Question about Motorcycles

Open Question

How to remove a baffle from a laser duo tech exhaust

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to remove baffle


Most baffles can be un-screwed from the rear; some others from the inside after removing the exhaust.

Jul 12, 2015 | 2006 Triumph Rocket III

1 Answer

How to remove baffles


Step 1 - Remove Exhaust Remove the whole exhaust from the bike.
Step 2 - Drill Out the Baffle With a ½" hole saw and a handheld drill, insert them into a hole in the exhaust's outlet. The handheld drill will not go further inside the exhaust once you hit the baffle. Drill through the 1st baffle and then each remaining baffle until they are are drilled. Remove the baffle pieces.
Step 3 - Replace Exhaust Reinstall back the exhaust system onto your bike.

Jul 12, 2015 | Motorcycles

1 Answer

Removing baffles


go to the mechanic and look in manual of bike good luck

Jun 24, 2013 | Triumph Speedmaster Motorcycles

1 Answer

My suzuki gsxr 1000 k3 will start then cut out six times before it runs properly on its own in the cold


Instructions
  1. Take Down
    • 1 Park the motorcycle on the kickstand or center stand and allow the exhaust pipes to cool completely.
    • 2 Refer to your Suzuki service manual and organize the metric tools needed to remove the baffle. On newer models, it may be necessary to remove the tailpipe section to modify the baffle. On older models, you may be directed to remove a bolt that secures the baffle in the tailpipe.
    • Follow the procedure given in the manual and remove the tailpipe section or slide-in baffle using the appropriate tools. Save any brackets or bolts. Place the tailpipe or baffle on a workbench.
    Tailpipe Baffles
    • 4 Hold one end the tailpipe up to a light and look inside the other end. Depending on the baffle, you may see very little light or none at all. Modifying the baffle is a matter of opening up areas in the baffle.
    • 5 Chuck a 1/4-inch drill bit in an electric drill. Use a bit extension if necessary to reach deep into the tailpipe with the drill bit.
    • 6 Place the tailpipe on a workbench. Use a towel or rags to prevent scratching the finish. Insert the tip of the drill bit into the tailpipe and drill a 1/4-inch hole in the baffle.
    • 7 Hold the tailpipe up to the light again. Determine the number of additional holes you want based on the purpose of the modification. Drill additional holes in the baffle if needed.
    • 8 Stand the tailpipe on end and tap it on the workbench to clear the debris from drilling out of the baffle. Make sure all debris is cleared out before reinstalling the tailpipe on the motorcycle.
    Slide-In Baffles
    • 9 Secure the outer end of the baffle in a bench vise with the baffle extending to one side. The outer end has the threaded hole where the bolt was removed to take the baffle out of the exhaust pipe.
    • 10 Measure the length of the baffle and divide it by four. You modify a slide-in baffle by cutting off a one-quarter section at a time using a hacksaw. Mark the baffle at the one-quarter point and cut the first section off the end.
    • 11 Reinstall the baffle in the exhaust pipe using the saved bolt and the metric tool.
      Start the motorcycle and determine if the modification produced the desired result.
    • 12 Allow the exhaust pipe to cool completely before removing the baffle for further modification. Most likely, cutting one or two quarter sections will give you the result you want. Avoid cutting too much off the baffle, or it will be useless.

Jan 17, 2013 | Motorcycles

1 Answer

Are the outer forks the same on a gsx 1400 k4 as. K5 ?


Instructions
  1. Take Down
    • 1 Park the motorcycle on the kickstand or center stand and allow the exhaust pipes to cool completely.
    • 2 Refer to your Suzuki service manual and organize the metric tools needed to remove the baffle. On newer models, it may be necessary to remove the tailpipe section to modify the baffle. On older models, you may be directed to remove a bolt that secures the baffle in the tailpipe.
    • 3 Follow the procedure given in the manual and remove the tailpipe section or slide-in baffle using the appropriate tools. Save any brackets or bolts. Place the tailpipe or baffle on a workbench.
    Tailpipe Baffles
    • 4 Hold one end the tailpipe up to a light and look inside the other end. Depending on the baffle, you may see very little light or none at all. Modifying the baffle is a matter of opening up areas in the baffle.
    • 5 Chuck a 1/4-inch drill bit in an electric drill. Use a bit extension if necessary to reach deep into the tailpipe with the drill bit.
    • 6 Place the tailpipe on a workbench. Use a towel or rags to prevent scratching the finish. Insert the tip of the drill bit into the tailpipe and drill a 1/4-inch hole in the baffle.
    • 7 Hold the tailpipe up to the light again. Determine the number of additional holes you want based on the purpose of the modification. Drill additional holes in the baffle if needed.
    • 8 Stand the tailpipe on end and tap it on the workbench to clear the debris from drilling out of the baffle. Make sure all debris is cleared out before reinstalling the tailpipe on the motorcycle.
    Slide-In Baffles
    • 9 Secure the outer end of the baffle in a bench vise with the baffle extending to one side. The outer end has the threaded hole where the bolt was removed to take the baffle out of the exhaust pipe.
    • 10 Measure the length of the baffle and divide it by four. You modify a slide-in baffle by cutting off a one-quarter section at a time using a hacksaw. Mark the baffle at the one-quarter point and cut the first section off the end.
    • 11 Reinstall the baffle in the exhaust pipe using the saved bolt and the metric tool.
      Start the motorcycle and determine if the modification produced the desired result.
    • 12 Allow the exhaust pipe to cool completely before removing the baffle for further modification. Most likely, cutting one or two quarter sections will give you the result you want. Avoid cutting too much off the baffle, or it will be useless.

1_16_2013_4_34_52_am.jpg

Jan 15, 2013 | Suzuki GSX 1400 Motorcycles

1 Answer

Why wont my baffle come out of my akropovic exaust, i have removed the screw but its seems stuck solid? gaz


If thebaffle has not been removed before it may well be stuck in with the silicone sealent that is used to seal the exhaust, you should be able to twist the baffle to losen it, it is not unusual for the baffle to become tight, when eventualy you remove it clean the seating area and use a copper anti seize grease when replacing it, as suggested by most exhaust m,fctrs

Aug 31, 2011 | Yamaha yZFR125 Motorcycles

1 Answer

How do you remove baffle from Yoshimura exhaust


Most yoshimura exhausts have a large circlip holding in the baffle, some have an 8mm Bolt or alun head bolt, remove the retainer and grip baffle twist an pull slightly to remove some baffles have silicone around them to seal it which could hamper removal

Aug 08, 2011 | 2000 kawasaki ZX-6R Ninja

1 Answer

The proses to take out the baffles of my 2006 yamaha royal star touring deluxe.


Typically to remove baffles out of the exhaust you either need to remove the bolts in the muffler or drill out rivets. Once either are removed the process is pretty simple with pulling out the insert and removing the baffles.

Good luck

May 26, 2011 | Yamaha Royal Star Tour Deluxe Motorcycles

1 Answer

Exhaust problem


Dont do it ... motorcycles are delicately balanced for best operation. Not to mention removing the baffle will annoy those of us who will have to listen to you roar past.

Apr 27, 2010 | 2005 Benelli TnT

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

76848 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...