Question about 2000 Harley Davidson FLHR-FLHRI Road king

1 Answer

Will not start, like a circuit breaker is switching off, batt at full charge, power on, push start button and everything shuts off

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 948 Answers

It sounds like your battery is bad. Put a voltmeter on the battery terminals and check the voltage when you press the start button. If it drops below ten, the battery is bad. If you take the battery to an auto parts place they can load test it and tell you if it is good. You could also try a blast of about 10 seconds with the horn. It pulls more power than just the lights but still may not fail if the battery is just on the edge.

There is no circuit breaker for the main power on a bike, you could have a fuse blowing but it would not come back on if it was.

Posted on Mar 11, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The dryer stopped working while in use. There is now no power going into the machine. It is a Bosch Maxx 7 dryer.


Electric dryer no start does nothing

Check dryer Terminal block prongs both outside prongs should give combined 220, and 110 each if u check 1 outside & 1 center (ground) prong. Also check house electrical outlet for full voltage.

CHECK THERMAL SHUT OFF THERMOSTAT USUALLY LOCATED ON THE BLOWER. for OHMS or resistance with a meter. Should show a closed circuit. Ohms WHEN THIS FUSE BLOWS IT WILL SHUT DOWN EVERYTHING.

NEXT Test the PUSH start switch with meter for OHMS. Should show OHMS when pushed in or on start, and no ohms or infinity when in off position.

If you hear a humming/clicking sound from motor area you more than likely have a bad motor.
Try this test out to see if u have weak windings or relay/capacitor on motor.
Open the dryer door and turn by hand the drum while machine is on ON position. And you or someone else presses the door engagement switch in. If it starts up then u have bad windings

Another thing to check is the belt safety switch. With a multi meter.
Especially if u just replaced the belt. The belt safety switch is attached to the Tensioner and motor. IT LOOKS LIKE A DOOR SWITCH SOMEWHAT a little black pc of plastic with 2 prongs going into it. Sits at bottom of motor. Under the Tensioner. Attach meter clips to the 2 prongs on switch, Then when the little white push button is pressed in it should show continuity and none when released.

Lastly check ur DOOR SWITCH for continuity with a meter when the button is pushed in the (on/Door closed position,) it may have gone bad.

https://www.youtube.com/watch?v=sTRP6kHqAFs
Hey GOD IS GOOD !!!! WHICH IS WHY MY ADVICE IS FREE




25682338-k4ataymuwmgrdb2rqqdy5pxt-5-2.jpg

25682338-k4ataymuwmgrdb2rqqdy5pxt-5-5.png

25682338-k4ataymuwmgrdb2rqqdy5pxt-5-9.jpg

25682338-k4ataymuwmgrdb2rqqdy5pxt-5-14.jpg

25682338-k4ataymuwmgrdb2rqqdy5pxt-5-20.jpg

May 06, 2015 | Bosch Dryers

1 Answer

My whirlpool dryer model wed510vq0 has no power at all,i,ve reset breaker but it wasn't tripped what could be the problem?


Electric dryer no start does nothing

Check dryer Terminal block prongs both outside prongs should give combined 220, and 110 each if u check 1 outside & 1 center (ground) prong. Also check house electrical outlet for full voltage.

CHECK THERMAL SHUT OFF THERMOSTAT USUALLY LOCATED ON THE BLOWER. for OHMS or resistance with a meter. Should show a closed circuit. Ohms WHEN THIS FUSE BLOWS IT WILL SHUT DOWN EVERYTHING.

NEXT Test the PUSH start switch with meter for OHMS. Should show OHMS when pushed in or on start, and no ohms or infinity when in off position.

If you hear a humming/clicking sound from motor area you more than likely have a bad motor.
Try this test out to see if u have weak windings or relay/capacitor on motor.
Open the dryer door and turn by hand the drum while machine is on ON position. And you or someone else presses the door engagement switch in. If it starts up then u have bad windings

Another thing to check is the belt safety switch. With a multi meter.
Especially if u just replaced the belt. The belt safety switch is attached to the Tensioner and motor. IT LOOKS LIKE A DOOR SWITCH SOMEWHAT a little black pc of plastic with 2 prongs going into it. Sits at bottom of motor. Under the Tensioner. Attach meter clips to the 2 prongs on switch, Then when the little white push button is pressed in it should show continuity and none when released.

Lastly check ur DOOR SWITCH for continuity with a meter when the button is pushed in the (on/Door closed position,) it may have gone bad.

https://www.youtube.com/watch?v=sTRP6kHqAFs

Feb 22, 2015 | Whirlpool Dryers

1 Answer

I have an affinity dryer that wont come on. it blew a breaker. the breaker tested fine.


Check dryer Terminal block prongs both outside prongs should give combined 220, and 110 each if u check 1 outside & 1 center (ground) prong. Also check house electrical outlet for full voltage.

CHECK THERMAL SHUT OFF THERMOSTAT USUALLY LOCATED ON THE BLOWER. for OHMS or resistance with a meter. Should show a closed circuit. Ohms WHEN THIS FUSE BLOWS IT WILL SHUT DOWN EVERYTHING.

NEXT Test the PUSH start switch with meter for OHMS. Should show OHMS when pushed in or on start, and no ohms or infinity when in off position.

