars & Trucks

2 Answers

Is the fuel pump on a 1989 GSR galant servicable? this one seems blocked.


This fuel punp is not removed by dropping the take like so many. It is under an access panel under the rear seat. To change the fuel pump follow these instructions.
1. Determine which fuel pump your Mitsubishi Galant will need. This depends not only on the make and model, but also the engine size.

2. Prepare your car for service to the fuel pump. Relieve the fuel system pressure and disconnect the negative battery cable with a socket wrench. Take out the rear seat cushion. You will need to pull the seat stopper out and lift up the lower cushion. You can now remove the access cover.
3. Unplug the fuel pump's electrical connection and disconnect the fuel send and return hose. Remove the retaining cap for the fuel pump with tool MB991480 and remove the fuel pump.
4. Install the packing material on the fuel tank. Replace it if the packing material is damaged or deformed. Install the new fuel pump and align the marks on the floor pan and fuel pump.

5.
Complete the installation by reversing the removal procedure.

This should take care of you. Let me know if this helped you.

Mar 07, 2011 | 1989 Mitsubishi Galant

1 Answer

Ihave a 1991 honda civic hb and i think i"m having problems with my fuel pump .on this model can i get to the pump from the back seat of this vehicle or due i have to drop the gas tank. also whereis the...


you must remove the fuel tank. see procedure below.

The fuse and relay should be in the engine compartment relay box. Check fuses 2 and 14. The relay might be labeled PGM-FI

1988-91 MODELS

The fuel pump is located in the fuel tank.
  1. Disconnect the negative battery cable.
  2. Relieve the fuel system pressure.
  3. Raise and safely support the vehicle.
  4. Remove the fuel tank drain bolt and drain the fuel into a suitable container.
  5. On Civic models (except CRX and Wagon) unplug the fuel pump electrical connector in the trunk. On CRX, remove the storage compartment and unplug the fuel pump electrical connector. On Civic Wagon, remove the rear seat and carefully disengage the fuel pump electrical harness.
  6. On Civic Wagon with 4WD, remove the driveshaft from the rear differential and the exhaust pipe and muffler.
  7. Remove the 2-way valve cover and fuel hose protector.
  8. Unbolt the fuel lines.
  9. Place a suitable support under the fuel tank.
  10. Remove the fuel tank strap nuts and let the straps hang.
  11. Remove the fuel tank.
  12. Remove the fuel pump mounting nuts and the fuel pump.

To install:
  1. Install the pump assembly into the tank and make sure the unit is properly sealed.
  2. Install the tank into the vehicle and tighten the strap nuts. Connect the hoses and wiring.
  3. On 4WD vehicles, connect the driveshaft and the exhaust system.
  4. Put about three gallons of fuel into the tank and test the system.

402ec39.gif

Oct 26, 2010 | Honda Civic Cars & Trucks

1 Answer

Diagram of how to change fuel pump


highly dependent on model. Until the 80s, many pumps were on the engine. Thereafter, most pumps are inside the fuel tank. Removal usually requires lowering the fuel tank, removing all hoses and connectors, remove retaining ring, replace gage/pump unit, reverse procedure to reinstall tank.

Aug 22, 2010 | Dodge Grand Caravan Cars & Trucks

1 Answer

HOW TO TAKE A FUEL PUMP OUT A 2001 ISUZU TROOPER


REMOVAL PROCEDURE

  1. Disconnect the negative battery cable.
  2. Drain all the fuel from the tank.
  3. Install and tighten the drain plug. Tighten Tighten the drain plug to 20 N.m (14 lb ft.) .
  4. Remove the fuel tank.
  5. Remove the retaining screws from the fuel tank.
  6. Remove the fuel pump assembly from the fuel tank.
    1. Cover the fuel pump opening in order to prevent dust, dirt, or debris from entering the fuel tank.
    INSTALLATION PROCEDURE

    1. Install the fuel pump assembly. Tighten Tighten the fuel pump assembly mounting bolts to 3 N.m (27 lb ft.) .
    2. Install the fuel pump assembly retaining screws.
    3. Install the fuel tank assembly.
    4. Fill the tank with fuel.
    5. Tighten the fuel filler cap.
      1. Connect the negative battery cable.
      REMOVAL PROCEDURE # 2
      REMOVAL

      CAUTION: When repair to the fuel system has been completed, start engine and check the fuel system for loose connection or leakage. For the fuel system diagnosis, see Computers and Control Systems/System Diagnosis.

