Question about 2003 Yamaha YZ 125

1 Answer

Front lihts - 2003 Yamaha YZ 125

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,567 Answers

Remove the headlight from it'd housing. Check to be sure the bulb is good. Next check the wiring from the headlight to the connection inside the housing. Be sure all connections are good. Check the fuses near the battery.

Posted on Mar 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

NNeed torque specs for 2010 harley ultara classic, front axle nut, front brake calipers, axle nut holder


Front Axle = 60 to 65 foot pounds

Front caliper banjo bolts = 17 to 19 foot pounds

Front Brake disk screws = 16 to 29 foot pounds

Front caliper mounting bolts = 28 to 38 foot pounds

Front axle holder nuts = 132 to 180 inch pounds

Aug 23, 2014 | 2010 Harley Davidson FLHTCUTG Tri Glide...

1 Answer

What are the torque specs for 2010 harley ultra classic, front axle nut, front brake calipers


Front caliper -

Brake Pad Pin = 75-102 INCH lbs.

Caliper to Fork Bolts = 28-38 FOOT lbs.

Aug 23, 2014 | 2010 Harley Davidson FLHTCUTG Tri Glide...

1 Answer

Front forks on a 1987 Honda Goldwing motorcycle how to change them


Place bike on center stand.
Jack the front of the bike to raise the front wheel off the ground. Be careful!!!
Remove the front wheel.
Remove the front fender and cross brace.
Disconnect the brake calipers from the forks.
Remove the air connections from the fork tops.
Loosen the fork leg clamp bolts on the triple tree.
Slide each leg out of the bike. Twisting while pulling often helps.
This can also be done without removing the front wheel but you will have to elevate the front of the bike another foot or so - just disconnect the air fittings and brake calipers, loosen the clamp bolts and drop the whole front assembly.

Jul 22, 2014 | Motorcycles

1 Answer

All lihts ar on but buton to start not respond


When you push start button, do you hear a rapid series of clicks, or a single click?

Jan 30, 2014 | Harley Davidson FLSTC Heritage Softail...

1 Answer

2013 ultra classic torque spec's on Rotors front Axle's front and rear


Front axle nut torque 70-75ft lbs, rear axle cone nut first torque 15-20ft lbs, second torque 95-105 ft lbs, front disc torque 16-24 ft lbs, rear disc torque 30-45ft lbs.

Nov 24, 2012 | 2005 Harley Davidson FLHTCUI Electra Glide...

1 Answer

No problem I need torque spec's front brake rotor,front axle nut and front brake caliper bolts 2005 Harley davidson ultra classic


caliper torque 28-38 ft lbs,front axle nut torque60-65 ft lbs. front brake rotor torque 16-24 ft lbs. straight from harley manuel.

Aug 14, 2011 | 2005 Harley Davidson FLHTCUI Electra Glide...

1 Answer

I have just purchased a Kawasaki 98 GPXR motorbike and need to replace the front wheel tyre. How do i go about removing the wheel so that i can take it to the mechanics to get this done?


Torque specs:

Front axle = 80 ft/lb
Front axle clamp bolt = 15 ft/lb
Front axle caliper mounting bolts = 25 ft/lb

Front Wheel Removal:

1. While the bike is still on the rear stand (but before putting it on the front stand), loosen the front axle clamp bolt with a 6mm hex bit. You do not need to remove it fully, just be sure it's loose.

2. Using the 14mm hex bit, loosen the front axle bolt. A breaker bar makes this step easier. Once it is loose you can go ahead and place the motorcycle on the front stand.

3. Using the 12mm socket, remove the front brake caliper mounting bolts. Once you have the brake off of the rotor, replace the bolts back in the caliper to prevent losing them. Hang the brake using cable ties or twine. BE SURE NOT TO PUSH THE BRAKE PEDAL! This will compress the brake pads and make it difficult to re-install. Repeat the process for the other side.

4. Once the brakes are tied off out of the way, finish removing the front axle bolt. It's helpful to use some wood to support the wheel while removing the axle bolt. Be sure to note the spacers on the wheel between the forks and the wheel. Remove them so they don't get lost. These will need to be greased before reinstalling.

5. Installation is the reverse of removal. Be sure to replace the calipers and torque them to 25 ft/lb. Once the front axle bolt has been torqued to 80 ft/lb, be sure to drop the front to the ground and bounce the front forks 4-5 times. This will seat the forks on the axle. Then you can tighten the front axle clamp bolt to 15 ft/lb.

Mar 26, 2011 | kawasaki GPX 750 R Motorcycles

1 Answer

Yamaha vstar 1100 classic motorcycle manual?


first take scews out or head light unit locaded on either side at 3 n the 9 oclock position they should be a phillips then you should be able to remove the bulb it depends on if light does not work and you have replaced bulb you need to use 12volt test light and check for power on the back of bulb I have had at least 3 times that bulb was good an the spade connection on back of ligt it self if you do not have a test light I would pick one up at walmart or local parts store they are pretty cheap and give lot of advise when chacking fo 12 volt power you need to ground the test light bye attaching its ground clip to anything meatal on motor or fram be ccareful not to put onpainted ares when you take the point end of the test light and check the plugthat attaches to the liht the ligt can be unplugged you should have one wire that lights your light when key is on and one that lights the light only when your high beam indacater is on the other wire is a ground if you have no power on thet plug you need to check fuse for the lights if fuse is good may have problem in handle bar switch if it is the switch try a little wd-40 in the switch an then work it back an forth blow excess out with air hope this info helps

Jul 10, 2010 | 2002 Yamaha V Star 1100 Classic

1 Answer

Need torque specs for front wheel cross pin and nut and bolt in fork on 2005 1200 custom


Front axle nut = 50-50 ft. lbs.
Front axle pinch bolt and nut = 21-27 ft. lbs.
Front brake caliper mounting bolts = 25-30 ft. lbs.
Handlebar clamp bolts = 12-15 ft. lbs.
Front Fork
Upper bracket pinch bolts = 30-35 ft. lbs.
Lower bracket pinch bolts = 30-35 ft. lbs.
Fork stem pinch bolt = 30-35 ft. lbs.
Front fender fasteners = 9-13 ft. lbs.

Mar 03, 2010 | 2005 Harley Davidson XL 1200 C Sportster...

Not finding what you are looking for?
2003 Yamaha YZ 125 Logo

Related Topics:

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1128 Answers

D. E. Hev

Level 3 Expert

1059 Answers

mikeuk

Level 2 Expert

61 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...