Question about Motorcycles

Open Question

1994 kx 250 torque specs clutch

Just replaced the clutch basket n clutch plates and needed to know what to torque the center hub bolt and clutch spring bolts too. thanks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 3567 Answers

SOURCE: Torque settings on the clutch inner hub and clutch

The clutch inner hub torque values ar 7.5Nm or 7.5n-kg or 54 ft-lb.

The clutch springs torque to 8Nm or 0.8m-kg or 5.8 ft-lb.

I don't get paid for my answers and I am only trying to help. But I do take pride in them. So if you will, > > > > A “very helpful” rating for this answer? Thanks!

Posted on Jun 13, 2009

Ad
tellme2
  • 137 Answers

SOURCE: 91 kx 250 clutch too tight

hi m8,, wen u put spring bolts and springs on,, u must do them right up ,, untill the spring is completly comprest,, ,untill the spring bolt wont do up any more,,cheers

Posted on Jan 23, 2009

bunnydawg
  • 5158 Answers

SOURCE: 91 kx 250 torque values

Engine Top End:
Auto Decompressor Bolt 104 in·lb
Cylinder Head Cover Bolts 87 in·lb
Cylinder Head Bolts: M10 36 S
M6 104 in·lb S

the S in that means the specified pattern ... just like tightening car tire bolts... please note all that it its INCH lbs....

don't know why it says just 36 for the M10 bolts unless they left out inch lbs

Anything else let me know as i've got a manual for the 250 f... actually i've got a few different ones

Robert

Please take a moment to rate this solution as i've taken a few minutes to find the manual thanks

Posted on Jan 28, 2009

  • 3567 Answers

SOURCE: i have a 98 cr250r and i just swapped the clutch

f229e55.png
Convert to other measurement standards at the site below.
http://www.online-utility.org/measures/torque_measurement_units.jsp

Posted on Jul 24, 2009

  • 31 Answers

SOURCE: toque spec for clutch springs

You can play an adjustment with your spring,the best adjustment is when your bike does't have a running cluth situation, and once you press the cluth lever and release it you'll have power just like jumping .and thats it.

Posted on May 26, 2010

Testimonial: "will try it today, thanks"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hay guys got a yamaha rx125 1978 just pulled the clutch plates out does anyone know how tight i should do the clutch springs up to ive had no luck looking on the net for the info ...cheers guy's


Hi, Chris these are metric torque specifications in the most common sizes and are measured in foot pounds.
Bolt size___Grade 4.8__Grade 8.8__Grade 10.9__Grade 12.9
6mm__________5__________8_________12_________15
8mm__________11_________20________30_________35
10mm_________21_________40________60_________70
12mm_________37_________70________105________120
14mm_________60_________110_______165________190
For more information about your question and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
DT 175 clutch basket plate bolts torque spec Vintage Enduro Discussions
DOWNLOAD Yamaha RX125 RX 125 Service Repair Workshop Manual Download... $15
OEM parts for Yamaha
Yamaha RX 125 1979
https://pt.wikipedia.org/wiki/Yamaha_RX_125

May 07, 2017 | Yamaha Motorcycles

1 Answer

What are the torque specs for the 4 pressure plate bolts for the clutch?


What year is it??

I am only familiar with newer models as per touring/six speed:

Install six bolts (5) (metric) to secure diaphragm spring
retainer to clutch hub. Alternately tighten bolts to 90-110
in-lbs (10.2-12.4 Nm).

May 09, 2014 | Harley Davidson FLHTC - FLHTCI Electra...

1 Answer

Yamaha wr200 bike clutch fitment


take clutch case off , you then see the clutch basket and you need to remove the center plate with about 6 bolts , then remove the fiber coated plates along with metal plates .. then replace first a fiber coated plate followed by a metal plate then a fiber following this until all plates are in and a fiber plate is showing ! then replace the cover plate with 6 bolts , tighten all bolts then undo the center nut with the adjusting screw and back it off until there is slight free play on the clutch leaver as you pull it and then release! lock the nut up holding the screw and try ! soak fiber plates for an hour before installing also ! cheers

Dec 04, 2013 | Motorcycles

1 Answer

Need torque specs for 02 yz 250f


Hi, Anonymous for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
YZ 250 Torque Specs
Part 23 Assembling 4 stroke Clutch Hub and primary Drive YZ250F example
YAMAHA YZ250F Owner Service Manual
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-yz-owners-manuals

Jul 22, 2012 | Yamaha YZ 250 F Motorcycles

1 Answer

Need dry clutch torque specs for a ducati monster s4


The torque spec for a chutch nut on a 900 is 180-190Nm (136 ft. lb.) The torque spec for the clutch housing bolts (presure plate) is 30-34 Nm (23 ft. lb.)

Jun 24, 2009 | 2003 Ducati Monster S4

2 Answers

Front Hub Bearing Torque specs to complete replacement


THE LUG NUT TORQUE SPEC - 140FT/LBS\
CALIPER MOUNT - 80FT/LBS
CALIPER BRACKET 129FT/LBS
AXLE NUT 177FT/LBS

Apr 24, 2009 | 2003 Chevrolet Silverado 1500

1 Answer

I need torque specs for 94 rodeo


flywheel 80-90 foot lbs (new bolts 90), press plate 45 foot lbs

Feb 14, 2009 | 1995 Isuzu Rodeo

1 Answer

91 kx 250 torque values


Engine Top End:
Auto Decompressor Bolt 104 in·lb
Cylinder Head Cover Bolts 87 in·lb
Cylinder Head Bolts: M10 36 S
M6 104 in·lb S

the S in that means the specified pattern ... just like tightening car tire bolts... please note all that it its INCH lbs....

don't know why it says just 36 for the M10 bolts unless they left out inch lbs

Anything else let me know as i've got a manual for the 250 f... actually i've got a few different ones

Robert

Please take a moment to rate this solution as i've taken a few minutes to find the manual thanks

Jan 28, 2009 | kawasaki KX 250 Motorcycles

1 Answer

91 kx 250 tight clutch


are you shure you have ALL the clutch plates?? the cable is well lubed? the pushrodbearing/adjuster may be in the middle of the clutch basket cover plate. OR you have the wrong springs installed!

Jan 23, 2009 | kawasaki KX 250 Motorcycles

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

yadayada
yadayada

Level 3 Expert

76109 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...