      1. Disconnect battery ground cable.
      2. Loosen fuel filler cap.
      3. Drain fuel. Tighten drain plug to the specified torque after draining fuel. Torque: 20 N.m (14 lb ft) - M8
      4. Remove fuel tank assembly (1).
      5. Remove fuel pump (FP) assembly (2) fixing screws and remove the FP assembly.
      NOTE: After removing FP, cover fuel tank to prevent any dust entering.
      INSTALLATION
      1. Install FP assembly (2).
      2. Install fuel tank assembly (1).
      3. Fill the tank with fuel and tighten fuel filler cap.
      4. Connect battery ground cable.

Oct 18, 2009 | 2001 Isuzu Trooper

2 Answers

Need directions on replacing 2000 dodge durange 4.7 ltr fuel pump


WHAT YOU WILL NEED TO DO FIRST IS JACK THE TRUCK UP AS HIGH AS SAFELY POSSIBLE.. BE SURE TO USE JACK STANDS THAT WAY THE TRUCK DOENT FALL OVER.. ONCE UP IN THE AIR HE WILL NEED TO TAKE THE GAS TANK OUT OF THE TRUCK.. THERE ARE TWO STRIPS HOLDING THE TANK INTO PLACE..THEN WHEN HE GETS THE TANK ON THE GROUND, REMOVE ALL THE FUEL LINES.(THERE ARE CLIPS ON THE PLASTIC LINES BE EASY) THEN WHEN HE GETS THE LINES LOOSE, THERE IS A METAL RING ON THE TOP ON THE FUEL TANK..HE CAN USE A SCREW DRIVER TO GET THE RING OFF( HE WILL SEE HOW TO TAKE IT OFF WHEN HE LOOKS AT IT) WHEN THE RING IS OFF PULL THE FUEL PUMP ASSEMBLY OUT OF THE TANK AND REPLACE THE FUEL PUMP (THE WHOLE FUEL PUMP WILL JUST NEED PULLED OUT, NO SCREWS) ..JUST REPEAT THESE STEPS BACKWARDS TO REINSTALL .. THIS SHOULD SOLVE YOUR $700 PROBLEM..GOOD LUCK AND THANKS FOR USING FIXYA.COM...KEITH..

Mar 14, 2009 | 2000 Dodge Durango

2 Answers

1999 jeep cherokee do you have to remove the fuel pump to replace


The combination Fuel Filter/Fuel Pressure Regulator is located on the fuel pump module. The fuel pump module is located on top of fuel tank.

The filter/regulator may be removed without removing fuel pump module although fuel tank must be removed.

REMOVAL
  1. Remove fuel tank. Refer to Fuel Tank Removal/Installation.
  2. Clean area around filter/regulator.
  3. Disconnect fuel line at filter/regulator. Refer to Quick-Connect Fittings for procedures.
  4. Remove retainer clamp from top of filter/regulator. Clamp snaps to tabs on pump module. Discard old clamp.
  5. Pry filter/regulator from top of pump module with 2 screwdrivers. Unit is snapped into module
  6. Discard gasket below filter/regulator.
    1. Before discarding filter/regulator assembly, inspect assembly to verify that O-rings are intact. If the smallest of the two O-rings can not be found on bottom of filter/regulator, it may be necessary to remove it from the fuel inlet passage in fuel pump module.
    INSTALLATION
    1. Clean recessed area in pump module where filter/regulator is to be installed.
    2. Obtain new filter/regulator (two new O-rings should already be installed)
    3. Apply a small amount of clean engine oil to O-rings. Do not install O-rings separately into fuel pump module. They will be damaged when installing filter/regulator.
    4. Install new gasket to top of fuel pump module.
    5. Press new filter/regulator into top of pump module until it snaps into position (a positive click must be heard or felt).
    6. The arrow molded into top of fuel pump module should be pointed towards front of vehicle (12 O'clock position).
    7. Rotate filter/regulator until fuel supply tube (fitting) is pointed towards front of vehicle (12 O'clock position).
    8. Install new retainer clamp (clamp snaps over top of filter/regulator and locks to flanges on pump module).
    9. Connect fuel line at filter/regulator. Refer to Quick-Connect Fittings for procedures.
    10. Install fuel tank. Refer to Fuel Tank Removal/Installation.
WARNING: THE FUEL SYSTEM IS UNDER CONSTANT FUEL PRESSURE EVEN WITH THE ENGINE OFF. THIS PRESSURE MUST BE RELEASED BEFORE SERVICING FUEL TANK .

