Question about Motorcycles

Open Question

2011 polaris ranger 400 no spark

Ignition module, cdi box , coil all good also new battery

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
rselvy
  • 83 Answers

SOURCE: Rear cylinder not firing

The first thing I would do is replace the spark plugs again. You can foul a plug and it will cause you more problems than you can ever imagine. I see you have done all the logical things that I would recommend but I did not see you have replaced the plugs after the 200 miles. You would be surprised at how many times a $2.00 part can cause fits beyond belief.

Posted on Dec 08, 2008

Ad
  • 3567 Answers

SOURCE: no spark 110cc engine wont start

Check the fuses. Next, check for spark but with a new spark plug. How good is the battery? If needed, add water to the battery cells enough to cover the top of the cell plates.Try a jump start from your car battery. Is the kill switch on? Check the operation of the ignition switch with a volt ohmmeter. You should be getting power into and out of the ignition switch.

If the bike doesn't start and run properly check the side stand kill switch. It kills the engine so that you don’t start out with the side stand down. Broken or out of adjustment, it would kill the spark. Check for a broken wire at the switch or coupler. Get a service manual and check out the electrical section. Some bikes have a diode integrated into the turn signal relay. Try moving the kill switch by hand. If that doesn’t work then wire a jumper around the switch to bypass it. If that doesn’t work, check out the relay.

Check the wiring harness. Did a wire come unplugged? Are all wires clean and with solid connections? Any abraded or pinched wires? Is the bike in neutral and the neutral light is lit up? If no neutral light, check the neutral switch and neutral switch wire on center casing.

Please rate this answer. Thanks

Posted on May 28, 2009

Benimur
  • 6966 Answers

SOURCE: 1996 zx11 getting sprk to one bank only

Hi and welcome to FixYa,

The voltage on the green wire must be pulsating when cranking/starting the bike, not steady. Confirm by similarly testing the voltage on the black wire on the left ignition coil. If the green still reads a constant voltage, then the CDI is faulty; to be more specific, most likely that the switching tansistor inside the CDI that drives the right ignition coil has shorted.

Good luck and thank you for asking FixYa.

Posted on Jul 10, 2009

  • 221 Answers

SOURCE: 1980 gs 550 l no spark ..I was told to relace ignition module

yes

Posted on Jul 24, 2009

polarcycle
  • 1392 Answers

SOURCE: Low voltage at coil on 1983 DR 250

Check for a short, or partially broken wire between CDI and coil. If your wiring is goodbetween there, check between CDI and pick up.

Posted on Jul 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2002 Yamaha Road Star Midnight has no spark


Hi, Jeff orange wires are usually, but not always, power wires and the usual suspects are:
1. Fouled spark plugs.
2. Severely discharged or a damaged battery, should have 12.5 volts or better and be able to pass a load test if necessary.
3. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Loose connection at ignition coil or plug between ignition sensor and CDI box.
5. Spark plug cables in bad condition, shorting / leaking, spark plug cable connections loose, check for spark leakage in the dark.
6. Faulty ignition coil, pick up coil, trigger coil or CDI box testing needs to be checked with an ohmmeter at 70 degrees Fahrenheit
7. Faulty safety switches clutch, kickstand, neutral, off/on etc.
8. Faulty ignition switch.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
Re No spark to the rear cylinder Road Star Forum Yamaha Road Star
How to diagnose no spark situation on motorcycle
Yamaha XV16AL Service Manual
OEM parts for Yamaha
Yamaha ROAD STAR XV16A Owner Manual

Nov 30, 2016 | 2002 Yamaha Road Star Midnight

1 Answer

1400 intruder no fire to the coil pack front cylinder coil is good stater is OK fuses good new pulse good .is the cdi out