If you hear a humming/clicking sound from motor area you more than likely have a bad motor.
Try this test out to see if u have weak windings or relay/capacitor on motor.
Open the dryer door and turn by hand the drum while machine is on ON position. And you or someone else presses the door engagement switch in. If it starts up then u have bad windings

Another thing to check is the belt safety switch. With a multi meter.
Especially if u just replaced the belt. The belt safety switch is attached to the Tensioner and motor. IT LOOKS LIKE A DOOR SWITCH SOMEWHAT a little black pc of plastic with 2 prongs going into it. Sits at bottom of motor. Under the Tensioner. Attach meter clips to the 2 prongs on switch, Then when the little white push button is pressed in it should show continuity and none when released.

Lastly check ur DOOR SWITCH for continuity with a meter when the button is pushed in the (on/Door closed position,) it may have gone bad.

https://www.youtube.com/watch?v=sTRP6kHqAFs

Jun 03, 2014 | Frigidaire Dryers

1 Answer

Why does the 30 amp circuit breaker behind the battery box on my 1990 fatboy click once when i push the ignition button? The bike won't start.


Try to reset the circuit breaker. also check for an earth fault on the starter motor .If this is not a circuit breaker and is a relay, you should make sure everything is ready for a start, (ie : in neutral, sidestand up and clutch in and that the battery is charged.) the neutral light being "on" doesn't mean it is in neutral. I hope this helps.

Mar 08, 2012 | Motorcycles

2 Answers

DEWALT DG6300B NO POWER OUTPUT


Hello avid.....

If there is no power to the receptacles:

1. Turn the circuit breaker switches off and disconnect all electrical loads from the generator.


2. Turn the circuit breakers on and test the GFCI's by following the procedures in this manual

on page 1 -

TO TEST A GFCI:

Start the generator. Turn the auto idle switch off. Push in the TEST button (A) on the receptacle.

The RESET button (B) will pop out. Power is now off at the receptacle.

If the RESET button does not pop out, the GFCI is not working. Do not run

generator until the problem can be corrected. To restore power to receptacle,

push the RESET button in. If the RESET button pops out during operation,
stop the generator and check the generator and equipment for defects.

3. Place the voltage selector to the 120 Volt only positions (unless you are using a tool that

requires 240 Volts).


4. Turn the idle control switch off.


5. Turn the circuit breaker(s) off and reconnect the electrical loads. Be sure that the plugs are

securely connected to the receptacles.


6. Turn the circuit breaker(s) on.


7. If there is still no power at the receptacles, take the generator to an authorized DEWALT
service center. To locate a DEWALT service center nearest to you, call 1-800-4-DEWALT

Joe

Thanks for choosing Fixya!

Nov 27, 2010 | Garden

1 Answer

Not sure how to hook up wiring for 6.5 hp briggs with solenoid


OK
,Batt + to one of solenoid large post
Cable from solenoid lrge terminal opposit batt cable, to starter large terminal
Hot wire to start buttob wire from start button to small terminal on solenoid. Batt grd to engine.. GoodLuck, Ned

Oct 13, 2009 | Briggs & Stratton Ignition Kit 2-8 HP...

1 Answer

My C120 will not shut down using the red power off button


When you turn on the breaker switch push the nearest grey button to the powerbutton than you get a factoryrest your software shoud be 4.29

Jun 29, 2009 | Raymarine C120 System Pack C120 Raystar...

1 Answer

Trolling motor doesnt work?


Most trolling motors have in-line breakers, I would start there & see if one went bad, then check the wiring under the foot pedal for broken or corroded contacts, then you will have to trace wires & make sure everything is in order starting at the trolling motor plug.

May 24, 2009 | Boating

1 Answer

Whirl pool dryer LEC9000PW0 will not turn on


Has a household fuse blown or has a circuit breaker tripped?
There may be 2 household fuses or circuit breakers for the dryer. Make sure both fuses are intact and tight, or that both circuit breakers have not tripped. Replace the fuse(s) or reset the circuit breaker(s). If the problem continues, call an electrician.
Is the correct power supply available? (Electric dryers only)
Electric dryers require 240-volt power supply. Check with a qualified electrician.
Is the dryer door firmly closed?
Your dryer door may not be fully closed. It may look shut, but may not be latched. Push on the door to engage the latch or latches. Some models have an upper and lower latch. Both latches must be secure for the dryer to run.
Was the Start, Push to Start or Hold to Start button firmly pressed?
Large loads may require the Start, Push to Start, or Hold to Start button to be pressed and held for two to five seconds.
Is the Cycle Control knob set on a Sensor Dry or Timed Dry cycle? (on some models)
The Cycle Control knob must be set in a Automatic Dry or AccudryTM or Timed Dry cycle. The dryer will not start if set on the Wrinkle ShieldTM option.
Is Controls Locked status light on? (on some models)
Press and hold the Cycle Signal button for three seconds. This will turn off the Controls Locked feature.
Did you recently install a power supply cord on the dryer? (Electric dryers only)
The power supply cord may be incorrectly installed. If the power cord is incorrectly installed, the dryer may not start or heat. Review the Installation Instructions to check that the power supply cord is properly installed.

Dec 02, 2008 | Whirlpool Duet GHW9150P Front Load Washer

Not finding what you are looking for?
2000 Harley Davidson FLHR-FLHRI Road king Logo

182 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...