Two different procedures may be used to drain fuel tank (lowering tank or using DRB scan tool).

The quickest draining procedure involves lowering the fuel tank.

As an alternative procedure, the electric fuel pump may be activated allowing tank to be drained at fuel rail connection. Refer to DRB scan tool for fuel pump activation procedures. Before disconnecting fuel line at fuel rail, release fuel pressure. Refer to the Fuel System Pressure Release Procedure for procedures. Attach end of special test hose tool number 6541, 6539, 6631 or 6923 at fuel rail disconnection (tool number will depend on model and/or engine application). Position opposite end of this hose tool to an approved gasoline draining station. Activate fuel pump and drain tank until empty.

If electric fuel pump is not operating, tank must be lowered for fuel draining. Refer to following procedures.

FUEL TANK REMOVAL
  1. Disconnect negative battery cable at battery.
  2. Release fuel system pressure. Refer to the Fuel System Pressure Release.
  3. Raise and support vehicle.
  4. If Equipped: Remove fuel tank skid plate.
  5. Remove 4 fuel hose shield mounting bolts and remove fuel hose shield from body.
    1. Remove fuel tank fill hose and vent hose clamps at fuel tank filler tube. Remove both hoses at fuel filler tube.
    2. Remove exhaust tailpipe heat shield mounting bolts and remove shield. CAUTION: To protect fuel tank from exhaust heat, this shield must reinstalled after tank installation.
    3. Place a hydraulic jack to bottom of fuel tank. WARNING: PLACE A SHOP TOWEL AROUND FUEL LINES TO CATCH ANY EXCESS FUEL .
      1. Disconnect fuel supply line from fuel extension line near front of fuel tank. Refer to Fuel Tubes/Lines/Hoses and Clamps. Also refer to Quick-Connect Fittings for procedures.
      2. Disconnect EVAP canister vent line near front of tank.
      3. Disconnect fuel pump module electrical connector (pigtail harness) near front of tank. Harness connector is clipped to body.
        1. Remove two fuel tank strap nuts. Position both tank support straps away from tank.
        2. Carefully lower right side of tank while feeding both fuel hoses through access hole in body. Fuel Tank Full And Not Drained Using DRB Scan Tool: To prevent fuel loss through hoses, keep left side of tank higher than right side while lowering. Do not allow hose openings to drop lower than top of tank.
        3. Continue lowering tank until clear of vehicle. Place tank on floor with left side (hose side) higher than right side
          1. Drain tank by removing fuel fill hose at tank. Fuel fill hose is largest of 2 hoses. Insert the drain hose (from an approved gasoline draining station) into hose opening. Drain tank until empty.
          2. If fuel pump module removal is necessary, refer to Fuel Pump Module Removal/installation for procedures.
          INSTALLATION
          1. If fuel pump module is being installed, refer to Fuel Pump Module Removal/installation for procedures.
          2. Install fuel fill/vent hoses to tank fittings. To prevent hose from kinking, rotate each hose until index mark on hose is aligned to index tang on fuel tank.
          3. Install hose clamps to hoses. Position clamps between index marks on each hose.
          4. Position fuel tank to hydraulic jack.
          5. Raise tank into position while guiding fuel fill and vent hoses into and through access hole in body.
          6. Continue raising tank until positioned to body.
          7. Attach two fuel tank mounting straps and mounting nuts. Tighten nuts to 10 Nm (90 in. lbs.) torque. Do not over tighten nuts.
          8. Install both fuel hoses to fuel fill tube. Tighten both retaining clamps.
          9. Position fuel hose shield to body. Install and tighten 4 mounting bolts.
          10. Connect fuel pump module pigtail harness electrical connector near front of tank.
          11. Connect fuel pump module supply line near front of tank. Refer to Quick-Connect Fittings for procedures.
          12. Connect EVAP hose near front of tank.
          13. Install exhaust tailpipe heat shield.
          1. Install fuel tank skid plate (if equipped).
          1. Lower vehicle and connect battery cable to battery.

Feb 08, 2009 | 1999 Jeep Cherokee

Not finding what you are looking for?
2007 Suzuki GSR 600 Logo

Related Topics:

181 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...