Question about 1981 Suzuki TS 185

1 Answer

Torque settings for a suzuki ts 125x 1987

Its a b reg if that's any help . couldn't find the 125 in what product is about so put in the closest i could find. thanks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,567 Answers

40 foot pounds or 450 inch pounds for the head bolts

Posted on Mar 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Torque pattern on 1978 Suzuki rm 125


Hi, Brad for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Suzuki, despair not, for a mere $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
http://www.venold.com/tl1000s/specs/torque_specs.html
Suzuki RM125 Owner Service Manual
OEM parts for Suzuki
Suzuki RM 125 75 78

Jul 17, 2016 | Suzuki RM 125 Motorcycles

1 Answer

Will a 1999 Suzuki RM 125 power valve assembly work on a 2000 Suzuki RM 125


Hi, Anonymous after careful deliberation 4 out 5 Suzuki Gods give this one a thumbs up, but just to be on the safe side you should give your local dealer's parts/service department a call to confirm. For more information about your question and valuable "FREE" downloads that you will need please visit the websites below. Good luck and have a nice day.
http://www.crservice.dk/Suzuki%20cross/RM125/RM125K7_01A.pd OEM parts for Suzuki
Suzuki RM 125 2002
http://www.autoevolution.com/moto/suzuki-rm125-1987.html#aeng_suzuki-rm125-1987-124

Mar 14, 2016 | Suzuki Motorcycles

1 Answer

I have a suzuki ts 125x its kick starts fine then when riding it cuts out but does start again when i kick it over ??


Check the carb , the float may be out of adjustment or you may have a bad fuel line not letting fuel get to carb. I would try that first.

Mar 03, 2015 | Suzuki Motorcycles

2 Answers

I have a 1987 kx 125 just put topend gasket set in with piston and rings and coolent is getting in the case bottom end anyone know why plz help me


It sounds as if you have rebuilt the engine without torqueing the head bolts. Although, it could be that the cylinder base gasket has been torn during the rebuild. Try to re-tighten the head bolts to the correct settings first. Good luck.

May 23, 2012 | 2003 kawasaki KX 125

1 Answer

How much oil should i put in my 1987 dr 125 suzuki


Abt 2.5L then check your dipstick it should reach between 2-2.5cm clean height on it

Apr 09, 2010 | 2005 Suzuki DR-Z 125 L

1 Answer

No spark on 1971 suzuki ts 125


Hi and welcome to FixYa,

Initially, check for pulsating voltage on the black/yellow wire from the magneto to the ignition coil. Additionally, temporarily disconnect the black/yellow wire to the ignition switch.

Perhaps a wiring diagram would be of additional help.

Good luck and thank you for asking FixYa.

Nov 26, 2009 | 1981 Suzuki TS 185

1 Answer

2005 Suzuki GZ 125...cannot get ignition barrel out. Need to replace lock set


hi i am a locksmith you have on the ignition 2x dome head bolts closest to fuel tank the only way to remove the ign is a hammer and centre punch use the punch to tap bolt undone

hope this helps

Jun 15, 2009 | 2003 Suzuki GZ 125 Marauder

1 Answer

I have a suzuki 125 ts was riding it then stop for


is it getting fuel? try tipping a very small amount of fuel down rhe plug hole, replace the plug if it fires you have a carb problem.

Apr 11, 2009 | 2003 kawasaki KX 125

1 Answer

Need head bolt torque settings for a 1985 model ts 185


The head bolts get torqued to 40 ft. lbs.

Please rate this answer. Thanks sheba11! < love the name

Apr 07, 2009 | 1981 Suzuki TS 185

1 Answer

Does anyone know the torque settings for head


7.2 ft lbs. ( or close ). Many torque wrenches are not extremely accurate at such low ranges.

Pleas rate this answer. Thanks sporter108!

Apr 05, 2009 | 1981 Suzuki TS 185

Not finding what you are looking for?
1981 Suzuki TS 185 Logo

Related Topics:

337 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4471 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...