Hi, Earl and the usual suspects are:
1. Fouled spark plugs.
2. Severely discharged or a damaged battery, should have 12.5 volts or better and be able to pass a load test if necessary.
3. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Loose connection at ignition coil or plug between ignition sensor and CDI box.
5. Spark plug cables in bad condition, shorting / leaking, spark plug cable connections loose, check for spark leakage in the dark.
6. Faulty ignition coil, pick up coil, trigger coil or CDI box testing needs to be checked with an ohmmeter at 70 degrees Fahrenheit
7. Faulty safety switches clutch, kickstand, neutral, off/on etc.
8. Faulty ignition switch.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
How to diagnose no spark situation on motorcycle
Image gallery
OEM parts for Suzuki
Suzuki VS1400 Owner Manual

Oct 25, 2016 | Suzuki VS 1400 Intruder Motorcycles

1 Answer

I have no fire...checked all the basic options...


Hi, Leisha and the usual suspects are:
1. Fouled spark plugs.
2. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
3. Loose connection at ignition coil or plug between ignition sensor and module.
4. Spark plug cables in bad condition, shorting / leaking, spark plug cable connections loose.
5. Faulty ignition coil or ignition / electronic module
6. Failed CKP, CMP, or BAS sensor.
7. Faulty ignition switch.
8. Security alarm failing to disarm needs reset
For more information about your issue and valuable free downloads that you will need please visit the websites below. Good luck and have a nice day.
TROUBLE SHOOTING
How to diagnose no spark situation on motorcycle
How to test motorcycle CDI box ignition coil
Testing your motorcycle coil


Mar 03, 2016 | Motorcycles

1 Answer

Hi, my zzr1100 will turn over but I have no spark, I have replaced both coils with new ones, replaced - fuse box, CDI,pickup coil and put new plugs in. Can you tell me what's up..... Thanks Anthony.


Hi, Anthony if you have a CKP sensor it needs compression to send the correct signal to the ICM/ECM, make sure both spark plugs are in heads and use a grounded third plug to check for spark or hold spark plug cable close to spark plug in the head. If still not getting spark the usual suspects are:
1. Fouled spark plugs.
2. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
3. Loose connection at ignition coil or plug between ignition sensor and module.
4. Spark plug cables in bad condition, shorting / leaking, spark plug cable connections loose.
5. Faulty ignition coil or ignition / electronic module
6. Failed CKP, CMP, or BAS sensor.
7. Faulty ignition switch.
8. Security alarm failing to disarm needs reset
For more information about your issue and free downloads that you will need please visit the websites below. Good luck and have a nice day.
http://zzrbikes.com/threads/59960-ZZR-1100-CDI-problem
zzr 1100 Workshop Visordown
http://motorhead.jactup.com/ZX-11/tech/ZX11_Service_93_01-converted.pdf

Feb 02, 2016 | Motorcycles

1 Answer

My predator 500 los park it will spit a spark and then quit could it be my CDI box


Hi, Chris it may very well be your CDI otherwise the usual suspects are:
1. Fouled spark plugs.
2. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
3. Loose connection at ignition coil or plug between ignition sensor and module.
4. Spark plug cables in bad condition, shorting / leaking, spark plug cable connections loose.
5. Faulty ignition coil or ignition / electronic module
6. Failed CKP, CMP, or BAS sensor.
7. Faulty ignition switch.
8. Security alarm failing to disarm needs reset
For more information about your issue and free downloads that you will need please visit the websites below. Good luck and have a nice day.
predator 500 no spark Polaris ATV Forum
ATV Connection
https://www.tradebit.com/filesharing.php/search/0/polaris+predator+500

Jan 24, 2016 | Motorcycles

1 Answer

1983 Honda no spark. Spark come out engine up to the Cdi that's is brand new . But I have no. Spark come out of Cdi to ignition coil (new) what color wire should it come out on ? To lead to ignition coil...


