Question about 2000 Yamaha YZF-R1

1 Answer

Cuts out sometimes at low rpms and doesnt doit other times

Cuts out at low rpms sometimes but then cleans out at higher rpms.But then doesnt doit other times. Just started doing it after it sat in the rain for 3 days!

Posted by on

  • crmetalmulis Mar 11, 2009

    Its a 2000 yamaha r1

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 69 Answers

May have a little water in the ram air intake and the air filter may be wet, try removing it and blowing out relly good with a high pressure air hose.good luck.

Posted on Mar 12, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Chokes out at 8500 rpm


try running some SEAFOAM gas treatment through it. Might take a few tank but it should clean out the carbs

Oct 04, 2012 | 2003 Yamaha YZF-R6

1 Answer

Whenever I pull up to make a stop my car drops dead. Sometimes I just got a tune-up can you help.


Your trottle body may have gunk on it. When an engine idles it lets little air in for just a low RPM run so it doesnt die. If it is gunked up just spray some carb cleaner on a COLD Engines throttle body flag and scrub it off and see it if still idles fine. If it runs fine at higher rpms that is mmore than likely the solution :D Alright Good luck man.

Mar 29, 2011 | 1995 Dodge Avenger

1 Answer

1994 silverdo 75000 miles wont chane into high all time sometimes it wont move when changing into higher gear **** when you stop cut off it runs good next time happens about once a week thinking computer...


Sounds like a symptom of a low fluid level or either a clogging filter. Change your fluid and the filter, and see if this doesnt alleviate your problem.

Aug 07, 2010 | 1994 Chevrolet K1500

1 Answer

The bike backfires at low RPMs we just cleaned up the whole carb for varnish and dirt and it still does it. Thanks John


bout time to hav jets ajusted or replaced-please let a pro doit cause to lean or rich can blow ur engine

Aug 05, 2010 | 1997 kawasaki VN 1500 Vulcan Classic

1 Answer

1986 mighty max 2.0 engine makes a ticking noise most of the time. At higher rpms it stops. What could it be ? It kind of sounds ike a vaccum leak ? maybe ?


A ticking sound is usually a valve and if it stops at higher rpms I would guess it is oil related. Seems like the oil pump might be getting tired and not pumping enough at low rpms.

Mar 19, 2010 | 1986 Mitsubishi Mighty Max

1 Answer

Low power in low rpms, higher rpms runs ok


CK EXHAUSR GFOR SELL OF SILPHUR. Catalyctic converter appears to be restricted.

May 17, 2009 | 1992 Chevrolet C1500

1 Answer

2000 yamaha r1 cuts out sometimes at low rpms


check for a vacum leak by the fuel shut off valve.if the system leaks vacum.It can cause the symptoms you are stating

Mar 11, 2009 | 2000 Yamaha YZF-R1

1 Answer

Cuts out sometimes at low rpms 2000 yamaha r1


Hvae you put on an aftermarket pipe? If so I owuld recomend rejetting the carbs. It probaly happens alot when the temp changes outside.

Mar 11, 2009 | 2000 Yamaha YZF-R1

2 Answers

Mess up


Your bike is most likely running a little lean on the idle/slow-speed circuit. The jets might need a cleaning, or you've got a slight air leak somewhere. Other possibilities ... - Idle mix screw out of adjustment (Probably not as it's sealed and 'supposed to be' tamper free) - Carbs slightly out of synch

Nov 10, 2008 | 1995 Yamaha FZR 1000

Not finding what you are looking for?
2000 Yamaha YZF-R1 Logo

Related Topics:

162 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

278 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

D. E. Hev

Level 3 Expert

1167 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...