Question about 1994 Yamaha XV 535 Virago DX

1 Answer

Going to customize my 750 virago. im removing the air induction system and change to a gravity fed gas tank along with after market pipes. Is there any possible problems i might run into and need to be aware of before i start?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 69 Answers

When changing to aftermarket pipes on a carburated bike I would recommend have the carbs rejetted, the after market pipes will change the fuel mixture and could cause the bike to run a little funny.

Posted on Mar 11, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the valve adjustment specs for a 2008 Roketa 250 cc scooter


2008?? right their is valve with a vacumn pipe from the inlet manifold to the valve on the bottom of the fuel tank ,gravity fed . check the pipe and if its not split or perished then you may need a new valve

Nov 04, 2015 | Cars & Trucks

1 Answer

HOW DO I REMOVE THE SEAT AND GAS TANK FROM AN 88 VIRAGO 750?


if memory serves me right it should have two bolts holding the seat on then there should be a bolt for the tank after you remove the seat ,if not bolts on the seat there would be a key holder cheers

May 21, 2014 | 1996 Yamaha XV 535 Virago DX

2 Answers

Hi I have an '81 yamaha virago 750,I don't know how to adjust the carbs,it getting too much gas and I was told I needed to close the gas off and open the air.....????


Below is a diagram. Turn the air screw inward until it lightly seats then open it up two turns. Set the idle speed with the throttle screw. The throttle screw pushes against a lever on the outside of the carb. From there, adjust the air screw for best idle speed. Do this for both carbs. Be sure the air cleaner is clean.
tombones49_110.gif

Apr 25, 2011 | Yamaha XV 535 Virago DX Motorcycles

1 Answer

2004 mercury sable gas go's into tank real slow


This is caused by an obstructed filler air pipe vent, this keeps the air from coming out of the tank as you fill, this causes the filler nozzle at the station to shut off as the gas backs up in the filler pipe, the air vent pipe is either kinked or blocked in some way. The vent tube runs down along side the gas fill tube and is all one part, replace it.

Mar 15, 2011 | 2004 Mercury Sable

2 Answers

How many gallons for a 1997 yamaha virago 535 gas tank?


Main tank: 3.6 U.S. gal. (13.5 L, 3.0 Imp. gal.)

Reserve: 0.7 U.S. gal. (2.5 L, 0.5 Imp. gal.)

Oct 21, 2010 | 1997 Yamaha XV 535 Virago DX

2 Answers

Fuel runs out the the right vent tube and breather hole when the engine is running. Disconnect the vac line from fuel tank and no leak. Is the vac fuel pump overpresuring the system? 1982 Suzuki GS750


Most likely the diaphragm in the fuel tap has a hole in it .The way your fuel system works is that, when the bike cranks and starts it generates a vacuum in the inlet manifold, a pipe from the manifold goes to the fuel tap. The vacuum in the pipe pulls the diaphragm in the tap away from the holes in the tap ,letting fuel flow past the diaphragm and down into your carburetors ( gravity fed).
If there is a hole in the diaphragm the vacuum will **** fuel through the diaphragm and down the vacuum pipe flooding that cylinder and starving the others.
I hope this helps.

Mar 28, 2010 | 1981 Suzuki GS 750 L

3 Answers

750 89' Yamaha Virago gas & oil coming out of air cleaner


sounds like the floats are stuck. cleaning carbs should do the trick. its a good practice to start up motorcycles and let them warm up from time to time while being stored.

May 04, 2009 | 1989 Yamaha FZX 750

2 Answers

95 xv750 Virago fuel leak


Probabilly a stuk carburettor float or needle.
Try to solve this problem to gently tap on the carburettor bodies. If this doesn't help you have to clean out the carburettors, and/or replace the float neeldes

Apr 02, 2009 | 1995 Yamaha XV 535 Virago DX

2 Answers

When I pump gas, it will spill out of the tank when its not full


there is a vent pipe/tube that runs along the fill pipe, this vent allows air out of the tank when u fill it, it has to be obstructed, replace it.

Mar 17, 2009 | 2003 Ford Focus

Not finding what you are looking for?
1994 Yamaha XV 535 Virago DX Logo

Related Topics:

445 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

276 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

D. E. Hev

Level 3 Expert

1167 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...