Hi, Anonymous and the usual suspects are:
1. Fouled spark plugs.
2. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead -acid batteries.
3. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Loose connection at ignition coil or plug between ignition sensor and module.
5. Spark plug cables in bad condition, shorting/leaking, spark plug cable connections loose check for spark leakage in the dark.
6. Faulty ignition coil or electronic control module.
7. Faulty pulse coil.
8. Faulty CKP, CMP, or BAS sensor.
9. Faulty ignition switch.
10. Tilt sensor needs a reset.
11. Security alarm failing to disarm needs reset
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
No spark 1983 vt500c my first bike only ran week
Magna 1984 V65 with no spark in all four spark plugs
1980 1100 no spark to plugs GL1100 Information Questions goldwingdocs com
Testing Honda Coils and CDI boxes
How to diagnose no spark situation on motorcycle

Aug 12, 2017 | Motorcycles

1 Answer

Yz 125 1991 no spark


Hi, Anonymous and the usual suspects are:
1. Fouled spark plugs.
2. Severely discharged or a damaged battery, should have 12.5 volts or better and be able to pass a load test if necessary.
3. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Loose connection at ignition coil or plug between ignition sensor and module.
5. Spark plug cables in bad condition, shorting / leaking, spark plug cable connections loose.
6. Faulty ignition coil or electronic control module or CDI box.
7. Faulty CKP, CMP, or BAS sensor.
8. Faulty ignition switch.
9. Tilt sensor needs a reset.
10. Security alarm failing to disarm needs reset
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
YZ125 2003 2005 No Spark
How to fix No Spark Problem on Motorcycles and Dirt Bikes
YAMAHA YZ125 Owner Service Manual
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-yz-owners-manuals

Sep 18, 2012 | Yamaha YZ 125 Motorcycles

1 Answer

MY YAMAHA 650 V STAR WON'T START


Hi, Rgr_murray and the usual suspects are:
1. Fouled spark plugs.
2. Severely discharged or a damaged battery, should have 12.5 volts or better and be able to pass a load test if necessary.
3. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Loose connection at ignition coil or plug between ignition sensor and module.
5. Spark plug cables in bad condition, shorting / leaking, spark plug cable connections loose.
6. Faulty ignition coil or ignition / electronic module
7. Faulty CKP, CMP, or BAS sensor.
8. Faulty ignition switch.
9. Tilt sensor needs a reset.
10. Security alarm failing to disarm needs reset
11. Faulty CDI box.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
no start or no spark
http://www.starbikeforums.com/forums/18-engine-work/2886-no-spark.html
http://www.sloneservices.com/SilverBack/Other-Stuff/V-StarShopManual99-07.pdf
OEM parts for Yamaha
http://www.starmotorcycles.com/assets/service/manuals/2003/LIT-11626-16-05_22.pdf

Apr 17, 2011 | 2001 Yamaha V Star Classic

2 Answers

1996 zx11 getting sprk to one bank only


Hi and welcome to FixYa,

The voltage on the green wire must be pulsating when cranking/starting the bike, not steady. Confirm by similarly testing the voltage on the black wire on the left ignition coil. If the green still reads a constant voltage, then the CDI is faulty; to be more specific, most likely that the switching tansistor inside the CDI that drives the right ignition coil has shorted.

Good luck and thank you for asking FixYa.

Jul 09, 2009 | 1996 kawasaki GPZ 1100

1 Answer

No spark on Hyusu


Hi and welcome to FixYa,

For a "no spark" problem with a Hyosung RX125, check:
  • temporarily disconnect the battery. With the engine on at both the ignition switch and engine kill switch, verify that the green wire to the CDI does not measure 0 ohms to ground;
  • if it does, check the ignition switch and the engine kill switch;
  • it it measures anywhere between 50 ~ 500 ohms, then reconnect the battery and check that there is +12 on the orange wire going to the CDI with ignition switch on;
  • for a pulsating voltage (high ACV) at the white / blue wire coming from the CDI going to the ignition coil;
  • for a pulsating voltage (low ACV, 0.5VAC) at the green wire coming from the pulser coil going to the CDI; and
  • of course, check if the CDI (black / white) is connected to the ground.
Postback results of tests.

Good luck and thank you for using FixYa.

May 27, 2009 | 2001 Hyosung RX 125

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...